Opens in a new tab

CD4076BE

4-bit D register, 3-state outputs, input/output disable, CMOS 3-18V, PDIP-16

2000

Effective Inventory

Image for reference only

Manufacturer Part:

CD4076BE

Package:

PDIP-16 (19.3 x 9.4 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The CD4076BE from Texas Instruments is a 4-bit D-type register with 3-state outputs and input/output disable controls — a registered bus transceiver for multi-master bus systems in a 16-pin PDIP package.

Key Specifications

Function 4-bit D-type register with 3-state outputs
Technology CD4000B CMOS
Supply Voltage 3V to 18V
Register Bits 4
Clock Positive edge triggered
Data Disable DI1, DI2 (both LOW = data enabled; any HIGH = input forced LOW)
Output Disable DO1, DO2 (both LOW = outputs enabled; any HIGH = high-Z)
Clear Asynchronous, active-HIGH (RST)
Propagation Delay 200ns typical @ VDD=10V
Operating Temperature -55°C to +125°C
Package PDIP-16 (19.3 x 9.4mm)

Features

  • 4-bit edge-triggered D register
  • 3-state outputs for bus connection
  • Independent input and output disable controls
  • Asynchronous clear
  • 3V-18V wide supply range

Applications

  • Bus registers
  • I/O port latches
  • Data buffering with bus isolation
  • Multi-master bus systems
Product Introduction: CD4076BE Product Introduction

The CD4076BE from Texas Instruments is a 4-bit edge-triggered D register with 3-state outputs and separate input/output disable controls. It captures 4 bits of data on the rising clock edge and holds them until the next clock. The 3-state outputs allow multiple CD4076 registers to share a common bus — only one register drives the bus at a time. The input disable (DI1, DI2) controls what gets loaded: when both DI1 and DI2 are LOW, the D inputs pass through normally; when either DI1 or DI2 is HIGH, the inputs are forced LOW internally (zeros are loaded on the next clock). This allows one input to serve as a data enable while the other provides a zero-load function. The output disable (DO1, DO2) controls the 3-state outputs: when both are LOW, outputs drive the bus; when either is HIGH, outputs go to high-impedance. The two disable inputs each provide independent gating, allowing flexible control logic. The asynchronous clear (RST=HIGH) resets all flip-flops to 0. The BE suffix denotes the PDIP-16 package.

Working Principle: CD4076BE Working Principle

The CD4076BE captures data on the rising edge of CLK. On each rising CLK edge, the D0-D3 inputs (after input disable gating) are stored in the four D flip-flops. The stored data appears on Q0-Q3 when the output enables are active (both DO1 and DO2 LOW). Input disable: DI1 and DI2 are ANDed (both must be LOW for data to pass). If either DI1 or DI2 is HIGH, the internal data path is forced to 0 — zeros are loaded on the next clock instead of the D inputs. This is useful for selectively loading data or clearing the register via clock. Output disable: DO1 and DO2 are ANDed (both must be LOW for outputs to drive). If either DO1 or DO2 is HIGH, Q0-Q3 go to high-impedance (disconnected from the bus). Multiple CD4076 registers can share a bus; only one has its outputs enabled at a time (controlled by a decoder driving DO1 or DO2). Clear: RST=HIGH asynchronously resets all flip-flops to 0, regardless of CLK, D inputs, or disable controls.

Pin Description: CD4076BE Pin Definition and Functions
Pin Name Type Description
1 DO1 Input Output disable 1 (HIGH = outputs high-Z)
2 Q0 Output Register output bit 0 (3-state)
3 Q1 Output Register output bit 1 (3-state)
4 DO2 Input Output disable 2 (HIGH = outputs high-Z)
5 D0 Input Register data input bit 0
6 D1 Input Register data input bit 1
7 RST Input Asynchronous reset (active HIGH)
8 VSS Power Ground
9 CLK Input Clock (positive edge triggered)
10 DI1 Input Data input disable 1 (HIGH = force input LOW)
11 DI2 Input Data input disable 2 (HIGH = force input LOW)
12 D2 Input Register data input bit 2
13 D3 Input Register data input bit 3
14 Q2 Output Register output bit 2 (3-state)
15 Q3 Output Register output bit 3 (3-state)
16 VDD Power Supply (3V to 18V)
Application Scenarios: In which products and applications is CD4076BE used
  • Bus Register: 4-bit bus data → D0-D3; CLK captures data; DO1/DO2 from address decoder; only selected register drives bus
  • I/O Port: MCU writes data → D0-D3 with CLK; MCU reads → Q0-Q3 with DO enable; DI1 used as write enable; bidirectional I/O port
  • Multi-Port Register: Two CD4076s share output bus; one reads port A, other reads port B; address decoder selects which drives bus via DO
  • Zero-Load: DI1 = load enable (LOW=load data, HIGH=load zeros); DI2 = tied LOW; selectively load data or clear register via clock
Alternative Models: What chips are recommended as replacements for CD4076BE
Model Manufacturer Key Difference Package Supply
CD4076BM TI SOIC-16 surface-mount version with identical logic function and 3-18V range SOIC-16 3-18V
CD4076BE TI Through-hole DIP version for prototyping and legacy board repair DIP-16 3-18V
HEF4076BT NXP Pin-compatible CMOS version with improved ESD protection and 3-15V supply SOIC-16 3-15V
MC144076BDR2G onsemi Pin-compatible equivalent with RoHS compliance and AEC-Q100 automotive option SOIC-16 3-18V
74LS173D TI/Nexperia HC CMOS version with higher speed and 2-6V supply for modern logic systems SOIC-16 2-6V
74LS173N TI/Nexperia HC CMOS through-hole version for prototyping with 2-6V supply range DIP-16 2-6V
74LS173D Nexperia HCT version with TTL-compatible inputs for mixed 5V TTL/CMOS systems SOIC-16 4.5-5.5V

CD4076 is the CMOS 4000-series 4-bit register with 3-state operating over the wide 3-18V supply range. The HEF4076 (NXP) and MC144076 (onsemi) are direct pin-compatible equivalents. For higher speed at the cost of narrower voltage range, the 74LS173 HC/HCT families offer significantly faster propagation delay and lower power consumption at 2-6V. Surface-mount versions use the BM/M suffix (SOIC); through-hole versions use the BE suffix (DIP).

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1