Opens in a new tab

LM317T

1.5A adj positive regulator, 1.25-37V out, 80dB PSRR, TO-220-3

25000

Effective Inventory

Image for reference only

Manufacturer Part:

LM317T

Package:

TO-220-3 (14.986 x 10.16 x 4.6mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM317T is a 1.5A adjustable positive linear voltage regulator from Texas Instruments, providing output from 1.25V to 37V with only two external resistors, in a TO-220-3 through-hole package.

Key Specifications

Output Voltage Range 1.25V to 37V (adjustable)
Output Current 1.5A (max)
Input Voltage Range 4.25V to 40V
Line Regulation 0.01%/V typical
Load Regulation 0.1% typical
Ripple Rejection 80dB (120Hz)
Reference Voltage 1.25V (between OUT and ADJ)
Dropout Voltage 3V typical (VI-VO minimum)
Thermal Overload Protection Yes
Short-Circuit Protection Yes (current limit constant with temperature)
Safe Operating Area Protection Yes
Operating Temperature 0°C to +125°C
Package TO-220-3 (14.986 x 10.16mm, through-hole)

Features

  • Adjustable output from 1.25V to 37V with two external resistors
  • 1.5A output current capability
  • 0.1% typical load regulation
  • 0.01%/V typical line regulation
  • 80dB ripple rejection at 120Hz
  • Thermal overload, short-circuit, and SOA protection
  • Floating architecture for high-voltage regulation
  • Can be used as a precision current regulator
  • Electronic shutdown by clamping ADJ to ground

Applications

  • Adjustable bench power supplies
  • Battery chargers and charging circuits
  • Current regulator for LED strings
  • Local on-card regulation
  • High-voltage regulators (floating operation)
Product Introduction: LM317T Product Introduction

The LM317T from Texas Instruments is a classic adjustable 3-terminal positive voltage regulator capable of supplying more than 1.5A over an output range of 1.25V to 37V. It requires only two external resistors to set the output voltage: VOUT = 1.25V × (1 + R2/R1) + IADJ × R2, where IADJ is typically 50µA. The device offers superior line and load regulation compared to fixed regulators (0.01%/V and 0.1% typical, respectively) and 80dB ripple rejection. Full overload protection includes current limiting, thermal shutdown, and safe operating area protection—all of which remain functional even if the ADJ pin is accidentally disconnected. The floating architecture means the regulator only sees the input-to-output differential voltage, allowing it to regulate supplies of several hundred volts as long as the differential does not exceed 40V. The T suffix denotes the TO-220-3 through-hole package, ideal for heatsink mounting.

Working Principle: LM317T Working Principle

The LM317T maintains a constant 1.25V reference between the OUT and ADJ pins. Current flowing through R1 (connected between OUT and ADJ) is I_R1 = 1.25V / R1. This same current (plus the small IADJ of ~50µA) flows through R2 (connected between ADJ and GND), setting the output voltage: VOUT = 1.25V × (1 + R2/R1) + IADJ × R2. For practical purposes, IADJ × R2 is negligible, so VOUT ≈ 1.25V × (1 + R2/R1). A typical design uses R1 = 240Ω, giving I_R1 ≈ 5.2mA. The output voltage is then set by R2: for 5V output, R2 ≈ 720Ω; for 12V, R2 ≈ 2.06kΩ; for 3.3V, R2 ≈ 394Ω. The minimum load current is approximately 3.5mA (the internal reference current), so R1 should not exceed approximately 375Ω to guarantee regulation under no-load conditions. The input-to-output differential voltage must be at least 3V (dropout voltage) for proper regulation, meaning VIN must be at least VOUT + 3V. The internal current limit is typically 2.2A at 25°C, and it remains relatively constant over temperature. The thermal shutdown activates at approximately 170°C junction temperature. The ADJ pin can be bypassed with a 10µF capacitor to improve ripple rejection to over 80dB.

Pin Description: LM317T Pin Definition and Functions
Pin Name Type Description
1 ADJ Input Adjust pin (connect R1 to OUT, R2 to GND)
2 OUT Output Regulated output voltage (1.25V to 37V)
3 IN Input Unregulated input voltage (4.25V to 40V)

LM317T uses the TO-220-3 package with adjustable regulator pinout: Pin 1 = ADJ (Adjustment), Pin 2 = VOUT (tab), Pin 3 = VIN. This pinout differs from fixed 78xx regulators where Pin 1 = INPUT. The tab is electrically connected to VOUT (Pin 2), not GND — this is critical for heatsink mounting. When VOUT is not at ground potential, an insulating washer is required between tab and heatsink. The ADJ pin maintains 1.25V below VOUT with 50µA bias current. Output voltage is set by R1 (VOUT to ADJ, typically 240Ω) and R2 (ADJ to GND). Protection diodes are recommended: D1 (1N4002, ADJ to VOUT) for output capacitors >10µF, and D2 (1N5400, VIN to VOUT) for reverse input conditions.

Application Scenarios: In which products and applications is LM317T used
  • Adjustable Bench PSU: Replace R2 with a 5kΩ potentiometer for 1.25V–26V adjustable output; add 10µF cap on ADJ for clean output
  • Battery Charger: Set VOUT to float voltage (e.g., 13.8V for 12V lead-acid); add series diode and current-limiting resistor
  • LED Current Regulator: Connect ADJ to load (LED cathode) with R1 setting ILED = 1.25V / R1; e.g., R1=12.5Ω gives 100mA
  • High-Voltage Regulation: Floating topology allows regulating 100V+ rails; only VI-VO differential must stay under 40V
  • Electronic Shutdown: Drive ADJ to GND with a transistor; VOUT drops to 1.25V where most loads draw negligible current
Alternative Models: What chips are recommended as replacements for LM317T
Model Manufacturer Key Difference Package Specs
LM317AT onsemi Tighter reference voltage tolerance ±1% vs ±4% for precision adjustable power supplies TO-220-3 1.25-37V/1.5A
LM317EMP/NOPB TI SOT-223 surface-mount version for compact board designs with 1A output current SOT-223-4 1.25-37V/1A
LM317DCYT/NOPB TI SOT-223-3 with TO-263 compatibility and lower dropout for space-constrained designs SOT-223-3 1.25-37V/1A
LM337T TI Negative adjustable complement: -1.25V to -37V for symmetric split-rail power supplies TO-220-3 -1.25 to -37V/1.5A
LM1117MP-3.3 TI Lower dropout (1.1V) fixed 3.3V alternative for regulated 3.3V logic supply rails SOT-223-4 3.3V/800mA LDO
LM1085IT-5.0 TI 3A higher-current adjustable LDO for applications requiring more than 1.5A output TO-220-3 1.25-37V/3A

LM317T is a 1.25-37V adjustable positive voltage regulator in TO-220-3 with 1.5A output and ±4% reference tolerance. The LM317AT offers ±1% precision. For surface-mount, use LM317EMP (SOT-223). For higher current, LM1085 provides 3A output. The LM337T is the negative complement for split-rail supplies. All require only two external resistors to set output voltage.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1