Opens in a new tab

TL494CN

Voltage-mode PWM controller, dual error amps, 300kHz, push-pull/single-ended, 16-PDIP

8595

Effective Inventory

Image for reference only

Manufacturer Part:

TL494CN

Package:

16-PDIP

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TL494CN from Texas Instruments is a fixed-frequency pulse-width-modulation (PWM) control circuit for switching power supplies. With dual error amplifiers, adjustable dead-time, and push-pull or single-ended output, it is the standard controller for PC power supplies and ATX PSU designs. Packaged in 16-PDIP.

Key Specifications

Control Mode Voltage-mode PWM
Switching Frequency 1Hz to 300kHz
Supply Voltage 7V to 40V
Reference Voltage 5V +/-5%
Error Amplifiers 2 (independent)
Output Current 200mA per output
Output Config Push-pull or single-ended
Dead Time Control 0 to 45% adjustable
Package 16-PDIP
Operating Temperature 0 to +70 C

Features

  • Dual error amplifiers for voltage and current feedback
  • Adjustable dead-time control (0-45%)
  • Push-pull or single-ended output configuration
  • Internal 5V reference (5%)
  • Output transistor can source or sink 200mA
  • Under-voltage lockout

Applications

  • ATX and PC power supply controllers
  • Half-bridge and push-pull converters
  • DC-DC converter regulation
  • Battery charger control circuits
Product Introduction: TL494CN Product Introduction

The TL494CN from Texas Instruments is the industry-standard voltage-mode PWM controller used in millions of PC power supplies worldwide. It contains all the building blocks for a switching power supply: an oscillator with frequency set by RT and CT, two error amplifiers for voltage and current feedback, an adjustable dead-time control comparator, a pulse-steering flip-flop for push-pull operation, and two totem-pole output transistors rated at 200mA each. The output configuration pin (pin 13) selects between push-pull (two alternating outputs) and single-ended (parallel outputs). The dead-time control pin (pin 4) provides 0-45% dead-time adjustment, essential for push-pull and half-bridge converters to prevent shoot-through. The internal 5V reference powers the error amplifiers and can supply external circuits. The TL494 has been the backbone of ATX power supply design since the 1990s.

Working Principle: TL494CN Working Principle

The TL494 oscillator generates a sawtooth waveform at the CT pin with frequency determined by RT and CT values (f = 1/(RT x CT)). This sawtooth is compared against three signals in the PWM comparator: the dead-time control voltage (pin 4), the output of error amplifier 1, and the output of error amplifier 2. The PWM comparator outputs a pulse whose width is determined by the lowest of these three control signals. In push-pull mode, the pulse-steering flip-flop alternates the output between the two output transistors (Q1 and Q2) on each oscillator cycle, producing a 50% maximum duty cycle per output. In single-ended mode, both outputs switch in parallel for up to 100% duty cycle. The dead-time control adds a minimum off-time that prevents both output transistors from being on simultaneously in push-pull configurations, ensuring safe operation of the external power switches.

Pin Description: TL494CN Pin Definition and Functions
Pin Name Function
1 1IN+ Error amp 1 non-inverting input
2 1IN- Error amp 1 inverting input
3 FEEDBACK Feedback / PWM compensation
4 DTC Dead-time control (0-45% dead time)
5 CT Oscillator timing capacitor
6 RT Oscillator timing resistor
7 GND Ground
8 C1 Output transistor 1 collector
9 E1 Output transistor 1 emitter
10 E2 Output transistor 2 emitter
11 C2 Output transistor 2 collector
12 VCC Supply voltage (7-40V)
13 OUT CTRL Output control (GND=push-pull, REF=single-ended)
14 REF 5V reference output
15 2IN- Error amp 2 inverting input
16 2IN+ Error amp 2 non-inverting input
Application Scenarios: In which products and applications is TL494CN used
  • ATX PC power supply controller with dual error amplifiers for voltage and current regulation
  • Half-bridge and push-pull converter control with adjustable dead-time
  • DC-DC converter regulation with voltage-mode PWM and 200mA output drive
  • Battery charger control circuits using dual error amplifiers for CV/CC regulation
Alternative Models: What chips are recommended as replacements for TL494CN
Model Manufacturer Key Difference
UC3842BN TI Current-mode, single output, higher performance
KA7500B Fairchild TL494 equivalent, second source
SG3525A ST Push-pull PWM, totem-pole outputs
LM5025 TI Active clamp forward controller, modern

Recommend Parts

BC857BS

Dual PNP transistor, -45V, -100mA, SOT363, Nexperia

Brand: NXP

Package: SOT363 (SC-88, 2.1 x 1.25 x 0.95 mm)

IN STOCK: 8813pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM1200ARZ-RL7

Dual-channel digital isolator based on ADI iCoupler technology, 2/0 direction, SOIC-8 narrow body, 1Mbps (A grade), 2.7-5.5V dual supply, 2500Vrms isolation, >25kV/us CMTI, -40C to +105C.

Package: SOIC-8 Narrow (5.06 x 3.99 x 1.75mm)

IN STOCK: 12476pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PT

MIPS32 MCU, 80MHz, 512KB Flash, Ethernet, dual CAN, USB OTG, 100-TQFP

Brand: MICROCHIP

Package: 100-TQFP (14.0 x 14.0 x 1.0 mm)

IN STOCK: 5670pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IS61WV25616BLL-10TLI

4Mbit async SRAM, 256Kx16, 10ns, 3.3V, 44-TSOP-II Industrial

Brand: Issi

Package: 44-TSOP II

IN STOCK: 7802pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT45DB081E-SHN-T

8Mbit DataFlash, dual-SPI 85MHz, 2x264B SRAM buffers, USON-8 (4x3mm), page-based ECC

Brand: Renesas

Package: USON-8 (4 x 3 x 0.6mm, 0.8mm pitch)

IN STOCK: 4500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TIP35C

NPN power transistor, 100V VCEO, 25A Ic, 125W, TO-247, low saturation voltage, STMicroelectronics

Brand: ST

Package: TO-247 (through-hole, 3-pin)

IN STOCK: 11500pcs

Cargo cycle: 3-7 Days

The minimum order is 1