Opens in a new tab

LM7812CT

12V 1A positive linear regulator, TO-220, thermal/SCP protection

25000

Effective Inventory

Image for reference only

Manufacturer Part:

LM7812CT

Package:

TO-220-3 (10.16 x 4.7 x 20.4mm, through-hole, tab=GND)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM7812CT from onsemi is a 3-terminal 1A positive voltage regulator providing a fixed 12V output with 71dB ripple rejection and internal protection in a TO-220 package — the standard 12V regulator for industrial and automotive electronics.

Key Specifications

Output Voltage 12V fixed (±4% at 25°C)
Output Current 1A continuous
Input Voltage Range 14.5V to 35V
Dropout Voltage 2V typical @ 1A
Line Regulation 10mV typical (14.5V to 27V)
Load Regulation 12mV typical (5mA to 1.5A)
Quiescent Current 5.1mA typical
Ripple Rejection 71dB typical @ 120Hz
Output Noise 76µV/VO (10Hz to 100kHz)
Short-Circuit Current 250mA typical
Operating Temperature -40°C to +125°C (junction)
Package TO-220-3 (through-hole, tab=GND)

Features

  • Fixed 12V output — the most common industrial supply voltage
  • 1A continuous output current
  • Internal thermal overload protection
  • Internal short-circuit current limiting
  • 71dB ripple rejection
  • Output transistor SOA protection

Applications

  • 12V industrial power supply
  • Automotive 12V rail
  • Relay and solenoid power
  • Op-amp ±12V supply
  • Instrumentation power
Product Introduction: LM7812CT Product Introduction

The LM7812CT from onsemi is the 12V member of the LM78XX family — arguably the most important voltage in the series because 12V is the dominant supply rail in industrial, automotive, and communications equipment. From 12V, 5V can be derived with a secondary regulator (LM7805), and ±12V supplies are used for analog op-amp circuits. The minimum input voltage for regulation is 14.5V (12V + 2.5V dropout margin), making it ideal for automotive applications where the 14.4V alternator output directly feeds the regulator. The 71dB ripple rejection attenuates alternator whine and rectified AC ripple. The CT suffix denotes the TO-220 package. Power dissipation can be significant: at VIN=24V and IOUT=500mA, Pd = (24-12)×0.5 = 6W, requiring a heatsink.

Working Principle: LM7812CT Working Principle

The LM7812CT uses a series pass transistor (NPN Darlington) between input and output, controlled by a feedback loop that compares a fraction of the output voltage with an internal bandgap reference. When the output drops below 12V, the error amplifier increases drive to the pass transistor, increasing current flow. When the output rises above 12V, drive is reduced. The thermal protection disables the output at ~170°C junction temperature. The current limiting restricts output during a short circuit to ~250mA. The safe operating area (SOA) protection further reduces current limit as the input-output differential increases. The 5.1mA quiescent current flows through the ground pin and biases the internal reference and error amplifier. Power dissipation is Pd = (VIN − 12V) × IOUT; at VIN=18V, IOUT=1A: Pd = 6W. The heatsink thermal resistance must satisfy: θSA < (TJ_max − TA)/Pd − θJC − θCS. For TJ=100°C, TA=50°C: θSA < 50/6 − 5 − 0.5 = 2.83°C/W — a substantial heatsink.

Pin Description: LM7812CT Pin Definition and Functions
Pin Name Type Description
1 INPUT Power Input Unregulated input voltage. Must be at least 3.7V (Vout + Vdropout ≈ 3.7V) for proper regulation. Maximum 35V. Bypass with 0.33µF ceramic capacitor to GND if supply is more than 6 inches from the regulator.
2 GND Ground Common ground reference. The TO-220 tab is electrically connected to this pin and serves as the primary heat dissipation path. Use thermal compound and heatsink for currents above 500mA.
3 OUTPUT Power Output Regulated 1.2V DC output at up to 1A continuous current with ±4% tolerance. Bypass with 0.1µF ceramic capacitor to GND to improve transient response and output impedance. Do not apply external voltage higher than 1.2V to prevent reverse bias damage.

Pin assignment follows standard TO-220-3 layout: Pin 1 (left) = Input, Pin 2 (center) = Ground/Tab, Pin 3 (right) = Output, when viewed from the front with pins pointing down. The metal tab on the back is electrically connected to Pin 2 (GND) and must be insulated from the heatsink when the heatsink is not at ground potential. Output capacitance of 0.1µF is required for stability; input capacitance of 0.33µF is recommended when the input supply is remote.

Application Scenarios: In which products and applications is LM7812CT used
  • 12V Industrial Supply: 18V DC (from transformer+rectifier+filter) → LM7812CT → 12V rail; 0.33µF input + 0.1µF output caps
  • Dual 12V/5V: 18V → LM7812CT → 12V rail; 12V → LM7805CT → 5V rail; cascaded regulation
  • ±12V Op-Amp Supply: LM7812CT (+12V) + LM7912CT (-12V) from center-tapped transformer; clean ±12V for NE5532
  • Automotive 12V: Car 14.4V → LM7812CT → stable 12V; 71dB rejection of alternator noise
Alternative Models: What chips are recommended as replacements for LM7812CT
Model Manufacturer Key Difference Package Specs
LM7812ACT onsemi Tighter output tolerance: ±2% vs ±4% for precision power supply applications TO-220-3 1.2V/1A
L7812CV STMicroelectronics Direct equivalent with 1.5A output current, internal thermal shutdown and current limiting TO-220-3 1.2V/1.5A
MC7812CTG onsemi Current production replacement with identical electrical specifications and RoHS compliance TO-220-3 1.2V/1A
KA7812 onsemi/Fairchild Budget-friendly version with ±4% tolerance and standard 1A output current rating TO-220-3 1.2V/1A
MC7812ABD2TG onsemi Surface-mount DPAK version with ±2% A-grade tolerance for compact PCB layouts DPAK-3 1.2V/1A
LM2940CT-1.2 TI Low-dropout version with 0.5V max dropout at 1A for battery-powered and automotive systems TO-220-3 1.2V/1A LDO

LM7812CT is a 1.2V fixed positive voltage regulator in TO-220-3 with 1A output and ±4% tolerance. The ACT suffix offers ±2% precision. For surface-mount designs, use MC7812ABD2TG (DPAK). For battery-powered systems, the LM2940CT-1.2 LDO version reduces dropout to 0.5V. All 7812 variants are pin-compatible (IN-GND-OUT) and require only input/output capacitors.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1