Opens in a new tab

NE5532P

Dual low-noise op-amp, 5nV/√Hz, 10MHz GBW, 9V/µs, PDIP-8

8500

Effective Inventory

Image for reference only

Manufacturer Part:

NE5532P

Package:

PDIP-8 (9.81 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The NE5532P from Texas Instruments is a dual low-noise operational amplifier with 5nV/√Hz input noise, 10MHz gain-bandwidth, 9V/µs slew rate, and 100dB CMRR, making it the industry-standard choice for professional and consumer audio applications in a PDIP-8 package.

Key Specifications

Number of Channels 2 (dual)
Supply Voltage Range ±5V to ±15V (10V to 30V total)
Input Noise Voltage (en) 5nV/√Hz typical @ 1kHz
Gain-Bandwidth Product 10MHz typical
Slew Rate 9V/µs typical
Common-Mode Rejection Ratio 100dB typical
DC Voltage Gain 100V/mV (100dB) typical
Output Voltage Swing ±13V typical @ ±15V, RL=600Ω
Output Current 38mA typical per channel
Input Offset Voltage 4mV max @ 25°C
Input Bias Current 800nA max
THD+N 0.002% typical @ 1kHz
Supply Current 4mA typical per channel
Operating Temperature 0°C to +70°C
Package PDIP-8 (9.81 x 6.35mm)

Features

  • Ultra-low input noise: 5nV/√Hz at 1kHz
  • High gain-bandwidth product: 10MHz
  • High slew rate: 9V/µs
  • Very low THD+N: 0.002% at 1kHz
  • 100dB CMRR for excellent noise rejection
  • High output drive: 38mA per channel, drives 600Ω loads
  • Internal unity-gain compensation
  • Input protection diodes
  • Output short-circuit protection
  • Industry-standard 5532 pinout

Applications

  • Professional audio mixers and preamps
  • AV receivers and hi-fi amplifiers
  • Equalizer and crossover networks
  • Line drivers and receivers
  • Active filter circuits
Product Introduction: NE5532P Product Introduction

The NE5532P from Texas Instruments is the industry-standard dual low-noise operational amplifier, renowned for its 5nV/√Hz equivalent input noise voltage at 1kHz—among the lowest of any bipolar op-amp in its class. With a 10MHz gain-bandwidth product and 9V/µs slew rate, it handles audio bandwidth with ample margin. The 100dB CMRR and 0.002% THD+N at 1kHz ensure pristine signal quality in professional audio applications. The 38mA output drive capability per channel allows it to directly drive 600Ω balanced lines without buffering. The device is internally compensated for unity-gain stability, simplifying circuit design. The bipolar input stage provides lower voltage noise than CMOS alternatives, though at the cost of higher input bias current (800nA max). The NE5532 has been the go-to audio op-amp for decades, used in mixing consoles, preamplifiers, equalizers, and hi-fi equipment worldwide. The P suffix denotes the PDIP-8 through-hole package.

Working Principle: NE5532P Working Principle

The NE5532P consists of two independent high-performance operational amplifiers on a single die. Each amplifier uses a bipolar input stage with a differential pair, providing the low voltage noise (5nV/√Hz) that is the hallmark of this device. The input stage feeds a voltage gain stage with active current-mirror load, followed by a class-AB output stage capable of sourcing and sinking 38mA. Internal compensation capacitance ensures stability at unity gain without external components. The input protection diodes clamp excessive differential input voltages, and the output stage has short-circuit protection that limits output current during fault conditions. In a typical audio preamp application, the non-inverting input receives the audio signal, and the feedback network from output to inverting input sets the closed-loop gain. At audio frequencies, the open-loop gain of 100dB (100V/mV) provides abundant loop gain for low-distortion amplification. At 1kHz with 20dB (×10) closed-loop gain, the loop gain is approximately 80dB, meaning distortion is reduced by a factor of 10,000 from the open-loop value, resulting in the measured 0.002% THD+N.

Pin Description: NE5532P Pin Definition and Functions
Pin Name Type Description
1 OUT A Output Amplifier A output
2 IN- A Input Amplifier A inverting input
3 IN+ A Input Amplifier A non-inverting input
4 V- Power Negative supply (e.g., -15V)
5 IN+ B Input Amplifier B non-inverting input
6 IN- B Input Amplifier B inverting input
7 OUT B Output Amplifier B output
8 V+ Power Positive supply (e.g., +15V)

NE5532P uses the PDIP-8 package with standard dual op-amp pinout: Pin 1 = Output A, Pin 2 = Inverting Input A (-), Pin 3 = Non-inverting Input A (+), Pin 4 = VEE (-V), Pin 5 = Non-inverting Input B (+), Pin 6 = Inverting Input B (-), Pin 7 = Output B, Pin 8 = VCC (+V). This is the same pinout as LM358, TL072, and RC4558. The NE5532 differs from LM358 in requiring dual supplies (±3V to ±22V) and providing superior audio performance with 5nV/√Hz input noise density. The output can drive 600Ω loads directly. For surface-mount, NE5532DR (SOIC-8) provides identical pinout. The NE5532AP is the premium-grade version with tighter noise and offset specifications.

Application Scenarios: In which products and applications is NE5532P used
  • Audio Preamp: Non-inverting gain stage for microphone or line-level; 5nV/√Hz noise preserves dynamic range below -100dBu
  • RIAA Phono Stage: Two-stage equalizer with feedback RIAA network; low noise critical for cartridge signals
  • Active Crossover: Linkwitz-Riley filters split audio into frequency bands; 10MHz GBW ensures flat response to 100kHz+
  • Line Driver: 38mA output drives 600Ω balanced line; two amplifiers per channel for differential output
  • Headphone Amp: ±15V supply, 32Ω load; NE5532 delivers ~400mW per channel with 0.002% THD
Alternative Models: What chips are recommended as replacements for NE5532P
Model Manufacturer Key Difference Package Specs
NE5532AP TI Improved A-grade version with tighter offset voltage and noise specifications for premium audio DIP-8 10MHz/9V/µs
LM4562NA TI Ultra-low noise 2.7nV/rtHz audio op-amp with 55MHz GBW for high-end audio applications DIP-8 55MHz/20V/µs
OPA2134PA TI JFET-input audio op-amp with 8MHz GBW and ultra-low distortion for phono preamps DIP-8 8MHz/JFET
LM833N TI Dual audio op-amp with 15MHz GBW and low 5nV/rtHz noise for professional audio mixing DIP-8 15MHz/7V/µs
TL072CP TI Dual JFET-input op-amp with 3MHz GBW for general-purpose audio and filter circuits DIP-8 3MHz/JFET
OPA2604AP TI Dual FET-input audio op-amp with 20MHz GBW for professional and audiophile applications DIP-8 20MHz/FET

NE5532 is the industry-standard dual low-noise audio op-amp with 10MHz GBW, 9V/µs slew rate, and 5nV/rtHz input noise. It is the de facto choice for audio mixing consoles, preamps, and equalizers. For higher performance, the LM4562 offers 55MHz GBW and 2.7nV/rtHz noise. For JFET-input applications, OPA2134 provides ultra-low distortion in phono and microphone preamps.

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1