Product Overview
The BlueNRG-M2SA from STMicroelectronics is a Bluetooth Low Energy v5.2 certified system-on-chip application processor module based on the BlueNRG-2 SoC. It features an ultra-low-power Cortex-M0 core, 256 kB Flash, 24 kB RAM, and an integrated chip antenna in a compact 11.5 x 13.5 mm form factor. The module includes a pre-certified RF platform with embedded balun and harmonic filter.
Key Specifications
| Bluetooth Specification | BLE v5.2 certified |
| Core | ARM Cortex-M0 (32-bit, up to 32 MHz) |
| Flash Memory | 256 kB (programmable) |
| RAM | 24 kB (with data retention) |
| Output Power | Up to +8 dBm |
| Receiver Sensitivity | -88 dBm |
| Supply Voltage | 1.7V to 3.6V |
| Operating Temperature | -40°C to +85°C |
| Module Size | 11.5 x 13.5 x 2 mm |
| Antenna | On-board chip antenna (SMD) |
| Link Budget | Up to 96 dB |
| Interfaces | UART, I2C, SPI, 14 GPIO, 2 timers, 10-bit ADC |
Features
- Bluetooth v5.2 certified with BQE qualification
- Supports master and slave modes simultaneously (multiple roles)
- LE Data Packet Length Extension support
- Embedded BALF-NRG-02D3 matched balun with harmonic filter
- AES-128 security co-processor
- Embedded 32 kHz oscillator and SMPS inductor for ultra-low power
- Multi-regional certifications: CE, FCC, IC, TELEC, SRRC, KCC, WPC
Pre-programmed UART bootloader - 10-year longevity program commitment
Applications
- Smart home and building automation
- Wearable health and fitness devices
- Industrial IoT sensor nodes and asset tracking
- Beaconing and proximity detection
- Human-machine interface devices
- Bluetooth Mesh networking
Product Introduction: BLUENRG-M2SA Product Introduction
The BlueNRG-M2SA is a Bluetooth Low Energy system-on-chip application processor certified module from STMicroelectronics. It is certified under Bluetooth LE specifications v5.2 and is BQE qualified. The module is based on the BlueNRG-2 SoC, featuring an ultra-low-power Cortex-M0 32-bit core with 256 kB of programmable Flash memory and 24 kB of RAM with data retention. The entire Bluetooth LE stack and protocols are embedded in the module. The BlueNRG-M2SA provides a complete RF platform in a tiny form factor, integrating the radio, chip antenna, high-frequency oscillators, and matched balun (BALF-NRG-02D3) with harmonic filter. It can be powered directly from a pair of AAA batteries or any source from 1.7V to 3.6V.
Working Principle: BLUENRG-M2SA Working Principle
The BlueNRG-M2SA operates through four key subsystems:
1. Processing Core: An ARM Cortex-M0 32-bit RISC core runs at up to 32 MHz, executing both the Bluetooth LE protocol stack and user application code. The 256 kB Flash stores firmware and application code, while 24 kB RAM holds runtime data with retention in low-power modes.
2. RF Transceiver: The 2.4 GHz radio supports Bluetooth LE modulation with output power up to +8 dBm and -88 dBm receiver sensitivity, achieving a 96 dB link budget. The embedded BALF-NRG-02D3 balun provides impedance matching and harmonic filtering. An on-board chip antenna radiates the RF signal.
3. Low-Power Management: A 32 kHz crystal oscillator enables ultra-low-power BLE sleep modes. An integrated SMPS inductor reduces active-mode current consumption. The module supports multiple low-power states including sleep with RAM retention.
4. Peripheral Interfaces: The module exposes UART, I2C, SPI, 14 GPIOs, two multifunction timers, a 10-bit ADC, DMA controller, watchdog, RTC, and SWD debug interface. An AES-128 hardware co-processor handles encryption for LE Secure Connections.
Pin Description: BLUENRG-M2SA Pin Definition and Functions
Pin Name Type Function 1 VBAT Power Power supply (1.7–3.6V) 2 GND Power Ground 3 RESET Input Active-low reset 4 UART_TX Output UART transmit / GPIO 5 UART_RX Input UART receive / GPIO 6 SPI_CS I/O SPI chip select / GPIO 7 SPI_CLK I/O SPI clock / I2C SCL / GPIO 8 SPI_MOSI I/O SPI MOSI / I2C SDA / GPIO 9 SPI_MISO I/O SPI MISO / GPIO 10 IRQ Output Interrupt request / GPIO 11–14 GPIO[10:13] I/O General-purpose I/O (multi-function) 15 SWDIO I/O SWD debug data 16 SWCLK Input SWD debug clock Application Scenarios: In which products and applications is BLUENRG-M2SA used
- Smart home devices: BLE-connected thermostats, door locks, and lighting controllers with mesh networking support
- Wearable health monitors: Fitness bands and medical sensors powered by coin cells with 1.7V minimum supply
- Industrial IoT: Asset tracking beacons and remote monitoring sensors with pre-certified RF for fast time-to-market
- HMI peripherals: Wireless keyboards, remote controls, and industrial operator panels using UART/SPI host interface
- Building automation: Occupancy sensing and environmental monitoring with Bluetooth Mesh networking
Alternative Models: What chips are recommended as replacements for BLUENRG-M2SA
Manufacturer Part Number Package Notes STMicroelectronics BlueNRG-M2SP Module (11.5×13.5) PCB antenna version, lower cost STMicroelectronics BlueNRG-M0A Module BLE 4.2, SPI network processor only Nordic nRF52832-QFAA QFN-48 BLE 5.0, Cortex-M4, 512kB Flash Silicon Labs BGM13S22F512GA Module BLE 5.0, Cortex-M4, pre-certified Texas Instruments CC2640R2FRGZR QFN-32 BLE 5.0, Cortex-M3, 128kB Flash Espressif ESP32-C3-WROOM-02 Module BLE 5.0 + Wi-Fi, RISC-V Recommend Parts

TMP275AIDR
0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC
Brand: TI
Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)
IN STOCK: 3681pcs
Cargo cycle: 3-7 Days
The minimum order is 1

IRFS4227TRLPBF
IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)
Brand: infineon
Package: D2PAK (TO-263)
IN STOCK: 4334pcs
Cargo cycle: 3-7 Days
The minimum order is 1

CD4070BM96
Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14
Brand: TI
Package: SOIC-14 (8.75 x 3.9 x 1.5mm)
IN STOCK: 4245pcs
Cargo cycle: 3-7 Days
The minimum order is 1

LP2980IM5-5.0
50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5
Brand: TI
Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)
IN STOCK: 2557pcs
Cargo cycle: 3-7 Days
The minimum order is 1












