Opens in a new tab

AFE4490RHAR

Fully integrated 22-bit pulse oximeter AFE, 2-LED driver, 110dB dynamic range, VQFN-40

2870

Effective Inventory

Image for reference only

Manufacturer Part:

AFE4490RHAR

Package:

VQFN-40 (6.00 x 6.00 mm)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The AFE4490RHAR from Texas Instruments is a fully integrated analog front-end (AFE) for pulse oximeter applications. It integrates a 22-bit ADC, low-noise transimpedance amplifier with programmable gain, a flexible LED driver supporting H-bridge/push/pull configurations, and comprehensive diagnostics. Packaged in a VQFN-40 (6mm x 6mm), it enables complete pulse oximeter signal chains with minimal external components.

Key Specifications

ADC Resolution 22 bits
Number of LED Channels 2 (Red and IR)
LED Current Ranges 50mA, 75mA, 100mA, 150mA, 200mA
LED Current Resolution 8-bit per range
Dynamic Range 110dB across full range
Input-Referred Noise 50pARMS (at 5µA PD current)
Noise-Free Bits 13.5 (at 5µA PD current)
Rx Supply 2.0V to 3.6V
Tx Supply 3.0V or 5.25V
Rx Power Consumption <2.3mW at 3.0V
Interface SPI
Operating Temperature -40°C to +85°C
Package VQFN-40 (6 x 6 mm)

Features

  • Fully integrated AFE for pulse oximetry
  • Flexible LED driver with H-bridge, push, or pull configurations
  • 110dB dynamic range enabling low LED current operation
  • Programmable LED on-time: 50µs to 4ms
  • Analog ambient cancellation with 1µA to 10µA range
  • 7 separate feedback R and C settings per LED channel
  • Built-in photodiode and LED open/short diagnostics
  • Cable on/off detection

Applications

  • Clinical fingertip pulse oximeters
  • Wearable SpO2 monitoring
  • Industrial photometry
  • Optical biosensors
  • Patient monitoring systems
Product Introduction: AFE4490RHAR Product Introduction

The AFE4490RHAR is a complete analog front-end for pulse oximeter applications from Texas Instruments. It integrates a 22-bit ADC with a low-noise transimpedance amplifier (TIA), programmable second-stage gain, and an LED driver section that supports H-bridge, push, and pull configurations for both Red and IR LEDs. The device achieves 110dB dynamic range across the full LED current range, enabling operation at lower LED currents for power-sensitive wearable applications. Input-referred noise of 50pARMS at 5µA photodiode current delivers 13.5 noise-free bits of resolution. The flexible timing controller allows complete control over LED pulse sequencing with programmable on-time from 50µs to 4ms. Integrated diagnostics include photodiode and LED open/short detection plus cable on/off monitoring.

Working Principle: AFE4490RHAR Working Principle

The AFE4490RHAR operates as a synchronous sampling pulse oximeter AFE. The LED driver section drives Red and IR LEDs in a time-multiplexed sequence under control of the flexible timing controller. During each LED pulse, the photodiode current is converted to voltage by the TIA with seven selectable feedback resistor and capacitor settings per LED channel for optimal noise versus bandwidth tradeoffs. The second-stage amplifier provides additional programmable gain. An analog ambient cancellation circuit subtracts ambient light contribution (1µA to 10µA selectable) before the ADC. The 22-bit ADC digitizes each sample, and results are available via SPI. The timing controller independently manages LED2, Ambient(LED2), LED1, and Ambient(LED1) phases with programmable timing. Diagnostic circuits continuously monitor photodiode and LED integrity, reporting faults through the SPI interface.

Pin Description: AFE4490RHAR Pin Definition and Functions
Pin Name Type Description
1 INN Analog Input Negative input to TIA; connects to photodiode cathode
2 INP Analog Input Positive input to TIA; connects to photodiode anode
3 VCM Analog Output Common-mode voltage output; used as shield for INP/INN traces
10 TXN Power LED driver negative terminal; connects to LED cathode in H-bridge mode
11 TXP Power LED driver positive terminal; connects to LED anode in H-bridge mode
15 RX_ANA_SUP Power Analog receiver supply (2.0V to 3.6V)
20 LED_DRV_SUP Power LED driver supply (3.0V to 5.25V)
25 CLK Input External clock input from crystal oscillator (8MHz typical)
30 SPICLK Input SPI serial clock input
31 SPICS Input SPI chip select (active low)
32 SPIDIN Input SPI data input
33 SPIDOUT Output SPI data output
Application Scenarios: In which products and applications is AFE4490RHAR used
  • Clinical Fingertip Pulse Oximeter: Complete SpO2 and pulse rate measurement solution with Red (660nm) and IR (940nm) LED drivers, achieving clinical-grade accuracy with 22-bit resolution and 50pARMS input noise
  • Wearable SpO2 Monitor: Continuous blood oxygen monitoring in smartwatches and fitness bands with less than 2.3mW receive power and programmable low LED current operation extending battery life
  • Industrial Photometry: Precision optical measurement in liquid analysis and gas sensing applications using the flexible LED timing and 110dB dynamic range for wide concentration measurement
  • Patient Monitoring System: Multi-parameter patient monitors with integrated cable detection and LED/PD diagnostics ensuring reliable operation in hospital environments
  • Optical Biosensor: Research and development of PPG-based blood pressure and cardiac output estimation algorithms leveraging the high-resolution 22-bit data and flexible timing control
Alternative Models: What chips are recommended as replacements for AFE4490RHAR
Model Manufacturer Resolution LEDs Key Difference
AFE4404 TI 24-bit 3 Higher resolution, 3-LED support for SpO2 + multi-wavelength
AFE4405 TI 24-bit 4 4-LED, more flexible for advanced biosensing
MAX30102 ADI 18-bit 2 Integrated LEDs and PD in module package
MAX86141 ADI 19-bit 3 Higher resolution, 3-LED, lower power
OB1203 Renesas 20-bit 3 Integrated light-to-digital with ambient light sensor

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1