Opens in a new tab

AT24C256D-SSHL-T

256Kb I2C EEPROM, 1MHz, 1.7-5.5V, 64-byte page, 1M cycles, TSSOP-8

23790

Effective Inventory

Image for reference only

Manufacturer Part:

AT24C256D-SSHL-T

Package:

TSSOP-8 (4.4 x 3.0 x 1.0mm, 0.65mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The AT24C256D-SSHL-T is a 256Kb I2C serial EEPROM from Microchip Technology with 1MHz clock, 64-byte page write, 1M cycle endurance, and 100-year data retention in a TSSOP-8 package.

Key Specifications

Memory Size 256 Kbit (32,768 x 8)
Interface I2C (2-wire serial)
Max Clock Frequency 1 MHz (High-Speed mode)
Supply Voltage 1.7V to 5.5V
Page Write Size 64 bytes
Write Cycle Time 5ms typical
Write Endurance 1,000,000 cycles
Data Retention 100 years (D revision)
Address Pins 3 (A0, A1, A2) for up to 8 devices on bus
Write Protect Hardware WP pin (full array protection)
Input Type Schmitt-trigger (noise suppression)
Operating Temperature -40°C to +85°C
Package TSSOP-8 (4.4 x 3.0mm)

Features

  • 256Kbit (32K x 8) organization with 64-byte page write buffer
  • I2C compatible: Standard (100kHz), Fast (400kHz), High-Speed (1MHz)
  • Wide operating voltage: 1.7V to 5.5V
  • Schmitt-trigger inputs for noise suppression
  • Hardware write protect pin for full array protection
  • 3 address pins allow up to 8 devices on one I2C bus (2Mbit total)
  • 1 million write cycle endurance
  • 100-year data retention (D revision improved from 40 years)
  • Self-timed write cycle with auto-erase
  • Output slope control to eliminate ground bounce

Applications

  • Embedded system configuration storage
  • Industrial data logging
  • Automotive ECU parameter storage
  • Consumer electronics settings retention
  • IoT device calibration and state data
Product Introduction: AT24C256D-SSHL-T Product Introduction

The AT24C256D-SSHL-T from Microchip Technology is a 256Kbit (32,768 x 8) I2C-compatible serial EEPROM with enhanced data retention of 100 years in the D revision. The device supports Standard (100kHz), Fast (400kHz), and High-Speed (1MHz) I2C modes. A 64-byte page write buffer allows efficient writing of up to 64 bytes in a single write cycle, with 5ms self-timed write completion. Schmitt-trigger inputs on SCL and SDA suppress electrical noise for reliable communication in industrial environments. Three address pins (A0, A1, A2) enable up to eight AT24C256D devices on the same I2C bus, providing up to 2Mbit of addressable memory. The hardware Write Protect (WP) pin protects the entire memory array from accidental writes. The SSHL-T suffix denotes the TSSOP-8 package with tape-and-reel packaging.

Working Principle: AT24C256D-SSHL-T Working Principle

The AT24C256D-SSHL-T communicates via the I2C protocol using just two signal lines: SCL (serial clock) and SDA (serial data). The master initiates communication by sending a START condition (SDA transitions from high to low while SCL is high), followed by the device address byte. The upper 4 bits are the fixed device identifier (1010), the next 3 bits match the hardware address pins (A2, A1, A0), and the LSB is the Read/Write bit. For a write operation, the master sends two address bytes (A15-A8, A7-A0) to specify the memory location, then up to 64 data bytes. The internal address counter auto-increments within the 64-byte page boundary; if the counter reaches the page end, it wraps to the beginning of the same page (not the next page). The master sends a STOP condition to initiate the internal write cycle. During the 5ms write cycle, the device does not acknowledge any I2C communication, which can be used for polling (ACK polling) to detect write completion. For a read operation, the master first writes the address (dummy write), then sends a repeated START with the R/W bit set to read. The device outputs data bytes and the internal address counter increments across page boundaries for sequential reads. The WP pin, when tied to VCC, prevents any write operation to the entire array. Schmitt-trigger inputs on SCL and SDA provide hysteresis that rejects noise spikes below the Schmitt threshold.

Pin Description: AT24C256D-SSHL-T Pin Definition and Functions
Pin Name Type Description
1 A0 Input Address input 0 (set to VSS or VDD for bus address)
2 A1 Input Address input 1 (set to VSS or VDD for bus address)
3 A2 Input Address input 2 (set to VSS or VDD for bus address)
4 VSS Power Ground
5 SDA I/O Serial data (open-drain, requires pull-up resistor)
6 SCL Input Serial clock (Schmitt-trigger input)
7 WP Input Write Protect (VCC = protect all, VSS = normal R/W)
8 VCC Power Supply (1.7V to 5.5V)
Application Scenarios: In which products and applications is AT24C256D-SSHL-T used
  • Embedded Config: 256Kbit stores multiple configuration profiles, calibration tables, and firmware parameters with 100-year retention across power cycles
  • Industrial Data Log: 1MHz High-Speed mode reads logged data quickly; Schmitt-trigger inputs tolerate noisy factory environments
  • Automotive: 1.7V min supply compatible with battery-cranking dips; WP pin prevents ECU parameter corruption
  • IoT Devices: 8 devices on one I2C bus provides 2Mbit for firmware, keys, and device state without additional chip-select lines
  • Consumer Electronics: 5V and 3.3V compatible with no external level shifters; small TSSOP-8 fits in compact consumer designs
Alternative Models: What chips are recommended as replacements for AT24C256D-SSHL-T
Model Manufacturer Key Difference Package Specs
AT24C512C-SSHL-T Microchip 512Kbit (64Kx8), same pinout, 128-byte page – –
AT24C128D-SSHL-T Microchip 128Kbit (16Kx8), same pinout – –
24LC256-I/SN Microchip 256Kb, 400kHz max, SOIC-8, 40yr retention – –
BR24G256FVT-WE2 Rohm 256Kbit I2C, TSSOP-8, equivalent – –
M24256-DFMN6TP ST 256Kbit I2C EEPROM, TSSOP-8 – –

AT24C256D-SSHL-T is a 256Kbit (32768×8) I2C EEPROM from Microchip in TSSOP-8. The AT24C512D doubles density to 512Kbit in the same package. The AT24CM01 provides 1Mbit for maximum storage. The CAT24C256WI-GT3 from onsemi offers 256Kbit with hardware write protect. The M24256 from ST provides similar 256Kbit with WC pin. The 24AA256 from Microchip offers 1.7V minimum supply for low-voltage designs. For higher endurance, FM24CL16B from Cypress provides 256Kbit FRAM with 100 trillion write cycles.

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1