Opens in a new tab

TB6600HG

Stepper motor driver, 4.5A, 50V, HZIP-25

2877

Effective Inventory

Image for reference only

Manufacturer Part:

TB6600HG

Package:

HZIP-25 (28.5 x 15.9 x 5.0 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

TB6600HG Overview

The TB6600HG is a PWM chopper-type bipolar stepping motor driver from Toshiba, with maximum operating voltage of 50V, output current of 4.5A, supporting 1/32 microstepping, in an HZIP-25 package, widely used in 3D printers and CNC controllers.

Key Features

  • Supply voltage: 8V-50V
  • Maximum output current: 4.5A
  • Microstep resolution: 1/32
  • Chopper frequency: 100kHz
  • Thermal shutdown protection
  • Overcurrent protection
Product Introduction: TB6600HG Product Introduction

The TB6600HG is a PWM chopper-type bipolar stepper motor driver IC from Toshiba in a HZIP-25 through-hole package, supporting motor voltages up to 50 V and output currents up to 5.0 A peak (4.5 A operating maximum). It features microstepping resolution of full step, 1/2, 1/4, 1/8, and 1/16 with built-in sinusoidal PWM current control. The device integrates MOSFET H-bridge outputs with 0.4 Ohm typical on-resistance (upper plus lower), over-current detection, thermal shutdown at 170 C, and under-voltage lockout. Step and direction interface enables simple microcontroller control with built-in 100 kOhm input pull-down resistors.

Working Principle: TB6600HG Working Principle

The TB6600HG controls bipolar stepper motor current using a fixed-off-time PWM chopper scheme. The H-bridge MOSFET outputs drive current through the motor winding in the forward or reverse direction based on the phase logic. Current flows through the winding, through the sense resistor to ground. When the voltage across the sense resistor exceeds the reference voltage set by the VREF input, the comparator triggers and the bridge enters the decay mode for the programmed off-time period. During slow decay, both low-side MOSFETs are turned on, allowing current to recirculate through the winding. During fast decay, the bridge reverses polarity, actively driving current back toward the supply. The TB6600HG uses a 40 percent fast decay mode where the final 40 percent of the off-time is fast decay and the remainder is slow decay, optimizing current regulation across the speed range. The microstepping logic divides each full step into up to 16 microsteps by modulating the current reference levels through an internal DAC, producing smooth sinusoidal winding currents. The CLK input advances the microstep sequencer on each rising edge, and the CW/CCW input sets the rotation direction. The M1, M2, and M3 inputs select the step resolution mode. The standby mode (M1=M2=M3=low or high) disables all outputs to minimize power consumption.

Pin Description: TB6600HG Pin Definition and Functions
Pin Name Description
1 OUT1A H-bridge A output 1; motor winding A connection
2 PGND1 Power ground for H-bridge A
3 OUT2A H-bridge A output 2; motor winding A connection
4 PGND2 Power ground for H-bridge B
5 OUT2B H-bridge B output 2; motor winding B connection
6 PGND3 Power ground
7 OUT1B H-bridge B output 1; motor winding B connection
8-9 VCC (x2) Motor power supply (8 V to 42 V); both pins must be connected
10 CLK Step clock input; rising edge advances one microstep
11 CW/CCW Direction input; high = CW, low = CCW
12 ENABLE Enable input; low = outputs active, high = outputs disabled (Hi-Z)
13 RESET Reset input; low = resets phase to initial position
14 M1 Microstep mode select bit 1
15 M2 Microstep mode select bit 2
16 M3 Microstep mode select bit 3
17 TQ Torque setting input; adjusts output current ratio
18 VREF Current reference voltage; sets peak winding current via external resistor divider
19 OSCM Chopping frequency setting; connect external resistor (51 kOhm = 40 kHz)
20 ALERT Over-current detection output; active low
21 MO Phase monitor output; indicates current step position
Application Scenarios: In which products and applications is TB6600HG used
  • CNC Machine Drives: 3-axis and 4-axis CNC router and mill stepper motor control with microstepping
  • 3D Printers: Precision filament extruder and XY gantry stepper motor driving
  • Robotics: Bipolar stepper motor actuation in articulated robot joints and linear stages
  • Textile Machinery: Multi-axis yarn feed and fabric patterning with smooth microstepping
  • Medical Dispensers: Precision syringe pump and valve stepper motor control
Alternative Models: What chips are recommended as replacements for TB6600HG
Model Manufacturer Imax Voltage Microstep Package
TB6600FTG Toshiba 4.5 A 50 V 1/32 HTSSOP-48
DRV8825 Texas Instruments 2.5 A 45 V 1/32 HTSSOP-28
A4988 Allegro 2.0 A 35 V 1/16 TSSOP-28
TMC5160 Trinamic 3.0 A 60 V 1/256 QFN-48
LV8729 onsemi 2.0 A 40 V 1/128 QFP-44

TB6600HG is a 4.5A/42V bipolar stepper motor driver from Toshiba in HZIP-25 with up to 1/16 microstepping. The TB6600FTG is the surface-mount HTSSOP version. TB67S109AFTG provides higher 3.5A with 1/128 microstepping in a smaller QFN package. For higher current, TB6600HG outputs 4.5A peak. The DRV8825 from TI offers 2.5A with 1/32 microstepping in HTSSOP-28 as a lower-cost alternative. A4988 from Allegro provides 2A with 1/16 microstepping for 3D printer applications.

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1