Opens in a new tab

LP2951ACMX

100mA LDO, 380mV dropout, 75uA Iq, adj 1.24-29V, error flag, VSSOP-8

9500

Effective Inventory

Image for reference only

Manufacturer Part:

LP2951ACMX

Package:

VSSOP-8 (3.00 x 3.00 x 0.90 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The LP2951ACMX from Texas Instruments (formerly National Semiconductor) is a micropower low-dropout voltage regulator with 100mA output, 380mV dropout at 100mA, programmable output (1.24-29V), and error flag in an 8-pin VSSOP package.

Key Specifications

Output Voltage Adjustable (1.24 V to 29 V)
Output Current 100 mA
Dropout Voltage 380 mV @ 100mA
Quiescent Current 75 uA typical (no load)
Load Regulation 0.05% typical
Line Regulation 0.03% typical
Output Noise 100 uV RMS (10Hz-100kHz)
Shutdown Yes (logic level)
Error Flag Yes (output undervoltage)
Reference Voltage 1.235V
Input Voltage 2.0 V to 30 V
Operating Temperature -40°C to +125°C
Package VSSOP-8 (3.0×3.0mm)

Features

  • 100mA LDO with 380mV dropout and 75uA quiescent current
  • Adjustable output from 1.24V to 29V with 1.235V internal reference
  • Error flag output indicates output undervoltage condition
  • Logic-level shutdown for power management control

Applications

  • Battery-powered instrumentation and portable electronics LDO
  • High-efficiency post-regulation after switching converters
Product Introduction: LP2951ACMX Product Introduction

The LP2951ACMX from Texas Instruments is a micropower low-dropout voltage regulator designed for battery-powered applications. The device provides up to 100mA output current with only 380mV dropout voltage at full load, enabling efficient operation from batteries down to end-of-life voltage. The quiescent current is a very low 75uA with no load, and the device maintains regulation with only 1uA load. The output voltage is adjustable from 1.24V to 29V using an external resistor divider, referenced to an internal 1.235V bandgap. An error flag output (open-collector) asserts when the output drops below approximately 92% of the nominal voltage, providing early warning of power failure or brownout. A logic-level shutdown pin reduces quiescent current to near zero when the regulator is disabled. The AC version provides tighter initial accuracy (+/-0.5%) than the standard LP2951. The CMX suffix denotes the VSSOP-8 package on tape and reel.

Working Principle: LP2951ACMX Working Principle

The LP2951ACMX operates as a PNP-based low-dropout linear voltage regulator. (1) PNP Pass Transistor: Unlike NPN-based regulators that require the input voltage to be at least 1.5-2V above the output (VBE + VCE(sat) + Vdrop), the PNP pass transistor only requires VCE(sat) dropout, typically 380mV at 100mA. This allows operation with much smaller input-to-output voltage differential, critical for battery-powered applications. (2) Bandgap Reference: The internal 1.235V bandgap reference is compared with the feedback voltage from the output divider. The error amplifier adjusts the base drive of the PNP pass transistor to maintain regulation. (3) Error Flag: A voltage comparator monitors the output voltage. When the output drops below approximately 92% of the set value (due to overload, low input, or thermal shutdown), the error flag output pulls low through an open-collector NPN transistor. This provides an early warning for system power-fail detection. (4) Shutdown: The TTL/CMOS-compatible shutdown pin controls the regulator. When the shutdown pin is pulled high, the PNP pass transistor is turned off, reducing the supply current to near zero.

Pin Description: LP2951ACMX Pin Definition and Functions
Pin Name Function
1 VOUT Regulated output (up to 100mA)
2 SENSE Feedback sense (connect to VOUT)
3 SHDN Shutdown (high = off)
4 GND Ground
5 ERR Error flag output (open-collector)
6 TAP Output voltage tap (internal divider)
7 FB Feedback input (external divider)
8 VIN Input supply (2.0-30V)
Application Scenarios: In which products and applications is LP2951ACMX used
  • Battery-powered instrumentation LDO with 380mV dropout and error flag
  • Post-regulation after switching converter with 75uA Iq
Alternative Models: What chips are recommended as replacements for LP2951ACMX
Manufacturer Part Number Package Notes
TI LP2951ACMX/NOPB VSSOP-8 NOPB = non-braided packaging
TI LP2950CDT-3.3RG4 SOT-223 Fixed 3.3V, 100mA, 3-pin
Microchip TC1185-3.3VCT713 SOT-23-5 150mA LDO, smaller

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1