Opens in a new tab

OPA4322AIPWR

Quad 20MHz CMOS op-amp, 0.5pA Ibias, 7nV/√Hz, RRO, 1.8-5.5V, 14-TSSOP

3472

Effective Inventory

Image for reference only

Manufacturer Part:

OPA4322AIPWR

Package:

14-TSSOP (5.0×4.4mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The OPA4322AIPWR from Texas Instruments is a quad-channel, low-noise, precision CMOS operational amplifier with 20MHz bandwidth and 0.5pA input bias current. Operating from a single 1.8V to 5.5V supply, it features 400μV offset voltage and 7nV/√Hz noise density. Housed in a 14-pin TSSOP package, it is ideal for low-power, high-impedance sensor applications.

Key Specifications

Category Quad Operational Amplifier
Number of Channels 4
Bandwidth (GBW) 20 MHz
Slew Rate 10 V/μs
Input Offset Voltage 400 μV (typical)
Input Bias Current 0.5 pA
Input Voltage Noise 7 nV/√Hz @ 1kHz
Supply Voltage 1.8V ~ 5.5V (single supply)
Quiescent Current per Channel 1.4 mA (typical)
Output Current ±50 mA (short circuit)
Rail-to-Rail Input and Output
Operating Temperature -40°C ~ 125°C
Package 14-TSSOP
Part Status Active

Features

  • Rail-to-rail input and output for maximum dynamic range
  • 20MHz GBW with only 1.4mA per channel
  • Ultra-low input bias current: 0.5pA
  • Low noise: 7nV/√Hz at 1kHz
  • Low offset voltage: 400μV typical
  • Single supply operation from 1.8V to 5.5V
  • Phase reversal protection
  • EMI filtered inputs
  • High capacitive load drive capability

Applications

  • High-impedance sensor interfaces
  • Photodiode and transimpedance amplifiers
  • Medical instrumentation
  • Battery-powered signal conditioning
  • Portable audio and data acquisition
Product Introduction: OPA4322AIPWR Product Introduction

The OPA4322AIPWR from Texas Instruments is a quad-channel, precision CMOS operational amplifier optimized for low-power, high-impedance sensor applications. The device combines 20MHz gain-bandwidth product and 10V/μs slew rate with an ultra-low input bias current of 0.5pA, making it ideal for interfacing with high-impedance sensors such as photodiodes, pH probes, and piezoelectric transducers. The rail-to-rail input and output stages maximize dynamic range in single-supply applications from 1.8V to 5.5V. With a low input offset voltage of 400μV and voltage noise density of 7nV/√Hz, the OPA4322 delivers precision performance for signal conditioning. Each channel consumes only 1.4mA, making the quad package efficient for multi-channel systems.

Working Principle: OPA4322AIPWR Working Principle

The OPA4322AIPWR uses a CMOS input stage that provides virtually zero input bias current (0.5pA), eliminating the offset errors caused by bias current flowing through high-impedance source resistors. The rail-to-rail input stage uses complementary PMOS/NMOS differential pairs that cover the entire supply range. The output stage uses a class-AB push-pull architecture for rail-to-rail output swing with low distortion. Internal EMI filtering on the inputs reduces susceptibility to RF interference. Phase reversal protection circuitry ensures the output does not invert when the input common-mode range is exceeded. The amplifier is internally compensated for unity-gain stability and can drive capacitive loads up to 1nF without oscillation.

Pin Description: OPA4322AIPWR Pin Definition and Functions
Pin Name Type Description
1 OUT A O Channel A output
2 -IN A I Channel A inverting input
3 +IN A I Channel A non-inverting input
4 V+ PWR Positive supply (1.8V-5.5V)
5 +IN B I Channel B non-inverting input
6 -IN B I Channel B inverting input
7 OUT B O Channel B output
8 OUT C O Channel C output
9 -IN C I Channel C inverting input
10 +IN C I Channel C non-inverting input
11 GND GND Ground / Negative supply
12 +IN D I Channel D non-inverting input
13 -IN D I Channel D inverting input
14 OUT D O Channel D output
Application Scenarios: In which products and applications is OPA4322AIPWR used
  • Photodiode TIA: Transimpedance amplifier for optical sensors with 0.5pA bias current
  • Medical Instrumentation: ECG/EEG front-end amplification with high input impedance
  • Multi-Channel DAQ: Quad op-amp for simultaneous 4-channel sensor signal conditioning
  • Portable Audio: Low-voltage audio preamplifier with low noise and RRO
  • Chemical Sensors: pH and gas sensor interface requiring ultra-low input current
Alternative Models: What chips are recommended as replacements for OPA4322AIPWR
Model Manufacturer Key Difference
OPA322AIPWR Texas Instruments Single channel, same specs, 8-SOIC
OPA2322AIPWR Texas Instruments Dual channel, same specs, 8-SOIC/MSOP
MCP6004-I/ST Microchip 1MHz GBW, lower cost, 14-TSSOP
TLV9004IPWR Texas Instruments 1MHz, 350μA/ch, ultra-low power alternative
ADA4522-4ARZ Analog Devices Zero-drift, 2.1μV offset, 14-SOIC

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1