Opens in a new tab

Home » Integrated Circuits ICs, Sensors » ADXL1002BCPZ

ADXL1002BCPZ

3-axis MEMS accelerometer, ±50g, 25µg/√Hz noise, 11kHz BW, analog+SPI output, 5x5mm LFCSP

4370

Effective Inventory

Image for reference only

Manufacturer Part:

ADXL1002BCPZ

Package:

32-lead LFCSP (5 x 5 x 1.45mm)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The ADXL1002BCPZ is a high-performance, low-noise, 3-axis MEMS accelerometer from Analog Devices, optimized for condition-based monitoring (CbM) and vibration sensing. With an ultra-low noise density of 25µg/√Hz and bandwidth up to 11kHz, it captures detailed vibration signatures for predictive maintenance. The device operates from a single 3.3V supply and provides analog outputs directly proportional to acceleration.

Key Specifications

Number of Axes 3
Measurement Range ±50g
Resolution 16-bit (through SPI)
Noise Density 25µg/√Hz
Bandwidth 11kHz (X/Y), 5kHz (Z)
Sensitivity 40mV/g (typical)
Supply Voltage 3.0V to 3.6V
Supply Current 2.4mA (typical)
Interface Analog output + SPI (digital)
Package 5x5mm LFCSP (32-lead)
Operating Temperature -40°C to +125°C

Features

  • Ultra-low noise: 25µg/√Hz enables detection of subtle vibration signatures
  • Wide bandwidth: 11kHz for capturing high-frequency harmonics
  • ±50g measurement range for industrial vibration environments
  • Dual output: analog and 16-bit SPI digital
  • Integrated temperature sensor for compensation
  • 3.3V single-supply operation
  • Low power: 2.4mA typical
  • Aligned phase response across axes for modal analysis
  • Extended temperature range: -40°C to +125°C

Applications

  • Condition-based monitoring (CbM) and predictive maintenance
  • Industrial motor and bearing vibration monitoring
  • Structural health monitoring
  • Wind turbine and helicopter vibration sensing
  • Railway and transportation monitoring
  • Acoustic and vibration testing equipment
Product Introduction: ADXL1002BCPZ Product Introduction

The ADXL1002BCPZ is a high-precision 3-axis MEMS accelerometer from Analog Devices, specifically designed for condition-based monitoring and predictive maintenance applications. Its standout feature is the ultra-low noise density of 25µg/√Hz, which enables detection of incipient bearing faults and gear mesh abnormalities that lower-performance accelerometers would miss. The 11kHz bandwidth (X/Y axes) captures the high-frequency harmonics critical for diagnosing bearing defects. The device provides both analog and 16-bit SPI digital outputs, offering flexibility for system integration. An integrated temperature sensor facilitates thermal compensation algorithms. The 5x5mm LFCSP package is suitable for space-constrained sensor nodes.

Working Principle: ADXL1002BCPZ Working Principle

The ADXL1002 uses Analog Devices’ iMEMS technology with a polysilicon surface-micromachined sensing element. Each axis contains a differential capacitor structure whose plates move under acceleration, modulating the capacitance. An on-chip amplifier and demodulator convert this capacitance change to a voltage proportional to acceleration. The analog output provides a continuous real-time signal, while the integrated ADC digitizes the output at up to 16-bit resolution via the SPI interface. The signal conditioning path includes anti-aliasing filtering and offset correction. The aligned phase response across all three axes ensures accurate modal analysis and cross-axis correlation.

Pin Description: ADXL1002BCPZ Pin Definition and Functions
Pin Group Name Description
Power VDD, GND 3.3V supply and ground (multiple pins)
Analog Out OUTX, OUTY, OUTZ Analog acceleration outputs
SPI CS, SCLK, SDI, SDO 4-wire SPI interface for digital readout
Control ST Self-test input
Temp OT On-chip temperature sensor output
Config FC, R_SET Filter and range configuration pins
Application Scenarios: In which products and applications is ADXL1002BCPZ used
  • Motor Bearing Fault Detection: Mount the ADXL1002 on a motor housing to capture vibration signatures. The 25µg/√Hz noise floor detects early bearing wear patterns (ball pass frequency harmonics) months before failure. Use FFT analysis on the analog output to identify specific fault frequencies. The ±50g range accommodates both low-frequency imbalance and high-frequency bearing tones.
  • Structural Health Monitoring: Install on bridges, wind turbines, or building structures to monitor vibration modes. The aligned phase response across axes enables accurate operational modal analysis (OMA). The 11kHz bandwidth captures structural resonances in stiff structures. Low power enables solar or battery-powered wireless sensor nodes.
  • Industrial Gearbox Monitoring: Detect gear mesh abnormalities through high-frequency vibration analysis. The 16-bit SPI output provides high dynamic range for simultaneously monitoring low-speed shaft imbalance and high-speed gear mesh harmonics. Temperature sensor output compensates for thermal drift in continuous monitoring applications.
Alternative Models: What chips are recommended as replacements for ADXL1002BCPZ
Model Axes Range Noise Key Difference
ADXL1001 1 ±100g 30µg/√Hz Single-axis, wider range
ADXL355 3 ±2.048g 22.5µg/√Hz Lower range, digital only
MMA8452Q 3 ±8g 126µg/√Hz NXP, consumer-grade
LIS3DH 3 ±16g 150µg/√Hz ST, ultra-low power

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1