Opens in a new tab

M25P16-VMN6TP

16Mbit SPI flash, 75MHz, SOIC-8, 256B page, sector erase, WP/hold, deep power-down

8489

Effective Inventory

Image for reference only

Manufacturer Part:

M25P16-VMN6TP

Package:

SOIC-8 (4.90 x 3.90 x 1.37 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The M25P16-VMN6TP from STMicroelectronics is a 16Mbit (2Mx8) SPI serial flash memory in a SOIC-8 package. With 75MHz SPI clock and 256-byte page programming, it provides reliable non-volatile storage for firmware, configuration, and data logging.

Key Specifications

Memory Size 16 Mbit (2,097,152 x 8 bit)
Interface SPI (0/0 mode, 75 MHz max)
Page Size 256 bytes
Sector/Block 32 sectors (64KB each), 8 blocks (256KB)
Endurance 100,000 erase/write cycles
Data Retention 20 years
Operating Temperature -40C to +85C

Features

  • 16Mbit SPI flash with 75MHz clock for fast firmware access
  • 256-byte page programming in 1.5ms typical
  • Sector (64KB) and bulk erase for flexible data management
  • Write protection with sector lock-down and hardware WP pin
  • Hold pin for pausing serial communication without reset
  • Deep power-down mode with 5uA typical current

Applications

  • Microcontroller firmware and boot code storage
  • FPGA configuration bitstream storage
  • Industrial equipment parameter and calibration data
  • Consumer electronics configuration and log storage
Product Introduction: M25P16-VMN6TP Product Introduction

The M25P16-VMN6TP from STMicroelectronics is a 16Mbit (2M x 8) serial flash memory with SPI interface in a SOIC-8 package. The device supports SPI clock frequencies up to 75MHz, providing fast read throughput for firmware execution and data access. The memory is organized as 32 sectors of 64KB each, with 256-byte page programming capability. Page programming time is typically 1.5ms, and sector erase time is typically 1 second. The device supports multiple read modes including standard read, fast read, and dual output fast read for increased bandwidth. Write protection features include individual sector lock-down, hardware write protect (W) pin, and write-enable latch that must be set before any write or erase operation. The hold (HOLD) pin allows the SPI communication to be paused without resetting the device, useful for shared SPI bus applications. Deep power-down mode reduces current consumption to 5uA typical for battery-powered applications. The 100,000 erase/write cycle endurance and 20-year data retention provide long-term reliability.

Working Principle: M25P16-VMN6TP Working Principle

The M25P16-VMN6TP uses NOR flash memory with SPI serial interface. (1) Memory Array: The 16Mbit storage is organized as 2,097,152 bytes in 32 sectors of 65,536 bytes (64KB) each. Each sector contains 256 pages of 256 bytes. (2) SPI Protocol: Commands, addresses, and data are transferred serially via the SPI bus (S, Q, D, C pins). The device supports SPI mode 0 (CPOL=0, CPHA=0) and mode 3. Commands are 1 byte, addresses are 24 bits (3 bytes). (3) Read: The READ command outputs data starting at the specified address. FAST_READ reduces the access time by using a dummy clock cycle. Dual output mode uses both Q and D pins for 2x throughput. (4) Program: Page programming writes up to 256 bytes in one operation. The WREN (write enable) command must be issued before programming. Data is first written to an internal buffer, then programmed to the flash array. (5) Erase: Sector erase clears one 64KB sector to all 1s. Bulk erase clears the entire array. Erase operations also require WREN. (6) Protection: The status register provides write protection through block protect bits (BP1, BP2) that define protected address ranges. The W pin provides hardware write protection when low.

Pin Description: M25P16-VMN6TP Pin Definition and Functions
Pin Name Type Function
1 S Input Chip select (active low)
2 Q Output Data output (MISO)
3 W Input Write protect (active low)
4 VSS Ground Ground
5 D Input Data input (MOSI)
6 C Input SPI clock
7 HOLD Input Hold (pauses serial communication)
8 VDD Power Supply (2.7V to 3.6V)
Application Scenarios: In which products and applications is M25P16-VMN6TP used
  • Microcontroller firmware and boot code storage at 75MHz SPI
  • FPGA configuration bitstream storage with fast read
  • Industrial equipment parameter and calibration data with sector protection
  • Consumer electronics configuration and log storage with 20-year retention
Alternative Models: What chips are recommended as replacements for M25P16-VMN6TP
Manufacturer Part Number Package Notes
ST M25P32-VMF6TP SOIC-8 32Mbit, same family
Macronix MX25L1606EM2I-12G SOIC-8 16Mbit, 120MHz, equivalent
Winbond W25Q16JVSSIQ SOIC-8 16Mbit, 133MHz, dual/quad
Microchip SST25VF016B-50-4I-S2AF SOIC-8 16Mbit, 50MHz

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1