The MSP430F5324IRGCR from Texas Instruments is a 16-bit ultra-low-power MSP430 MCU in a 64-pin VQFN (9×9 mm) package. Key specs include 25-MHz CPU, 64-KB Flash, 6-KB SRAM, 12-bit SAR ADC (10 channels), 8 comparators, hardware multiplier (32-bit), 3-channel DMA, 2 USCI modules (each supporting UART/SPI and I2C), 4 16-bit timers (Timer_A ×3, Timer_B ×1), 47 GPIOs, and RTC with alarm. Operating voltage is 1.8 V to 3.6 V. Power consumption: 290 µA/MHz active (Flash), 1.9 µA standby (LPM3 with RTC), 0.18 µA shutdown (LPM4.5), with 3.5-µs wake-up from standby. Industrial temperature range -40°C to +85°C.
Home » Clock & Timing ICs, Integrated Circuits ICs » MSP430F5324IRGCR
MSP430F5324IRGCR
16-bit MSP430, 64KB Flash, 6KB SRAM, 12-bit ADC, 0.18µA LPM4.5, 3.5µs wake-up, VQFN-64, 1.8-3.6V
Effective Inventory
Manufacturer Part:
MSP430F5324IRGCR
Package:
VQFN-64 (RGC) (9.0 x 9.0 x 0.95 mm, 0.5mm pitch, exposed pad)
Brand:
Product Categories:
Quality Commitment
Shipping & Payment
Service & Packaging
Product Manual
Other recommendations you may be interested in.
Description
Product Introduction: MSP430F5324IRGCR Product Introduction
The MSP430F5324 is a member of TI’s MSP430F532x family of ultra-low-power 16-bit mixed-signal microcontrollers. The ‘5324’ variant provides 64-KB Flash, 6-KB SRAM, and 47 I/O pins in a 64-pin VQFN package, positioned as a mid-range device between the smaller 28-pin and larger 80-pin family members.
The MSP430 architecture is optimized for low-power operation through a combination of flexible clock management, multiple low-power modes, and an integrated LDO. The unified clock system includes a digitally controlled oscillator (DCO) for fast wake-up (3.5 µs from standby), a FLL for frequency stabilization, a 32-kHz crystal oscillator (XT1) for RTC, and a high-frequency crystal oscillator (XT2) up to 32 MHz. The on-chip LDO regulates the core supply, allowing the device to run from a single 1.8-V to 3.6-V supply.
The five low-power modes are the hallmark of the MSP430. Active mode draws 290 µA/MHz from Flash (150 µA/MHz from RAM). LPM3 (standby with RTC, WDT, and supply supervisor active) draws only 1.9 µA at 2.2 V. LPM4 (off mode with RAM retention and supply supervisor) draws 1.1 µA. LPM4.5 (shutdown with no RAM retention) draws just 0.18 µA — approaching the self-discharge rate of a coin cell battery.
The two USCI modules each support dual-protocol operation: USCI_A provides UART (with auto-baud detection) and SPI, while USCI_B provides I2C and SPI. This allows simultaneous UART + I2C, or SPI + I2C, or any combination. The 12-bit ADC includes an internal reference, sample-and-hold, and auto-scan for sequential channel sampling without CPU intervention.
The hardware multiplier supports 32-bit operations (32×32 → 64-bit result) in a single instruction cycle, accelerating DSP-like algorithms. The 3-channel DMA offloads memory transfers from the CPU, enabling ADC-to-RAM or UART-to-RAM transfers with zero CPU overhead.
Typical applications include battery-powered data loggers, wireless sensor nodes, portable medical instruments, and smart metering systems where ultra-low quiescent current and fast wake-up are essential for extending battery life.
Working Principle: MSP430F5324IRGCR Working Principle
**MSP430 CPU Core:** The MSP430 uses a 16-bit RISC architecture with 16-bit registers and a constant generator for efficient instruction encoding. The 27 core instructions handle most operations; additional emulated instructions provide convenience. The Von Neumann architecture uses a single address space for Flash, SRAM, and peripherals. The CPU runs at up to 25 MHz with single-cycle register-to-register operations.
**Unified Clock System (UCS):** The UCS manages four clock sources: XT1 (32-kHz crystal), XT2 (high-frequency crystal up to 32 MHz), DCO (digitally controlled oscillator, fast start), and VLO (low-frequency internal, 10 kHz typical). The FLL multiplies the 32-kHz reference to generate a stable MCLK and SMCLK. The DCO starts in microseconds, enabling the 3.5-µs wake-up from LPM3.
**Low-Power Modes:** Five low-power modes trade off functionality vs. power. LPM0 keeps SMCLK running (timer-based events). LPM3 keeps only ACLK (32 kHz) and RTC active (periodic wake-up). LPM4 disables all clocks but retains SRAM (interrupt wake-up). LPM4.5 disables the LDO entirely, losing SRAM content but achieving 0.18 µA (reset wakeup). The key design principle: spend most time in deep sleep, wake briefly to take measurements, then return to sleep.
**USCI Communication:** Each USCI module uses a shared shift register with separate baud-rate generators for UART and I2C/SPI modes. Switching between protocols requires reconfiguration but not a hardware change. The UART supports auto-baud detection for unknown baud rates. I2C supports master/slave with multi-master arbitration and clock stretching.
Pin Description: MSP430F5324IRGCR Pin Definition and Functions
