Opens in a new tab

MPL115A2

Digital barometer, 50-115kPa, I2C, ±1kPa accuracy, 5µA active, factory-calibrated, LGA-8 3x5mm

4300

Effective Inventory

Image for reference only

Manufacturer Part:

MPL115A2

Package:

LGA-8 (3 x 5 x 1.2 mm)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The MPL115A2 is a miniature digital barometer from NXP Semiconductors featuring a piezoresistive pressure sensor with I2C digital output. It measures absolute pressure from 50 to 115 kPa with 1 kPa accuracy over the -40°C to +105°C temperature range, housed in a compact LGA-8 (3 x 5 x 1.2 mm) package.

Key Specifications

  • Pressure Range: 50 kPa ~ 115 kPa (500 ~ 1150 hPa)
  • Accuracy: ±1 kPa (at 25°C, 50-105 kPa)
  • Resolution: 0.15 kPa (1.5 hPa)
  • Interface: I2C (up to 400 kHz)
  • Supply Voltage: 2.375V ~ 5.5V
  • Supply Current: 5 µA active (1 sample/s), 1 µA standby
  • Conversion Time: 1 ms typical (pressure), 1 ms (temperature)
  • Internal ADC: 10-bit pressure, 11-bit temperature
  • Calibration: Factory-trimmed coefficients stored in on-chip EEPROM
  • Operating Temperature: -40°C ~ +105°C
  • Package: LGA-8 (3 x 5 x 1.2 mm)

Features

  • Ultra-low power consumption: 5 µA at 1 sample/second
  • Digital I2C output eliminates external ADC
  • Factory-calibrated with on-chip compensation coefficients
  • Integrated temperature sensor for thermal compensation
  • Compact LGA package for space-constrained designs
  • Auto-shutdown between conversions for minimal power

Applications

  • Weather stations and barometric altitude measurement
  • GPS dead reckoning and altitude aiding
  • Smartphones and tablets (weather and floor detection)
  • HVAC systems and indoor navigation
  • Altimeter and variometer for drones
Product Introduction: MPL115A2 Product Introduction

The MPL115A2 from NXP Semiconductors is a compact digital barometer that integrates a MEMS piezoresistive pressure sensor, temperature sensor, ADC, and signal conditioning circuitry in a tiny 3 x 5 x 1.2 mm LGA package. The device provides digital pressure readings via an I2C interface, eliminating the need for external ADC and signal conditioning components. Factory-trimmed calibration coefficients stored in on-chip EEPROM enable the host MCU to compute temperature-compensated pressure values using a simple algorithm. With 5 µA active current at 1 sample/second and 1 µA standby current, the MPL115A2 is ideal for battery-powered applications requiring barometric pressure measurement.

Working Principle: MPL115A2 Working Principle

The MPL115A2 uses a piezoresistive MEMS pressure sensor element whose resistance changes with applied absolute pressure. An internal analog multiplexer alternately connects the pressure sensor and temperature sensor to a high-resolution ADC. The conversion results are stored in registers accessible via the I2C interface. To obtain compensated pressure, the host MCU reads both the raw ADC values and the factory calibration coefficients (a0, b1, b2, c12, c11, c22) from the device, then applies the compensation algorithm specified in the datasheet: Pcomp = a0 + (b1 + c11 * Padc + c12 * Tadc) * Padc + (b2 + c22 * Tadc) * Tadc. The final pressure in kPa is calculated as: Pkpa = Pcomp * (115 – 50) / 1023 + 50. The device automatically powers down between conversions to minimize power consumption.

Pin Description: MPL115A2 Pin Definition and Functions
Pin Name Function
1 SDA I2C Serial Data (bidirectional)
2 GND Ground
3 VDD Power Supply (2.375-5.5V)
4 SCL I2C Serial Clock
5 NC No Connect
6 NC No Connect
7 NC No Connect
8 SHDN Shutdown (active high, pull low for normal operation)
Application Scenarios: In which products and applications is MPL115A2 used

The MPL115A2 is commonly used in weather stations and personal weather monitors where its low cost and digital output simplify design compared to analog pressure sensors. In GPS systems, barometric pressure data improves altitude accuracy beyond what GPS alone can provide, enabling floor-level detection in buildings. For drones, the sensor enables altimeter and variometer functions for altitude hold and navigation. In HVAC systems, it provides absolute pressure data for air flow calculations and building pressure monitoring. The ultra-low power consumption makes it suitable for battery-operated weather stations and wearable altitude trackers.

Alternative Models: What chips are recommended as replacements for MPL115A2
Model Manufacturer Key Difference
MPL3115A2 NXP 20-110 kPa, higher accuracy, altitude mode
BMP280 Bosch 300-1100 hPa, SPI/I2C, higher accuracy
LPS22HB STMicroelectronics 260-1260 hPa, water-resistant

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1