Opens in a new tab

TJA1042T,118

CAN FD transceiver, 5Mbps, silent mode, 15uA standby, SOIC-8, automotive

6852

Effective Inventory

Image for reference only

Manufacturer Part:

TJA1042T,118

Package:

SOIC-8 (4.9 x 3.9 x 1.75 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TJA1042T,118 from Nexperia is a high-speed CAN transceiver with 5Mbps CAN FD support, silent mode, and +/-8kV ESD protection in an SOIC-8 package, optimized for automotive and industrial CAN networks.

Key Specifications

Interface High-Speed CAN (CAN FD)
Supply Voltage 4.75V to 5.25V
Data Rate Up to 5 Mbps (CAN FD)
Standby Current 15 uA (typ)
Operating Modes Normal, Silent, Standby
Bus Common-Mode Range -12V to +12V
ESD Protection +/-8kV IEC 61000-4-2 (HBM)
CANH/CANL Voltage -27V to +40V (short-circuit)
Package SOIC-8
Operating Temperature -40 to +150 C (TJ)

Features

  • Supports CAN FD up to 5Mbps
  • Silent mode (listen-only, no bus loading)
  • Very low 15uA standby current
  • Auto-thermal shutdown protection
  • +/-8kV ESD on CANH/CANL
  • Short-circuit protection to -27V/+40V
  • Optimized for 12V automotive battery systems
  • Pin-compatible with TJA1040/TJA1050

Applications

  • Automotive CAN bus networks
  • Industrial CAN/CAN FD
  • Gateway and gateway ECU
  • Body electronics and powertrain
Product Introduction: TJA1042T,118 Product Introduction

The TJA1042T,118 from Nexperia is a high-speed CAN bus transceiver that provides the interface between a CAN protocol controller and the physical CAN bus, supporting both classical CAN (up to 1Mbps) and CAN FD (Flexible Data Rate, up to 5Mbps). The device is optimized for 12V automotive battery systems and provides three operating modes: Normal mode for active communication, Silent mode (listen-only) where the receiver listens to the bus but the driver is disabled to avoid bus loading, and Standby mode with only 15uA current consumption for battery-saving sleep states. The Silent mode is particularly useful for diagnostic and monitoring applications where a node must observe bus traffic without affecting it. In Standby mode, the receiver can detect bus activity and wake up the microcontroller via the RXD pin, enabling low-power system designs. The CANH and CANL bus pins are protected against electrostatic discharge (ESD) to +/-8kV per IEC 61000-4-2, and against short-circuit voltages from -27V to +40V, covering all automotive fault conditions including battery reverse and load dump. The device features automatic thermal shutdown that disables the driver when junction temperature exceeds the threshold, protecting the device from bus contention or wiring faults. The TJA1042T is pin-compatible with the earlier TJA1040 and TJA1050, allowing easy upgrades from classical CAN to CAN FD. The ,118 suffix indicates Nexperia’s tape-and-reel packaging.

Working Principle: TJA1042T,118 Working Principle

The TJA1042T,118 operates as a high-speed CAN physical layer transceiver. Key subsystems include: (1) Driver Section – converts the TXD logic input to differential bus signals on CANH and CANL; a dominant TXD (low) drives CANH high and CANL low (approximately 3.5V and 1.5V, 2V differential); a recessive TXD (high) releases both lines (approximately 2.5V on both, 0V differential); the driver is disabled in Silent and Standby modes; (2) Receiver Section – monitors the differential voltage on CANH/CANL and outputs the result on RXD; dominant bus (>0.9V differential) drives RXD low; recessive bus (<0.5V differential) drives RXD high; the receiver remains active in Silent mode but the driver is disabled; in Standby mode, a low-power receiver monitors for bus wake-up patterns; (3) Mode Control – the STB (standby) pin selects the operating mode; STB high = Normal/Silent mode (depending on SPLIT pin); STB low = Standby mode; the mode transition is controlled by the host MCU; (4) CAN FD Support – the driver and receiver are designed for signal integrity at data rates up to 5Mbps with controlled edge rates and minimal bit timing distortion; the loop delay is specified for CAN FD bit timing requirements; (5) Protection – the bus pins have internal ESD clamp diodes rated for +/-8kV; series diodes protect against reverse battery; thermal shutdown disables the driver at approximately 165C; the split pin (when available) provides a common-mode stabilization voltage of VCC/2 for bus termination networks.

Pin Description: TJA1042T,118 Pin Definition and Functions
Pin Name Function
1 TXD Transmit data input (from MCU CAN controller)
2 GND Ground
3 VCC 5V supply
4 RXD Receive data output (to MCU CAN controller)
5 SPLIT Common-mode stabilization output (VCC/2)
6 CANL CAN bus low line
7 CANH CAN bus high line
8 STB Standby mode select (low = standby)
Application Scenarios: In which products and applications is TJA1042T,118 used
  • Automotive CAN FD gateway: 5Mbps CAN FD communication between ECUs with listen-only diagnostic mode
  • Body controller: manage door, window, and lighting nodes on CAN bus with 15uA standby for battery preservation
  • Industrial CAN: high-speed CAN FD for factory automation with 5Mbps burst data transfers
  • Diagnostic tool: Silent mode allows non-intrusive bus monitoring without loading the network
Alternative Models: What chips are recommended as replacements for TJA1042T,118
Manufacturer Part Number Package Notes
Nexperia TJA1042T SOIC-8 Tube version (not tape/reel)
Nexperia TJA1043T,118 SOIC-8 With INH output for power supply control
TI SN65HVD230DR SOIC-8 3.3V CAN transceiver, 1Mbps
Microchip MCP2562FD-E/SN SOIC-8 5V CAN FD, 8Mbps, VIO pin
Nexperia TJA1050T,118 SOIC-8 Classical CAN only, 1Mbps

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1