Opens in a new tab

IS25WP256D-JLLE

256Mbit SPI NOR Flash, 1.8V, QPI/QSPI, 104MHz, DTR, WSON-8 6x8mm, -40 to 105C

13368

Effective Inventory

Image for reference only

Manufacturer Part:

IS25WP256D-JLLE

Package:

8-WSON (6.0 x 8.0 x 0.73 mm, exposed pad)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The IS25WP256D-JLLE is a ISSI product designed for electronic applications. It features compact design with reliable performance characteristics suitable for various industrial and consumer applications.

Key Specifications

Memory Type SPI NOR Flash
Density 256Mbit (32MB)
Organization 32M x 8
Interface SPI / Dual I/O / Quad I/O / QPI / DTR
Max Clock Frequency (Single/Dual/Quad) 133 MHz (at 1.65-1.95V)
Max Clock Frequency (QPI) 133 MHz
DTR Mode Clock 80 MHz (equivalent 664 Mbps)
Supply Voltage 1.65V to 1.95V (1.8V Typ)
Active Read Current 7.5 mA (Typ)
Standby Current 10 uA (Typ)
Deep Power Down 1 uA (Typ)
Page Size 256 bytes
Sector/Block Size 4KB / 32KB / 64KB uniform
Program/Erase Cycles 100,000
Data Retention 20 Years
Addressing Mode 3-byte or 4-byte
Operating Temperature -40 C to +105 C (Extended)
Package 8-WSON (6.0 x 8.0 mm, exposed pad)
Security 4x256B OTP, 128-bit Unique ID, Advanced Sector Protection

Features

256Mbit SPI NOR Flash with 1.8V supply; Supports Standard/Dual/Quad SPI, QPI, and DTR modes; 133MHz clock in Quad I/O; 80MHz DTR for 664 Mbps throughput; 3-byte and 4-byte addressing modes; QPI mode with 2-cycle instruction for reduced overhead; Uniform 4KB/32KB/64KB sector/block erase; Program/Erase Suspend and Resume; AutoBoot operation for rapid startup; Configurable drive strength and dummy cycles; 4×256-byte dedicated OTP security area; 128-bit unique ID per device; Advanced sector/block protection; Power supply lock protection; Deep power down (1uA); SFDP (Serial Flash Discoverable Parameters) support; Extended temperature range to +105C

Applications

Automotive infotainment and ADAS; Industrial embedded systems; FPGA configuration storage; IoT and connected devices; Smart meters and energy management; Telecom and networking; Data storage and code shadowing; Execute-in-place (XIP) applications

Product Introduction: IS25WP256D-JLLE Product Introduction

The IS25WP256D-JLLE from ISSI is a 256Mbit (32MB) SPI NOR Flash memory device operating at 1.8V (1.65V to 1.95V), designed for high-performance code and data storage in embedded and automotive applications. The device supports a comprehensive set of SPI interfaces including Standard SPI, Dual I/O, Quad I/O, QPI (Quad Peripheral Interface), and DTR (Double Transfer Rate) modes, achieving up to 664 Mbps equivalent throughput in QPI DTR mode. The 4-byte addressing mode enables access to the full 256Mbit density, while 3-byte mode provides backward compatibility for legacy controllers. The QPI mode reduces instruction overhead to just 2 clock cycles, significantly improving random access performance for XIP (execute-in-place) applications. The JLLE package designation indicates the 8-contact WSON (6x8mm) package with exposed thermal pad, providing excellent thermal performance in a compact footprint. The device features 4KB, 32KB, and 64KB uniform sector/block erase, program/erase suspend and resume for real-time interrupt handling, and AutoBoot for automatic data output after power-on reset. Security features include a 128-bit unique device ID, 4×256-byte OTP (one-time programmable) security areas, and advanced sector/block protection with power supply lock.

Working Principle: IS25WP256D-JLLE Working Principle

The IS25WP256D-JLLE operates through a serial peripheral interface where the host controller communicates by asserting CS# and clocking commands, addresses, and data via the SI, SO, SCK, and WP#/HOLD# pins (which become bidirectional IO0-IO3 in multi-I/O modes). In Standard SPI mode, commands and addresses are sent serially on SI (IO0) and data is returned on SO (IO1). In Quad I/O mode, all four I/O pins are used for both address and data transfer, quadrupling the effective bandwidth. QPI mode goes further by using 4-bit instruction encoding, reducing the command phase from 8 serial clocks to just 2 quad-clock cycles. DTR (Double Transfer Rate) transfers data on both rising and falling edges of SCK, effectively doubling the data rate per pin. The memory array is organized as uniform 4KB sectors that can also be erased in 32KB or 64KB blocks. Programming loads up to 256 bytes into a page buffer before the internal write state machine applies high-voltage pulses to inject charge into the floating gates. The 4-byte addressing mode extends the address space beyond 128Mbit by using 32-bit addresses, essential for accessing the full 256Mbit density. The AutoBoot feature stores a configuration in non-volatile registers that automatically triggers a read sequence after power-on, enabling the MCU to boot directly from the flash without first issuing read commands.

Pin Description: IS25WP256D-JLLE Pin Definition and Functions
Pin Name Type Function
1 CS# Input Active-low chip select; selects the device for SPI operations
2 SO/IO1 I/O Serial data output in SPI; IO1 in Dual/Quad/QPI modes
3 WP#/IO2 I/O Write protect in SPI; IO2 in Quad/QPI modes
4 VSS Power Ground reference
5 SI/IO0 I/O Serial data input in SPI; IO0 in Dual/Quad/QPI modes
6 SCK Input Serial clock; controls data transfer timing up to 133MHz
7 HOLD#/IO3 I/O Hold in SPI; IO3 in Quad/QPI modes; RESET# in dedicated option
8 VCC Power Power supply (1.65V to 1.95V)
EP Exposed Pad Thermal Thermal pad connected to VSS; solder to PCB for heat dissipation
Application Scenarios: In which products and applications is IS25WP256D-JLLE used
  • FPGA Configuration: Stores FPGA bitstream with AutoBoot enabling rapid configuration after power-on, and 4-byte addressing for large 256Mbit images.
  • Automotive ADAS: Provides 1.8V SPI NOR Flash for radar and camera ECUs with extended temperature range to +105C and QPI for high-bandwidth code access.
  • IoT and Wearables: Ultra-low 1uA deep power down and 1.8V operation ideal for battery-powered connected devices requiring code storage.
  • Industrial XIP: Enables execute-in-place for industrial MCUs with 664 Mbps QPI DTR throughput eliminating RAM shadowing overhead.
Alternative Models: What chips are recommended as replacements for IS25WP256D-JLLE
Manufacturer Part Number Package Density Notes
ISSI IS25LP256D-JLLE WSON-8 256Mbit 3V version (2.3-3.6V)
ISSI IS25WP256D-MLLE 16-SOIC 256Mbit SOIC package variant
Macronix MX25V25635FMI WSON-8 256Mbit 1.8V pin-compatible alternative
Winbond W25V256JVEIQ WSON-8 256Mbit 1.8V QSPI NOR alternative

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1