Opens in a new tab

LM317T

1.5A adjustable LDO, 1.25-37V, 0.1% regulation, TO-220

25000

Effective Inventory

Image for reference only

Manufacturer Part:

LM317T

Package:

TO-220-3 (15.6 x 10.6 x 4.6mm, through-hole, tab=VOUT)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM317T from onsemi/TI is a 1.5A adjustable positive voltage regulator with output range of 1.25V to 37V, 0.1% line regulation, and 0.1% load regulation in a TO-220 package—the most versatile linear regulator for adjustable power supplies.

Key Specifications

Output Voltage Range 1.25V to 37V (adjustable)
Output Current 1.5A max (with heatsink)
Input Voltage Range 4.25V to 40V (VOUT + 3V min)
Dropout Voltage 3V typical @ 1.5A
Reference Voltage (VREF) 1.25V typical (1.20V to 1.30V)
Line Regulation 0.01%/V typical (0.05% max)
Load Regulation 0.1% typical (0.5% max)
Adjust Pin Current 50µA typical, 100µA max
Adjust Pin Current Change 0.2µA typical, 5µA max
Ripple Rejection 65dB typical @ 120Hz
Output Noise 0.003%/V of output
Thermal Shutdown ~170°C junction
Current Limit ~2.2A typical (internally limited)
Operating Temperature 0°C to +125°C (junction)
Package TO-220-3 (through-hole, tab=VOUT)

Features

  • Adjustable output from 1.25V to 37V
  • 1.5A output current
  • Excellent line and load regulation: 0.01%/V, 0.1%
  • Internal thermal overload protection
  • Internal short-circuit current limiting
  • Output transistor safe operating area protection
  • Floating operation (can regulate negative voltages)
  • Only two external resistors set output voltage

Applications

  • Adjustable bench power supply
  • Battery charger circuits
  • Current regulator (constant current source)
  • Adjustable voltage reference
  • Lab and test equipment power
Product Introduction: LM317T Product Introduction

The LM317T from onsemi/Texas Instruments is the industry-standard adjustable positive voltage regulator, capable of supplying 1.5A over an output range of 1.25V to 37V. The output voltage is set by just two external resistors: VOUT = 1.25V × (1 + R2/R1) + IADJ × R2, where IADJ is typically 50µA. The 1.25V reference between the output and adjust pins is exceptionally stable, providing 0.01%/V line regulation and 0.1% load regulation—far better than fixed 78xx regulators. The device is fully floating: it has no ground connection, allowing it to regulate negative voltages when the output is tied to ground. The adjust pin can be bypassed with a capacitor for improved ripple rejection (up to 80dB). The internal protection includes thermal shutdown, current limiting, and safe operating area compensation. The T suffix denotes the TO-220 through-hole package. The LM317 is also commonly used as a constant-current source: connecting the load between the output and adjust pins, with a single resistor from adjust to ground, sets the current to I = 1.25V/R.

Working Principle: LM317T Working Principle

The LM317T maintains a constant 1.25V reference between its output (OUT) and adjust (ADJ) pins. This means that when a resistor R1 is connected between OUT and ADJ, a constant current of I = 1.25V/R1 flows through R1. This same current (plus the small 50µA adjust pin current) flows through a second resistor R2 connected from ADJ to ground. The output voltage is VOUT = 1.25V + (1.25V/R1 + IADJ) × R2 = 1.25V × (1 + R2/R1) + IADJ × R2. With R1 = 240Ω (standard value), the current through R1 is approximately 5.2mA, which is well above the 3.5mA minimum load current required for regulation. The adjust pin current (50µA) adds a small error: with R2 = 4.8kΩ, IADJ × R2 = 0.24V, giving VOUT ≈ 1.25 × (1 + 4800/240) + 0.24 = 26.24V. For a constant-current source, the load is connected between OUT and ADJ (in place of R1), and a single resistor R from ADJ to ground sets the current: I = 1.25V/R. For 100mA, R = 1.25V/0.1A = 12.5Ω. The 10µF capacitor on the adjust pin (to ground) improves ripple rejection by bypassing AC signals on the adjust pin, preventing them from modulating the output voltage. The LM317 is a floating regulator: its internal circuitry operates between the input and output pins, with the reference from output to adjust. Since there is no ground connection, the regulator can be used in negative supply configurations by connecting the output to ground and taking the negative output from the input terminal.

