Opens in a new tab

TLV75533PDBVR

500mA LDO, 3.3V fixed, 46dB PSRR, 35uA IQ, SOT-23-5, active discharge, 1uF Cmin

10613

Effective Inventory

Image for reference only

Manufacturer Part:

TLV75533PDBVR

Package:

SOT-23-5 (2.90 x 1.60 x 1.00 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The TLV75533PDBVR from Texas Instruments is a 500mA low-IQ low-dropout regulator with 3.3V fixed output in a SOT-23-5 package. With 46dB PSRR at 100kHz and 1uF minimum output capacitor, it provides clean power for noise-sensitive circuits.

Key Specifications

Output Voltage 3.3 V (fixed)
Output Current 500 mA (max)
Input Voltage 1.45 V to 5.5 V
Dropout Voltage 200 mV (typ at 500mA)
PSRR 46 dB at 100kHz
IQ 35 uA (typical)
Operating Temperature -40C to +125C

Features

  • 3.3V fixed output at 500mA with 200mV typical dropout
  • 46dB PSRR at 100kHz for noise-sensitive RF and analog circuits
  • 35uA low quiescent current for battery-powered applications
  • 1uF minimum ceramic output capacitor for stable operation
  • Active discharge feature for controlled output capacitor discharge
  • Enable pin with 10kHz toggle capability for power sequencing

Applications

  • Post-regulation for switch-mode power supplies
  • RF and wireless module power supply
  • Battery-powered IoT sensor node regulation
  • Portable electronics and wearable devices
Product Introduction: TLV75533PDBVR Product Introduction

The TLV75533PDBVR from Texas Instruments is a 500mA, low-quiescent-current, low-dropout (LDO) linear regulator with a fixed 3.3V output in a SOT-23-5 package. The device features a 200mV typical dropout voltage at 500mA load, enabling efficient regulation from a 3.6V lithium cell or 3.3V rail with minimal headroom. The 46dB PSRR at 100kHz effectively rejects switching power supply ripple, making it ideal for post-regulation of DC-DC converters feeding noise-sensitive RF and analog circuits. The 35uA typical quiescent current minimizes battery drain in always-on applications. The LDO requires only a 1uF ceramic output capacitor for stability, simplifying PCB layout and reducing BOM cost. An active output discharge feature ensures controlled discharge of the output capacitor when the regulator is disabled, preventing residual voltage that could cause malfunction during power cycling. The enable pin supports toggling up to 10kHz for power sequencing or load switching applications. The device operates over the -40C to +125C junction temperature range and includes thermal shutdown and overcurrent protection.

Working Principle: TLV75533PDBVR Working Principle

The TLV75533PDBVR uses a PMOS pass transistor to regulate the output voltage. (1) Regulation: A voltage divider at the output (internal for fixed-voltage versions) provides feedback to the error amplifier. The error amplifier compares the feedback voltage to an internal 0.6V reference and drives the PMOS gate to maintain the output at 3.3V. When the output drops below 3.3V, the error amplifier increases the gate drive, reducing the PMOS on-resistance and increasing output current. (2) Dropout: The PMOS pass element requires only a small VGS to maintain regulation, resulting in the 200mV typical dropout voltage. Below the minimum input voltage (VOUT + VDO), the PMOS is fully enhanced and the output follows the input minus the IR drop. (3) PSRR: The high open-loop gain of the error amplifier provides 46dB of power supply rejection at 100kHz, attenuating input ripple before it reaches the output. At higher frequencies, the PSRR decreases as the loop gain rolls off. (4) Active Discharge: When the enable pin is driven low, an internal pull-down resistor (approximately 250 ohm) is connected across the output, discharging the output capacitor in a controlled manner. This prevents the output from floating at an indeterminate voltage.

Pin Description: TLV75533PDBVR Pin Definition and Functions
Pin Name Type Function
1 OUT Output Regulated 3.3V output
2 GND Ground Ground
3 EN Input Enable (active high)
4 NC – Not connected
5 IN Power Input supply (1.45-5.5V)
Application Scenarios: In which products and applications is TLV75533PDBVR used
  • Post-regulation for switch-mode power supplies with 46dB PSRR
  • RF and wireless module 3.3V power supply at 500mA
  • Battery-powered IoT sensor node regulation with 35uA IQ
  • Portable electronics and wearable devices with 1uF capacitor
Alternative Models: What chips are recommended as replacements for TLV75533PDBVR
Manufacturer Part Number Package Notes
TI TLV74333PDBVR SOT-23-5 Higher PSRR, 1A
TI TLV75518PDBVR SOT-23-5 1.8V output version
Microchip MIC5219-3.3YM5-TR SOT-23-5 500mA, 3.3V, similar
Diodes Inc AP2112K-3.3TRG1 SOT-23-5 600mA, 3.3V, low IQ

Recommend Parts

BC857BS

Dual PNP transistor, -45V, -100mA, SOT363, Nexperia

Brand: NXP

Package: SOT363 (SC-88, 2.1 x 1.25 x 0.95 mm)

IN STOCK: 8813pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM1200ARZ-RL7

Dual-channel digital isolator based on ADI iCoupler technology, 2/0 direction, SOIC-8 narrow body, 1Mbps (A grade), 2.7-5.5V dual supply, 2500Vrms isolation, >25kV/us CMTI, -40C to +105C.

Package: SOIC-8 Narrow (5.06 x 3.99 x 1.75mm)

IN STOCK: 12476pcs

Cargo cycle: 3-7 Days

The minimum order is 1

PIC32MX795F512L-80I/PT

MIPS32 MCU, 80MHz, 512KB Flash, Ethernet, dual CAN, USB OTG, 100-TQFP

Brand: MICROCHIP

Package: 100-TQFP (14.0 x 14.0 x 1.0 mm)

IN STOCK: 5670pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IS61WV25616BLL-10TLI

4Mbit async SRAM, 256Kx16, 10ns, 3.3V, 44-TSOP-II Industrial

Brand: Issi

Package: 44-TSOP II

IN STOCK: 7802pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AT45DB081E-SHN-T

8Mbit DataFlash, dual-SPI 85MHz, 2x264B SRAM buffers, USON-8 (4x3mm), page-based ECC

Brand: Renesas

Package: USON-8 (4 x 3 x 0.6mm, 0.8mm pitch)

IN STOCK: 4500pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TIP35C

NPN power transistor, 100V VCEO, 25A Ic, 125W, TO-247, low saturation voltage, STMicroelectronics

Brand: ST

Package: TO-247 (through-hole, 3-pin)

IN STOCK: 11500pcs

Cargo cycle: 3-7 Days

The minimum order is 1