Opens in a new tab

LM358N

Dual general-purpose op-amp, 1MHz, 3-32V single supply, GND-referenced, PDIP-8

20000

Effective Inventory

Image for reference only

Manufacturer Part:

LM358N

Package:

PDIP-8 (9.81 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM358N from Texas Instruments is the dual version of the LM324 — two general-purpose op-amps with single-supply operation (3V-32V), ground-referenced inputs, and 1MHz bandwidth in an 8-pin PDIP package.

Key Specifications

Number of Channels 2 (dual, independent)
Supply Voltage Range 3V to 32V (single) or ±1.5V to ±16V (dual)
Gain-Bandwidth Product 1MHz typical
Slew Rate 0.5V/µs typical
Open-Loop Voltage Gain 100dB typical
Input Offset Voltage 2mV typical, 7mV max
Input Bias Current 45nA typical
Input Common-Mode Range 0V to V+−1.5V (includes GND)
Output Voltage Swing 0V to V+−1.5V
Supply Current (both amps) 350µA typical
Operating Temperature 0°C to +70°C
Package PDIP-8 (9.81 x 6.35mm)

Features

  • Two internally compensated op-amps in one 8-pin package
  • Single-supply operation: 3V to 32V
  • Input common-mode range includes ground
  • Output swings to ground (no negative supply needed)
  • 350µA total supply current

Applications

  • Single-supply signal conditioning
  • Sensor amplifier interfaces
  • DC gain blocks
  • Comparators
  • Active filters
Product Introduction: LM358N Product Introduction

The LM358N from Texas Instruments is the dual version of the LM324, containing two independent general-purpose op-amps in a compact 8-pin DIP package. It shares all the LM324’s key advantages: single-supply operation from 3V to 32V, input common-mode range including ground, output swinging to near ground, and low 350µA total supply current. The 8-pin DIP footprint is smaller than the LM324’s 14-pin, making the LM358 ideal when only one or two op-amp channels are needed. The pinout follows the industry-standard dual-op-amp convention (same as NE5532, TL072, LM833), allowing easy upgrades to higher-performance op-amps. The 1MHz GBW and 0.5V/µs slew rate are adequate for DC signal conditioning, audio preamplification, and low-frequency active filtering. At $0.20/1ku, the LM358 is one of the most cost-effective op-amps available. The N suffix denotes the PDIP-8 through-hole package.

Working Principle: LM358N Working Principle

The LM358N operates identically to half of the LM324. Each op-amp uses a PNP differential input stage that allows the common-mode range to include ground. The class AB output stage can source current (pulling output toward V+) and sink current (pulling output toward ground), with the output able to swing to within ~5mV of ground when sinking small currents. In single-supply operation, the signal must remain between 0V and V+−1.5V at both input and output. The internal compensation capacitor ensures stability in voltage-follower (unity gain) configuration without external components. Closed-loop bandwidth = GBW / noise_gain; at gain=10, BW ≈ 100kHz. The 0.5V/µs slew rate limits the full-power bandwidth: at 5V peak output, BW_max = 0.5/(2π×5) ≈ 16kHz. For AC-coupled applications, a V+/2 bias voltage is needed; for DC ground-referenced signals (sensors, battery monitors), no bias is required.

Pin Description: LM358N Pin Definition and Functions
Pin Name Type Description
1 1OUT Output Op-amp 1 output
2 1IN− Input Op-amp 1 inverting input
3 1IN+ Input Op-amp 1 non-inverting input
4 GND / V− Power Ground or negative supply
5 2IN+ Input Op-amp 2 non-inverting input
6 2IN− Input Op-amp 2 inverting input
7 2OUT Output Op-amp 2 output
8 VCC Power Positive supply (3V to 32V)

LM358N uses the PDIP-8 (N) package with industry-standard dual op-amp pinout: Pin 1 = Output A, Pin 2 = Inverting Input A (-), Pin 3 = Non-inverting Input A (+), Pin 4 = GND/VEE, Pin 5 = Non-inverting Input B (+), Pin 6 = Inverting Input B (-), Pin 7 = Output B, Pin 8 = VCC. This pinout is shared by all dual op-amps in DIP-8 including LM358, LM2904, RC4558, NE5532, and TL072. The single-supply operation (3V-32V or ±1.5V to ±16V) allows inputs to go to ground without phase reversal. Output swings to within 0-20mV of ground in single-supply configuration. For surface-mount, LM358DR (SOIC-8) provides identical pinout.

Application Scenarios: In which products and applications is LM358N used
  • Non-Inverting Amp: Sensor (0-0.5V) → 1IN+; Rf=90kΩ, Rg=10kΩ; Gain=10; 1OUT = 0-5V; VCC=5V single supply
  • Comparator: Voltage sense → 1IN+; reference → 1IN−; no feedback; 1OUT drives relay driver or LED
  • Differential Amp: Bridge sensor → 1IN+ and 1IN−; Rf/Rg set gain; 1OUT = amplified difference
  • AC-Coupled Preamp: VCC=9V; two 100kΩ divider → V+/2 = 4.5V at 1IN+; AC signal through cap → Rin → 1IN−; Rf feedback
Alternative Models: What chips are recommended as replacements for LM358N
Model Manufacturer Key Difference Package Specs
LM358AN TI Improved version with lower input offset voltage 2mV max vs 7mV for precision signal conditioning DIP-8 1.1MHz/0.6V/µs
LM358B TI Modern upgrade: 36V supply, 1.2MHz GBW, 3mV offset, and rail-to-rail output swing DIP-8 1.2MHz/36V
LM324N TI Quad op-amp version (4 channels) in DIP-14 for multi-stage signal chain applications DIP-14 1.1MHz/4-ch
LM2904N TI Automotive-grade -40 to +125C version with enhanced ESD protection for harsh environments DIP-8 1.1MHz/-40-125C
LMV358IDR TI Low-voltage 2.7-5.5V version with 1MHz GBW for 3.3V and battery-powered systems SOIC-8 1MHz/2.7-5.5V
NE5532P TI Dual low-noise audio op-amp with 10MHz GBW for audio preamp and filter applications DIP-8 10MHz/9V/µs

LM358 is the industry-standard dual general-purpose op-amp with 1.1MHz GBW and 3-32V single-supply operation. Input common-mode range includes ground for single-supply sensor interfacing. LM358B offers modern 36V rail-to-rail output. For quad needs, LM324 provides 4 channels. For audio, NE5532 offers 10MHz GBW and low noise. LM2904 extends temperature range to 125C for automotive applications.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1