Opens in a new tab

NC7SZ66P5X

SPST bus switch, 1.65-5.5V, 5Ω Ron, sub-ns delay, rail-to-rail, SC-70-5, OE active-high

2290

Effective Inventory

Image for reference only

Manufacturer Part:

NC7SZ66P5X

Package:

SC-70-5 / SOT-353 / SC-88A (2.0 x 1.25 x 1.0 mm, 0.65mm pitch)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

The NC7SZ66P5X from onsemi (formerly Fairchild) is a single-pole/single-throw (SPST) bus switch from the TinyLogic UHS family in a 5-pin SC-70 package (2.0 x 1.25 mm). It operates from 1.65 V to 5.5 V with 5 Ω typical on-resistance, rail-to-rail signal handling, and sub-nanosecond propagation delay at 5 V. The switch is enabled when OE is HIGH (connecting port A to port B) and open when OE is LOW. Power-down high-impedance I/O prevents backflow current. Operating temperature range is -40°C to +85°C. The P5X suffix denotes 3000-unit SC-70 tape-and-reel.

Product Introduction: NC7SZ66P5X Product Introduction

The NC7SZ66 from onsemi’s TinyLogic UHS family is a single-bit SPST bus switch in an ultra-small SC-70-5 package. The NC7SZ66P5X is the tape-and-reel version with 3000 units per reel. Originally designed by Fairchild Semiconductor (now part of onsemi), the device provides a low-impedance pass-through path between two ports with minimal propagation delay.

When the output enable (OE) pin is HIGH, the switch closes and port A connects to port B through approximately 5 Ω. When OE is LOW, the switch opens and a high-impedance state exists between the two ports. The switch handles signals from 0 V to VCC (rail-to-rail), and the 5 Ω on-resistance introduces negligible voltage drop for typical logic signals.

The key advantage of a bus switch over a buffer is zero propagation delay contribution other than the RC delay through the on-resistance and load capacitance. At 5 V, the propagation delay through the switch is typically 0.3 ns, making it essentially transparent to timing budgets.

The device supports over-voltage tolerant inputs up to 7 V, enabling voltage translation between different logic domains. When VCC is 0 V, all I/O pins enter a high-impedance state, preventing backflow current in partially-powered systems — critical for hot-swap and power-sequencing applications.

The NC7SZ66 is available in three packages: SC-70-5 (P5X), SOT-23-5 (M5X), and MicroPak-6 (L6X). The SC-70-5 version occupies only 2.5 mm² of board area.

Note: Some distributors list the NC7SZ66P5X as obsolete, but it remains available from multiple sources. Verify current availability before designing into new products.

Working Principle: NC7SZ66P5X Working Principle

**CMOS Transmission Gate:** The NC7SZ66 uses a CMOS transmission gate (parallel NMOS + PMOS) as the switch element. The NMOS passes signals near VCC well, while the PMOS passes signals near GND well. Together, they provide rail-to-rail signal handling with a relatively flat on-resistance across the full voltage range. The typical 5 Ω on-resistance is the parallel combination of both transistors.

**OE Control Logic:** When OE is HIGH, both the NMOS and PMOS gates are driven to turn on their respective transistors, creating a low-impedance path between A and B. When OE is LOW, both transistors turn off, isolating the two ports with high impedance and low off-state leakage (< 1 nA typical).

**Over-Voltage Tolerance:** Input and I/O pins incorporate circuitry that tolerates voltages up to 7 V independently of VCC. When a voltage above VCC appears on a switch port, the internal ESD diode to VCC is reverse-biased, preventing current flow into the VCC rail.

**Power-Off High-Impedance:** When VCC is 0 V, an internal circuit disables the switch and places all I/O in high-impedance, preventing any current path between ports or into the supply. This enables hot-swap and live-insertion applications.

Pin Description: NC7SZ66P5X Pin Definition and Functions
Pin Name Type Description
1 OE I Output enable (active HIGH); HIGH = switch on (A connected to B); LOW = switch open (high-Z between A and B); 7V tolerant; CMOS input levels
2 A I/O Switch port A; bidirectional; 0 to VCC signal range; 5Ω Ron to port B when enabled; 6pF I/O capacitance; high-Z when disabled or powered down
3 GND G Ground; connect to PCB ground plane
4 B I/O Switch port B; bidirectional; same characteristics as port A; signals pass through in either direction
5 VCC P Supply voltage; 1.65V to 5.5V; bypass with 0.1µF ceramic to GND; switch signal range is 0 to VCC
Application Scenarios: In which products and applications is NC7SZ66P5X used
Application Description
Bus Isolation / Hot-Swap Isolate I2C/SPI bus segments during card insertion; OE controlled by card-detect signal; power-off high-Z prevents backflow; 5Ω Ron adds negligible delay; multiple NC7SZ66 for multi-bit bus
Voltage Domain Isolation Disconnect 3.3V peripheral from 1.8V MCU during sleep; OE from GPIO; rail-to-rail signal handling; zero static power on switch path
Glue Logic Signal Steering Route one signal between two destinations using SPST switch; minimal propagation delay (0.3ns@5V) preserves timing; replaces multiplexer for simple 1:1 routing
Alternative Models: What chips are recommended as replacements for NC7SZ66P5X
Model Manufacturer Compatibility Key Difference
NC7SB6P5X onsemi Series Variant (Inverting) Inverting bus switch; same SC-70-5 package; signal inverted between A and B; use when inverted path needed
SN74LVC1G66DCKR TI Functional Equivalent SPST bus switch; 1.65-5.5V; 10Ω Ron; SC-70-5; higher Ron; TI-sourced alternative
NC7SZ66M5X onsemi Package Variant Same function in SOT-23-5 package; larger footprint but easier hand-soldering; different pinout
74AUC1G66DW-7 Diodes Inc Competitive Alternative SPST switch; 0.8-3.6V; lower Ron; smaller operating range; use for ultra-low voltage applications

Recommend Parts

RK73B2ATTD100J

10Ohm +/-5% 0.125W thick film resistor, 0805, +/-200 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0805 (2012 Metric) 2.0 x 1.25 x 0.55 mm

IN STOCK: 26435pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPL5010DDCR

Nano-power watchdog timer with power good, SOT-23-6

Brand: TI

Package: SOT-23-6 (2.9 x 1.6 x 1.1 mm, DDC package)

IN STOCK: 12122pcs

Cargo cycle: 3-7 Days

The minimum order is 1

NCP302045MNTWG

45V 5A programmable overcurrent protection switch, 50mΩ Ron, -60V reverse polarity, DFN-8

Brand: ON

Package: DFN-8 (3x3mm, 0.65mm pitch)

IN STOCK: 4759pcs

Cargo cycle: 3-7 Days

The minimum order is 1

WS2811

3-channel LED driver IC with built-in oscillator, SOP-8

Brand: Worldsemi

Package: SOP-8 (5.2 x 4.0 mm)

IN STOCK: 7374pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AD9912ABCPZ

1GSPS direct digital synthesizer with 14-bit DAC, LFCSP-64

Brand: ADI

Package: LFCSP-64 (9.0 x 9.0 mm, BCPZ package)

IN STOCK: 3719pcs

Cargo cycle: 3-7 Days

The minimum order is 1