| Pin Group | Count | Key Functions | Notes |
|---|---|---|---|
| Power (DVCC/DVSS) | 4 pairs | 1.8-3.6V digital supply; AVCC/AVSS for analog | Bypass each DVCC with 0.1µF ceramic; AVCC powers ADC and comparators |
| PORT1 (P1.0-P1.7) | 8 | GPIO with interrupt; TA0 CCR0-4; ADC A0-A7; comparator inputs; TMS/TCK (JTAG) | P1.0 can output ACLK; P1.2/P1.3 are USCI_B0 I2C default pins |
| PORT2 (P2.0-P2.7) | 8 | GPIO with interrupt; TA1 CCR0-2; ADC A8-A9; comparator outputs; TDI/TDO (JTAG) | P2.0 can output SMCLK; P2.4/P2.5 are USCI_A0 UART default |
| PORT3 (P3.0-P3.7) | 8 | TA0 outputs; USCI_A0 SPI (UCA0CLK/SIMO/SOMI); USCI_B0 SPI | Port 3 handles most SPI pin assignments for both USCI modules |
| PORT4 (P4.0-P4.7) | 8 | TA2 CCR0-2; TB0 outputs; XT1 crystal pins; ADC A10-A12 | P4.0/P4.1 are XT1 IN/OUT (32kHz crystal); P4.2-P4.4 are TB0 outputs |
| PORT5-11 | 15 | USCI_A1 (UART/SPI); USCI_B1 (I2C/SPI); XT2 crystal; additional ADC; DMA control | Provides second USCI port pins; XT2 on P5.2/P5.3 for high-freq crystal |
| RST/NMI | 1 | Reset / non-maskable interrupt; active low; internal pull-up | External pull-up and decoupling cap recommended for clean reset |
Application Scenarios: In which products and applications is MSP430F5324IRGCR used
| Application | Description |
|---|---|
| Battery-Powered Data Logger | Wake from LPM3 on RTC alarm (1.9µA standby); sample ADC channels via auto-scan; store in SRAM via DMA; transmit via UART/I2C when buffer full; 0.18µA LPM4.5 for long idle; coin-cell operation for years |
| Wireless Sensor Node | LPM3 between radio transmissions; hardware multiplier for CRC/RSSI calculation; USCI_A for UART to radio module; USCI_B for I2C sensors; 3.5µs wake-up enables responsive event detection |
| Portable Medical Instrument | 12-bit ADC for biosignal acquisition; comparators for threshold detection; DMA offloads ADC-to-RAM transfer; RTC timestamps readings; wide voltage (1.8-3.6V) for direct lithium cell operation |
Alternative Models: What chips are recommended as replacements for MSP430F5324IRGCR
| Model | Manufacturer | Compatibility | Key Difference |
|---|---|---|---|
| MSP430F5329IPN | TI | Series Upgrade | 128-KB Flash / 8-KB SRAM; 80-pin LQFP; 63 I/O; same peripherals; more memory and pins; use when 64KB Flash is insufficient |
| MSP430F5328IZQE | TI | Series Alternative | 64-KB Flash / 6-KB SRAM; 80-pin BGA (5x5mm); same peripherals; smaller footprint; use for ultra-compact designs |
| MSP430F5524IRGCR | TI | Functional Upgrade | Same VQFN-64 pinout; adds USB 2.0 PHY; 64-KB Flash / 4-KB SRAM; use when USB connectivity required |
| STM32L052C8T6 | ST | Competitive Alternative | 32-bit ARM Cortex-M0+; 64-KB Flash / 8-KB SRAM; USB 2.0; 12-bit ADC; LQFP-48; 0.27µA standby; use when 32-bit performance preferred |
Recommend Parts

RK73H1ETTP20R0F
20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200
Brand: KOA Speer
Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm
IN STOCK: 33180pcs
Cargo cycle: 3-7 Days
The minimum order is 1

TPS77001DBVR
50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5
Brand: TI
Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)
IN STOCK: 5000pcs
Cargo cycle: 3-7 Days
The minimum order is 1

TPS61021ADSGR
3A synchronous boost converter, 1.8-5.5V, VSSOP-8
Brand: TI
Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)
IN STOCK: 12398pcs
Cargo cycle: 3-7 Days
The minimum order is 1

S1MB-13-F
1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C
Brand: Diodes Inc
Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)
IN STOCK: 3679pcs
Cargo cycle: 3-7 Days
The minimum order is 1

ADUM5000ARWZ-RL
500mW isolated DC-DC converter, 3.3/5V, SOIC-16W
Brand: ADI
Package: SOIC-16W (10.3 x 7.5 mm, RW package)
IN STOCK: 6373pcs
Cargo cycle: 3-7 Days
The minimum order is 1

IN STOCK: 9357pcs
Cargo cycle: 3-7 Days
The minimum order is 1






