Opens in a new tab

LM358N

Dual op-amp, single-supply 3-32V, GND input, 1.2MHz GBW, PDIP-8

25000

Effective Inventory

Image for reference only

Manufacturer Part:

LM358N

Package:

PDIP-8 (9.81 x 6.35 x 5.08mm, 2.54mm pitch, through-hole)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM358N from Texas Instruments is a dual general-purpose operational amplifier with single-supply operation (3V to 32V), input common-mode range including ground, and 1.2MHz gain-bandwidth product in an 8-pin PDIP package.

Key Specifications

Number of Amplifiers 2 (dual, independent)
Supply Voltage 3V to 32V (single) or ±1.5V to ±16V (dual)
Gain-Bandwidth Product 1.2MHz typical
Slew Rate 0.5V/µs typical
Input Offset Voltage 2mV typical, 7mV max
Input Bias Current 45nA typical
Input Common-Mode Range 0V to V+−1.5V (includes ground)
Output Voltage Swing 0V to V+−1.5V (single supply)
Output Current (source) 20mA typical
Output Current (sink) 10mA typical
Quiescent Current (both) 0.7mA typical
Large Signal Voltage Gain 100V/mV (100,000) typical
Operating Temperature 0°C to +70°C
Package PDIP-8 (9.81 x 6.35mm)

Features

  • Two independent op-amps in 8-pin DIP
  • Single-supply operation from 3V to 32V
  • Input common-mode range includes ground
  • Low supply current: 0.7mA for both
  • Output swings to ground (no negative supply needed)
  • No crossover distortion

Applications

  • Signal conditioning and filtering
  • Buffer/amplifier for sensors
  • Active filters
  • Voltage followers
  • Comparators (open-loop)
Product Introduction: LM358N Product Introduction

The LM358N from Texas Instruments is the industry-standard dual general-purpose operational amplifier optimized for single-supply operation. Its key advantage is the input common-mode voltage range that includes ground (0V), allowing it to amplify signals that go all the way down to the negative rail without requiring a dual supply. The output also swings close to ground (typically to 5mV with a 10kΩ load), eliminating the need for a negative supply in many applications. The 3V minimum supply voltage makes it compatible with 3.3V logic systems, while the 32V maximum allows use in automotive and industrial applications. The 1.2MHz gain-bandwidth product and 0.5V/µs slew rate are sufficient for DC and low-frequency AC applications (audio up to ~100kHz at unity gain). The N suffix denotes the commercial temperature range (0°C to +70°C) in PDIP-8. The LM358 is one of the most produced and lowest-cost op-amps in the world, available from TI, onsemi, STMicroelectronics, and dozens of other manufacturers.

Working Principle: LM358N Working Principle

The LM358N contains two independent operational amplifiers on one chip. Each op-amp is a high-gain differential amplifier with inverting (−) and non-inverting (+) inputs and a single output. In open-loop (no feedback), the gain is approximately 100,000 (100V/mV), so even a tiny voltage difference between the inputs drives the output to saturation. In closed-loop (with feedback), the gain is determined by the external resistor network: for an inverting amplifier, AV = −Rf/Rin; for a non-inverting amplifier, AV = 1 + Rf/Rin. The input stage uses PNP transistors that allow the common-mode input to go below ground by approximately 0.3V, and the internal biasing allows single-supply operation. The output stage is a Class-AB push-pull that can both source (up to 20mA) and sink (up to 10mA) current. When the output needs to go to 0V (ground), the sink capability pulls it close to ground, though not exactly to 0V under load. For a voltage follower (unity gain buffer), connect the output directly to the inverting input; the output then follows the non-inverting input exactly, with high input impedance and low output impedance.

Pin Description: LM358N Pin Definition and Functions
Pin Name Type Description
1 1OUT Output Op-amp 1 output
2 1IN− Input Op-amp 1 inverting input
3 1IN+ Input Op-amp 1 non-inverting input
4 GND Power Ground (or V− for dual supply)
5 2IN+ Input Op-amp 2 non-inverting input
6 2IN− Input Op-amp 2 inverting input
7 2OUT Output Op-amp 2 output
8 VCC Power Supply (3V to 32V)

LM358N uses the PDIP-8 (N) package with industry-standard dual op-amp pinout: Pin 1 = Output A, Pin 2 = Inverting Input A (-), Pin 3 = Non-inverting Input A (+), Pin 4 = GND/VEE, Pin 5 = Non-inverting Input B (+), Pin 6 = Inverting Input B (-), Pin 7 = Output B, Pin 8 = VCC. This pinout is shared by all dual op-amps in DIP-8 including LM358, LM2904, RC4558, NE5532, and TL072. The single-supply operation (3V-32V or ±1.5V to ±16V) allows inputs to go to ground without phase reversal. Output swings to within 0-20mV of ground in single-supply configuration. For surface-mount, LM358DR (SOIC-8) provides identical pinout.

Application Scenarios: In which products and applications is LM358N used
  • Inverting Amp: Input through Rin to IN−; Rf from IN− to OUT; IN+ to GND; gain = −Rf/Rin; inverts and amplifies
  • Non-Inverting Amp: Input to IN+; Rf from OUT to IN−; Rin from IN− to GND; gain = 1 + Rf/Rin; amplifies without inversion
  • Voltage Follower: OUT connected directly to IN−; input at IN+; gain = 1; high-Z input, low-Z output buffer
  • Schmitt Trigger: Positive feedback from output to IN+ through resistor divider; creates hysteresis; cleans noisy digital signals
  • Difference Amp: Both inputs used; output = gain × (IN+ − IN−); measures voltage across a shunt resistor
Alternative Models: What chips are recommended as replacements for LM358N
Model Manufacturer Key Difference Package Specs
LM358AN TI Improved version with lower input offset voltage 2mV max vs 7mV for precision signal conditioning DIP-8 1.1MHz/0.6V/µs
LM358B TI Modern upgrade: 36V supply, 1.2MHz GBW, 3mV offset, and rail-to-rail output swing DIP-8 1.2MHz/36V
LM324N TI Quad op-amp version (4 channels) in DIP-14 for multi-stage signal chain applications DIP-14 1.1MHz/4-ch
LM2904N TI Automotive-grade -40 to +125C version with enhanced ESD protection for harsh environments DIP-8 1.1MHz/-40-125C
LMV358IDR TI Low-voltage 2.7-5.5V version with 1MHz GBW for 3.3V and battery-powered systems SOIC-8 1MHz/2.7-5.5V
NE5532P TI Dual low-noise audio op-amp with 10MHz GBW for audio preamp and filter applications DIP-8 10MHz/9V/µs

LM358 is the industry-standard dual general-purpose op-amp with 1.1MHz GBW and 3-32V single-supply operation. Input common-mode range includes ground for single-supply sensor interfacing. LM358B offers modern 36V rail-to-rail output. For quad needs, LM324 provides 4 channels. For audio, NE5532 offers 10MHz GBW and low noise. LM2904 extends temperature range to 125C for automotive applications.

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1