Opens in a new tab

LTC2852IMS

3.3V RS485/RS422 transceiver, 20Mbps, MSOP-8

14212

Effective Inventory

Image for reference only

Manufacturer Part:

LTC2852IMS

Package:

MSOP-8 (3.00 x 3.00 x 0.90 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

LTC2852IMS Overview

The LTC2852IMS is a 3.3V RS-485/RS-422 transceiver from Analog Devices with 20Mbps data rate, built-in +/-15kV ESD protection, in an MSOP-10 package, suitable for industrial communication networks.

Key Features

  • Supply voltage: 3.3V
  • Data rate: 20Mbps
  • ESD protection: +/-15kV HBM
  • Half and full duplex support
  • Supply current: 3mA
  • Driver output: +/-2.1V
Product Introduction: LTC2852IMS Product Introduction

The LTC2852IMS is a 3.3 V, 20 Mbps full-duplex RS485/RS422 transceiver from Analog Devices in a 10-lead MSOP package. It features one driver and one receiver, supporting up to 256 nodes per bus via one-eighth unit load receiver input impedance. Guaranteed failsafe receiver operation over the entire common-mode range ensures a logic-high output under open or shorted bus conditions. Enhanced ESD protection withstands plus or minus 15 kV HBM on transceiver pins without latchup. Current-limited drivers and thermal shutdown protect against bus contention, while micropower shutdown mode reduces supply current to 5 uA maximum.

Working Principle: LTC2852IMS Working Principle

The LTC2852IMS implements a full-duplex RS485/RS422 transceiver with independent driver and receiver signal paths operating simultaneously. The driver converts single-ended TTL/CMOS logic levels (applied to the DI pin) into differential RS485/RS422 output signals on the Y and Z pins. The driver output stage uses a current-limited H-bridge topology that drives the differential output voltage to a minimum of 1.5 V across a 54 Ohm load (two 120 Ohm termination resistors in parallel). The receiver monitors the differential voltage between the A and B pins and converts it to a single-ended logic level at the RO output. A 150 mV receiver hysteresis provides noise immunity on slowly transitioning bus signals. The receiver failsafe biasing ensures the RO output is high when the bus is idle (open or terminated but undriven). Driver and receiver enable pins (DE and RE) allow independent control. The micropower shutdown mode is entered when both DE is low and RE is high, reducing quiescent current to 5 uA. The thermal shutdown circuit disables the driver when the die temperature exceeds approximately 150 C, automatically re-enabling when the temperature drops.

Pin Description: LTC2852IMS Pin Definition and Functions
Pin Name Description
1 RO Receiver output; logic level corresponding to differential input A-B
2 RE Receiver enable; active low, high impedance output when high
3 DE Driver enable; active high, high impedance outputs when low
4 DI Driver input; TTL/CMOS compatible data input
5 GND Ground reference
6 Y Driver non-inverting output; RS485/RS422 bus line
7 Z Driver inverting output; RS485/RS422 bus line
8 B Receiver inverting input; connects to RS485/RS422 bus
9 A Receiver non-inverting input; connects to RS485/RS422 bus
10 VCC 3.3 V power supply (3.0 V to 3.6 V)
Application Scenarios: In which products and applications is LTC2852IMS used
  • Industrial RS485 Networks: Multi-node communication in factory automation with 256-node bus capability
  • Backplane Transceivers: High-speed 20 Mbps differential signaling across card cage backplanes
  • Level Translation: Converting between single-ended logic and differential RS422 signaling for cable drivers
  • Building Automation: BACnet MS/TP and Modbus RTU communication over RS485 cabling
  • Motor Drive Communication: Command and telemetry links between servo drives and host controllers
Alternative Models: What chips are recommended as replacements for LTC2852IMS
Model Manufacturer Rate Supply Duplex Package
LTC2851IMS Analog Devices 20 Mbps 3.3 V Half MSOP-8
SN65HVD74 Texas Instruments 20 Mbps 3.3 V Full SOIC-14
ADM3485EARZ Analog Devices 12 Mbps 3.3 V Half SOIC-8
THVD1550DR Texas Instruments 50 Mbps 3.3 V Half SOIC-8
ISL3179EIHZ Renesas 40 Mbps 3.3 V Full QSOP-16

LTC2852IMS is a 3.3V 20Mbps RS485/RS422 full-duplex transceiver from ADI in MSOP-10 with ±15kV ESD. The LTC2851IMS provides half-duplex operation in the same package. LTC2854IMS adds auto-direction control for simplified bus management. For 5V operation, LTC485 provides 250kbps RS485 with ±15kV ESD. The SN65HVD74DGKR from TI offers 3.3V 20Mbps full-duplex with ±30kV ESD as a pin-compatible alternative.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1