Opens in a new tab

TDA7388

4x41W class-AB audio amp, BTL, 12V car radio, Flexiwatt-25, diagnostics, mute/standby

6064

Effective Inventory

Image for reference only

Manufacturer Part:

TDA7388

Package:

Flexiwatt-25 (29.40 x 15.10 x 4.50 mm, exposed pad)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TDA7388 from STMicroelectronics is a 4x41W class-AB audio power amplifier in a Flexiwatt-25 package. Designed for car radio applications, it provides four bridge-tied-load (BTL) output channels with diagnostic features and low standby current from a single 12V supply.

Key Specifications

Output Power 4 x 41W (max at 14.4V, 4 Ohm)
Supply Voltage 8 V to 18 V
Output Configuration 4 BTL channels (bridge-tied-load)
THD 0.05% (typical at 1W, 1kHz)
Standby Current 100 uA (max)
Load Impedance 4 Ohm (minimum)
Operating Temperature -40C to +150C

Features

  • 4x41W output power at 14.4V into 4 Ohm BTL loads
  • Class-AB operation with low 0.05% THD at 1W
  • Bridge-tied-load output eliminates output coupling capacitors
  • Built-in diagnostic: clipping, thermal, short circuit, overload
  • Standby and mute functions for power management
  • Flexiwatt-25 package with exposed pad for heatsink mounting

Applications

  • Car radio and automotive head unit audio amplification
  • 4-channel automotive speaker drive systems
  • Marine and recreational vehicle audio systems
  • Multi-room audio distribution amplifiers
Product Introduction: TDA7388 Product Introduction

The TDA7388 from STMicroelectronics is a 4-channel class-AB audio power amplifier in a Flexiwatt-25 surface-mount package, designed primarily for car radio applications. The device provides four bridge-tied-load (BTL) output channels, each capable of delivering up to 41W into a 4 Ohm load at 14.4V supply. The BTL output configuration eliminates the need for large output coupling capacitors, reducing BOM cost and PCB area. The class-AB output stage achieves 0.05% typical THD at 1W output, providing high-quality audio reproduction. Built-in diagnostic features detect clipping, thermal warning, output short circuits, and overload conditions, and report status through a diagnostic pin. The standby function reduces current consumption to below 100uA, while the mute function silences the outputs without entering standby. The device operates from 8V to 18V, covering the full automotive battery voltage range including cold-crank and load-dump conditions. The Flexiwatt-25 package features an exposed thermal pad for direct heatsink attachment.

Working Principle: TDA7388 Working Principle

The TDA7388 uses complementary DMOS output stages in a bridge configuration. (1) Input Stage: Each channel has a differential input that accepts the audio signal. The input impedance is typically 100kOhm, compatible with standard head-unit line-level outputs. AC coupling is required at the input. (2) Voltage Amplifier: A high-gain voltage amplifier stage provides the signal amplification. The gain is internally set to approximately 26dB (20x). (3) Output Stage: Each BTL channel uses two complementary DMOS (double-diffused MOS) output transistors in a push-pull bridge configuration. The bridge drive doubles the voltage swing across the load compared to single-ended output, providing four times the output power for the same supply voltage and load impedance. (4) Diagnostic: A diagnostic comparator monitors output current and junction temperature. When an overload or fault is detected, the DIAG pin is pulled low. The device also reduces output power during thermal warning to prevent damage. (5) Standby/Mute: The STBY pin controls the standby mode (all circuitry disabled, 100uA current). The MUTE pin silences the outputs while keeping the internal bias active for faster unmute recovery.

Pin Description: TDA7388 Pin Definition and Functions
Pin Name Type Function
1-2 OUT3/OUT4 Output Channel 3-4 BTL outputs
3-4 IN3/IN4 Input Channel 3-4 audio inputs
5 MUTE Input Mute control (active low)
6 STBY Input Standby control (active low)
7 DIAG Output Diagnostic output (open-drain)
8 GND Ground Ground
9-10 IN1/IN2 Input Channel 1-2 audio inputs
11-12 OUT1/OUT2 Output Channel 1-2 BTL outputs
13-25 VS/OUT Power/Output Supply and BTL output pairs
Application Scenarios: In which products and applications is TDA7388 used
  • Car radio and automotive head unit 4-channel audio amplification at 41W per channel
  • 4-channel automotive speaker drive systems with BTL and diagnostics
  • Marine and recreational vehicle audio systems operating from 12V battery
  • Multi-room audio distribution amplifiers with mute/standby power management
Alternative Models: What chips are recommended as replacements for TDA7388
Manufacturer Part Number Package Notes
ST TDA7386 Flexiwatt-25 4x45W, higher power
ST TDA7850 Flexiwatt-25 4x50W, MOSFET output
NXP TDF8599C/N2 HSOP-36 4x50W, BTL
TI TAS5414ATPHP HTSSOP-44 4x28W, class-D

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1