Opens in a new tab

VNS3NV04DPTR-E

30V 3A high-side switch, 80mOhm, SO-8, VIPower, automotive protections, diagnostic

5983

Effective Inventory

Image for reference only

Manufacturer Part:

VNS3NV04DPTR-E

Package:

SO-8 (5.00 x 4.00 x 1.75 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The VNS3NV04DPTR-E from STMicroelectronics is a VIPower M0-3 single-channel high-side power switch in a SO-8 package. With 30V/3A rating and 80mOhm RDS(on), it provides protected power switching for automotive and industrial loads.

Key Specifications

Supply Voltage 4.5 V to 28 V (36V transient)
Output Current 3 A (continuous)
RDS(on) 80 mOhm (typical)
Channels 1 (single high-side)
Protections Over-temp, over-current, short circuit, ESD
Operating Temperature -40C to +150C

Features

  • 80mOhm low RDS(on) for minimal voltage drop at 3A
  • Comprehensive protection: thermal, overcurrent, short circuit, ESD
  • Open-drain diagnostic status output for fault detection
  • CMOS-compatible input with hysteresis for noise immunity
  • Undervoltage lockout prevents incomplete turn-on
  • AEC-Q100 qualified for automotive applications

Applications

  • Automotive lamp and solenoid driver
  • Industrial relay and heater switching
  • Distributed power distribution in vehicle body electronics
  • Building automation load switching
Product Introduction: VNS3NV04DPTR-E Product Introduction

The VNS3NV04DPTR-E from STMicroelectronics is a monolithic single-channel high-side power switch using VIPower M0-3 technology in an SO-8 package. The device integrates a 30V N-channel power MOSFET with 80mOhm typical RDS(on) and all necessary control and protection circuitry. The 3A continuous output current rating supports a wide range of automotive and industrial loads including lamps, solenoids, relays, and heaters. Comprehensive protection features include thermal shutdown with automatic restart, current limitation with short-circuit protection, undervoltage lockout, and reverse battery protection. An open-drain diagnostic status output indicates fault conditions (overtemperature, overload, or open load) to the system MCU, enabling intelligent fault management. The CMOS-compatible input with hysteresis provides noise immunity in automotive environments. The device is AEC-Q100 qualified and supports 36V transient input voltage for load dump protection. The SO-8 package provides adequate thermal dissipation for the 3A rating with a thermal shutdown threshold at 150C typical.

Working Principle: VNS3NV04DPTR-E Working Principle

The VNS3NV04DPTR-E uses a vertical power MOSFET with integrated control and protection. (1) High-Side Switch: The N-channel power MOSFET is connected between the supply (VCC) and the output (OUT). When the input (IN) is driven high, the charge pump generates a gate voltage above VCC to fully enhance the MOSFET, connecting VCC to OUT. When IN is low, the MOSFET turns off, disconnecting the load. (2) Charge Pump: An internal charge pump generates the gate drive voltage above the supply rail, enabling the use of N-channel MOSFETs for lower RDS(on) compared to P-channel alternatives. (3) Current Limit: If the output current exceeds the limit (typically 5-10A), the current limit circuit reduces the gate drive to regulate the current, preventing MOSFET damage. (4) Thermal Protection: A temperature sensor monitors the die temperature. If it exceeds approximately 150C, the MOSFET is turned off. When the die cools below the hysteresis threshold, the device automatically restarts. (5) Diagnostic: The status output is pulled low when a fault is detected (overtemperature or current limit active), providing real-time fault indication to the MCU.

Pin Description: VNS3NV04DPTR-E Pin Definition and Functions
Pin Name Type Function
1 OUT Output Power output to load
2 VCC Power Supply input (4.5-28V)
3 GND Ground Ground
4 IN Input Logic input (CMOS compatible)
5 STATUS Output Diagnostic output (open-drain)
Application Scenarios: In which products and applications is VNS3NV04DPTR-E used
  • Automotive lamp and solenoid driver with diagnostic status output
  • Industrial relay and heater switching with 80mOhm RDS(on)
  • Distributed power distribution in vehicle body electronics at AEC-Q100
  • Building automation load switching with thermal and short-circuit protection
Alternative Models: What chips are recommended as replacements for VNS3NV04DPTR-E
Manufacturer Part Number Package Notes
ST VND5N07-E SO-8 Similar, different RDS(on)
Infineon BTS4140N SOT-223 Single high-side, 40V
TI TPS1H100AQPWPRQ1 HTSSOP-20 Automotive, 1A, more features
NXP MC33991DW SO-20 4-channel high-side

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1