Pin Description: LM317T Pin Definition and Functions
Pin Name Type Description
1 ADJ Adjustment Adjustment pin sets output voltage via external resistor divider. Voltage at this pin is maintained at 1.25V below VOUT by the internal reference. Connect R1 between VOUT and ADJ (typically 240Ω), and R2 between ADJ and GND. Output voltage = 1.25V × (1 + R2/R1) + Iadj × R2, where Iadj ≈ 50µA.
2 VOUT Power Output Regulated output voltage from 1.25V to 37V at up to 1.5A. The tab of TO-220 package is electrically connected to VOUT. Bypass with 1µF solid tantalum or 10µF electrolytic capacitor to GND. Add protection diode from ADJ to VOUT if output capacitors exceed 10µF.
3 VIN Power Input Unregulated input voltage. Must be at least Vout + Vdropout (3V typ at 1.5A) for proper regulation. Maximum 40V. Bypass with 0.1µF ceramic or 1µF tantalum capacitor to GND when supply is remote. Input voltage must not go negative below -0.7V.

LM317T pin assignment (TO-220-3, front view, pins down): Pin 1 (left) = ADJ, Pin 2 (center) = VOUT/Tab, Pin 3 (right) = VIN. Note the ADJ pin is on the left, unlike fixed 78xx regulators where Input is on the left. The tab is connected to VOUT, not GND. For safe operation with large output capacitors or reverse voltage conditions, add protection diodes: D1 from ADJ to VOUT (1N4001) and D2 from VOUT to VIN (1N5400).

Application Scenarios: In which products and applications is LM317T used
  • Variable PSU: 24V input, R1=240Ω, R2=5kΩ pot; VOUT = 1.25-27.5V adjustable; 10µF cap on ADJ for 80dB ripple rejection
  • Constant Current: Load between OUT and ADJ; R=12.5Ω from ADJ to GND; I=100mA constant current for LED or battery charging
  • Battery Charger: LM317 in CC/CV mode; current limit set by R=1.25V/0.1A=12.5Ω; voltage limit set by R2
  • 1.25V Reference: ADJ tied to GND; VOUT = 1.25V; 0.1% regulation; replaces zener diode
  • Negative Supply: OUT tied to GND; input from negative source; ADJ resistor to negative output; floating operation
Alternative Models: What chips are recommended as replacements for LM317T
Model Manufacturer Key Difference Package Specs
LM317AT onsemi Tighter reference voltage tolerance ±1% vs ±4% for precision adjustable power supplies TO-220-3 1.25-37V/1.5A
LM317EMP/NOPB TI SOT-223 surface-mount version for compact board designs with 1A output current SOT-223-4 1.25-37V/1A
LM317DCYT/NOPB TI SOT-223-3 with TO-263 compatibility and lower dropout for space-constrained designs SOT-223-3 1.25-37V/1A
LM337T TI Negative adjustable complement: -1.25V to -37V for symmetric split-rail power supplies TO-220-3 -1.25 to -37V/1.5A
LM1117MP-3.3 TI Lower dropout (1.1V) fixed 3.3V alternative for regulated 3.3V logic supply rails SOT-223-4 3.3V/800mA LDO
LM1085IT-5.0 TI 3A higher-current adjustable LDO for applications requiring more than 1.5A output TO-220-3 1.25-37V/3A

LM317T is a 1.25-37V adjustable positive voltage regulator in TO-220-3 with 1.5A output and ±4% reference tolerance. The LM317AT offers ±1% precision. For surface-mount, use LM317EMP (SOT-223). For higher current, LM1085 provides 3A output. The LM337T is the negative complement for split-rail supplies. All require only two external resistors to set output voltage.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1