Opens in a new tab

2N2222A

NPN BJT, 40V 600mA, hFE 100-300, TO-92, general-purpose

25596

Effective Inventory

Image for reference only

Manufacturer Part:

2N2222A

Package:

TO-92-3 (4.83 x 4.76 x 4.19mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The 2N2222A is the classic general-purpose NPN bipolar junction transistor with 40V collector-emitter voltage, 600mA collector current, and 300MHz transition frequency in a TO-92 package — one of the most recognized and widely used transistors in electronics.

Key Specifications

Type NPN Bipolar Junction Transistor (BJT)
Collector-Emitter Voltage (VCEO) 40V
Collector-Base Voltage (VCBO) 75V
Emitter-Base Voltage (VEBO) 6V
Collector Current (IC) 600mA continuous
DC Current Gain (hFE) 100-300 @ IC=150mA, VCE=10V
Collector-Emitter Saturation (VCE(sat)) 0.3V max @ IC=150mA, IB=15mA; 1.0V @ IC=500mA, IB=50mA
Base-Emitter Saturation (VBE(sat)) 2.0V max @ IC=500mA, IB=50mA
Transition Frequency (fT) 250-300MHz
Output Capacitance (Cob) 8pF typical
Power Dissipation 625mW @ TA=25°C
Operating Temperature -65°C to +150°C
Package TO-92-3 (4.83 x 4.76mm)

Features

  • General-purpose NPN transistor
  • 600mA collector current — higher than BC547 (100mA)
  • 40V VCEO — suitable for 5V-24V systems
  • 300MHz fT — suitable for RF up to ~30MHz
  • Complementary PNP: 2N2907A

Applications

  • Low-power switching (relay, LED, motor)
  • Signal amplification
  • Logic-level interfacing
  • Audio preamplifier
  • Simple oscillator circuits
Product Introduction: 2N2222A Product Introduction

The 2N2222A is one of the oldest and most ubiquitous NPN transistors, originally introduced by Motorola in the 1960s and now available from onsemi, Diotec, STMicroelectronics, and dozens of other manufacturers. The ‘A’ suffix version has a 40V VCEO rating (vs. 30V for the non-A 2N2222), making it suitable for 24V systems. With 600mA collector current, it sits between small-signal transistors like the BC547 (100mA) and power transistors like the TIP122 (5A). The 625mW power dissipation in TO-92 limits it to low-power applications without a heatsink. The 100-300 hFE range at 150mA provides substantial current gain, allowing a 5mA base current from a microcontroller GPIO to switch up to 500mA loads (with some saturation voltage). The 300MHz transition frequency makes it usable for RF applications up to approximately 30MHz (fT/10 as a practical rule). The complementary PNP transistor is the 2N2907A. Pin 1 is Emitter, Pin 2 is Base, Pin 3 is Collector (TO-92, flat face toward you, pins down).

Working Principle: 2N2222A Working Principle

The 2N2222A is an NPN bipolar junction transistor. Current flows from collector to emitter (conventional current direction) when base current is applied. The relationship IC = hFE × IB defines the current gain; at IC=150mA, hFE is typically 150-250, meaning IB=0.6-1.5mA produces IC=150mA. For switching applications, the transistor must be driven into saturation: IB must exceed IC/hFE by a factor of 2-10 (overdrive factor) to ensure VCE drops to VCE(sat) ≈ 0.3V. For a 150mA load, IB should be at least 3mA (IC/hFE = 1.5mA × 2 overdrive). For a 500mA load, VCE(sat) rises to 1.0V because hFE drops at high current; IB must be 50mA (10% of IC) for the datasheet-specified saturation voltage. The base-emitter junction is a forward-biased diode with VBE ≈ 0.7V; the base resistor value is RB = (Vdrive − VBE) / IB. For a 5V MCU driving a 150mA load: IB = 3mA, RB = (5V − 0.7V) / 3mA ≈ 1.5kΩ. The collector current cannot exceed 600mA continuously, and total power dissipation must stay below 625mW: P = VCE × IC + VBE × IB. At saturation: P ≈ 0.3V × 150mA = 45mW, well within limits.

Pin Description: 2N2222A Pin Definition and Functions
Pin Name Type Description
1 Emitter Output Emitter terminal. Connects to ground in common-emitter configuration for NPN operation. The emitter is the most negative terminal during forward active operation. Maximum continuous emitter current is 800mA. Reverse breakdown VEB0 = 6V minimum.
2 Base Input Base terminal controls the collector current. Apply forward bias VBE ≈ 0.7V to turn ON. DC current gain hFE ranges from 35 to 300 across grades (A suffix = tighter specs). Drive IB > IC/hFE(min) for saturation switching. Maximum base current 200mA (pulsed).
3 Collector Power Output Collector terminal connects to the load. Rated for 40V VCEO (75V VCBO) and 600mA continuous collector current. Power dissipation 625mW at TA=25°C. VCE(sat) = 0.3V max at IC=150mA, IB=15mA for efficient switching applications. Transition frequency fT = 300MHz.

2N2222A pin assignment (TO-92-3, flat face toward you, pins down): Pin 1 (left) = Emitter, Pin 2 (center) = Base, Pin 3 (right) = Collector. The A suffix version has tighter hFE grouping and higher 40V VCEO vs 30V for 2N2222. Complementary PNP: 2N2907A (-60V/-600mA). Metal-can TO-18 version: 2N2222A (same die in TO-18 with Pin 1=E, Pin 2=B, Pin 3=C from bottom view). SMD equivalent: MMBT2222A (SOT-23) for surface-mount designs.

Application Scenarios: In which products and applications is 2N2222A used
  • MCU Relay Driver: MCU GPIO → 1kΩ base resistor → 2N2222A base; collector to relay coil; emitter to GND; flyback diode across coil; IC=~100mA
  • LED Switch: MCU → 2.2kΩ → base; collector to LED+resistor; emitter GND; switches up to 200mA LED strings
  • Logic Inverter: Input → base resistor; output at collector with pull-up; inverts signal with current gain
  • Emitter Follower: Input → base; output at emitter; voltage gain ≈ 1; current gain = hFE; low output impedance buffer
  • Small Motor Drive: PWM → base resistor; collector to 12V motor; emitter GND; up to ~400mA with heatsink on tab
Alternative Models: What chips are recommended as replacements for 2N2222A
Model Manufacturer Key Difference Package Specs
PN2222A onsemi Same die, different pinout (EBC vs CBE), TO-92 – –
BC547B Various Lower current (100mA), lower noise, TO-92 – –
2N3904 Various 200mA, 40V, lower current but widely available – –
S8050 onsemi 1.5A, 25V, higher current but lower voltage, TO-92 – –
MMBT2222A Various SMD version in SOT-23 package – –

2N2222A is a 40V/600mA NPN general-purpose transistor in TO-92. The PN2222A provides the same specs with different pinout (EBC vs CBE for metal can). The MMBT2222A is the SOT-23 surface-mount equivalent. The BC547B offers higher gain (200-450 hFE) at lower 45V/100mA. The 2N3904 provides 40V/200mA at lower cost for small-signal applications. The MPS2222A from onsemi is the SOT-23 equivalent. The 2N4401 provides 40V/600mA with higher gain in TO-92. For higher power, TIP122G Darlington offers 100V/5A with 1000x hFE.

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1