Opens in a new tab

UCC28600TDRQ1

QR flyback controller, 150W, green-mode, AEC-Q100, SOIC-8

7408

Effective Inventory

Image for reference only

Manufacturer Part:

UCC28600TDRQ1

Package:

SOIC-8 (4.9 x 3.9 x 1.58 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The UCC28600TDRQ1 from Texas Instruments is an AEC-Q100 qualified quasi-resonant flyback controller with green-mode capability in an 8-pin SOIC package. It operates in quasi-resonant mode at heavy loads, transitions to frequency foldback at medium loads, and enters green-mode burst operation at light loads for high efficiency across the entire load range, designed for automotive and industrial off-line power supplies up to 150W.

Key Specifications

Topology Quasi-resonant flyback controller
Maximum Output Power Up to 150W (with external MOSFET)
Operating Modes QR (heavy), FF (medium), Green burst (light)
Frequency Range Up to 130kHz (QR mode); down to 40kHz (FF)
Startup Current 25 uA typical
Operating Current 3 mA typical
VDD Range 8.0V to 24V (startup); UVLO 7.0V/8.0V
Gate Drive Output 1A source / 1A sink
OVP Overvoltage protection via VDD pin
OCP Pulse-by-pulse overcurrent protection
Thermal Shutdown Yes (internal)
CS Pin Blanking 250ns leading edge blanking
AEC-Q100 Qualified (Grade 1)
Operating Temperature -40 to +125 C
Package SOIC-8 (4.9 x 3.9 mm)
Status Active

Features

  • Quasi-resonant operation minimizes switching losses
  • Three-mode operation for high efficiency across load range
  • Green-mode burst operation at light load
  • 25uA ultra-low startup current
  • 1A gate drive for external MOSFET
  • Pulse-by-pulse overcurrent protection
  • Overvoltage protection via VDD
  • AEC-Q100 Grade 1 qualified
  • Internal thermal shutdown

Applications

  • Automotive off-line power supplies
  • Industrial SMPS up to 150W
  • LED lighting power supplies
  • Battery charger adapters
Product Introduction: UCC28600TDRQ1 Product Introduction

The UCC28600TDRQ1 from Texas Instruments is an AEC-Q100 Grade 1 qualified quasi-resonant flyback controller in an 8-pin SOIC package. The TD denotes the SOIC-8 package, R denotes tape and reel, and Q1 confirms the automotive -Q1 product designation. The controller drives an external N-channel MOSFET in a flyback converter topology with three operating modes optimized for efficiency across the entire load range: (1) Quasi-Resonant (QR) mode at heavy loads, where the MOSFET turns on at the valley of the drain voltage ringing, minimizing turn-on switching losses; (2) Frequency Foldback (FF) mode at medium loads, where the switching frequency decreases linearly with decreasing load to maintain high efficiency; (3) Green-mode burst operation at light loads, where the controller skips switching cycles entirely, reducing average switching frequency and losses. The 25uA startup current allows use of a high-value startup resistor from the rectified AC line, minimizing standby power. The controller uses primary-side regulation via the auxiliary winding for output voltage feedback, eliminating the need for an optocoupler in non-isolated or simple designs. Comprehensive protection includes pulse-by-pulse overcurrent, overvoltage via VDD, and thermal shutdown.

Working Principle: UCC28600TDRQ1 Working Principle

The UCC28600TDRQ1 operates through five subsystems: (1) Quasi-Resonant Control: During QR mode, the controller monitors the drain voltage through the auxiliary winding. After the MOSFET turns off and the secondary current reaches zero (demagnetization), the drain voltage rings due to the resonance of the primary inductance and MOSFET capacitance. The controller detects the valley of this ringing and turns on the MOSFET at the lowest point, minimizing capacitive turn-on losses (Eoss). This valley-switching technique significantly reduces switching losses compared to hard-switched flyback converters. (2) Frequency Foldback: As the load decreases, the controller reduces the switching frequency from the QR maximum (up to 130kHz) down to 40kHz. This reduces switching losses proportionally with load, maintaining high efficiency. The output is regulated by modulating the on-time. (3) Green-Mode Burst: At very light loads, the controller enters burst mode: it performs a few switching cycles to charge the output above regulation, then stops switching entirely. During the off period, only the 3mA operating current is consumed. This achieves very low standby power consumption. (4) Primary-Side Regulation: The auxiliary winding voltage reflects the output voltage during the secondary conduction period. The controller samples this voltage to regulate the output, typically achieving +/-5% regulation. For tighter regulation, an optocoupler can be used with the FB pin. (5) Protection: Pulse-by-pulse current limiting through the CS pin, OVP via VDD pin, and thermal shutdown protect the converter from fault conditions.

Pin Description: UCC28600TDRQ1 Pin Definition and Functions
Pin Name Type Description
1 SS I/O Soft-start capacitor (programs startup time)
2 FB Input Feedback input (optocoupler or internal regulation)
3 CS Input Current sense (MOSFET source resistor)
4 GND Power Ground
5 OUT Output Gate drive output (1A source/sink)
6 VDD Power Supply (8-24V, OVP monitoring)
7 DEM Input Demagnetization detection (aux winding)
8 LINE Input Line voltage compensation (brownout detect)
Application Scenarios: In which products and applications is UCC28600TDRQ1 used
  • Automotive 12V battery to 5V/3A off-line power supply using QR flyback with valley switching for low EMI and high efficiency at 150W
  • Industrial 24V output LED driver with quasi-resonant mode at full load and green-mode burst at standby for less than 0.5W no-load consumption
  • Laptop adapter 19V/4A using frequency foldback for medium-load efficiency and primary-side regulation for simplified design without optocoupler
  • Battery charger with pulse-by-pulse current limiting via CS pin and overvoltage protection via VDD for safe CC/CV operation
Alternative Models: What chips are recommended as replacements for UCC28600TDRQ1
Model Manufacturer Mode Power Notes
UCC28610DR TI QR 150W Non-Q1, commercial grade
NCP1377BDR2G onsemi QR 150W Similar QR controller
FAN6300HMY onsemi/Fairchild QR 120W Similar feature set
LD5530GL Power Integrations QR 65W Lower power, integrated MOSFET

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1