Opens in a new tab

MCP2515-I/ST

CAN controller, SPI interface, SOIC-18

5950

Effective Inventory

Image for reference only

Manufacturer Part:

MCP2515-I/ST

Package:

SOIC-18 (11.53 x 7.50 x 2.65 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

MCP2515-I/ST Overview

The MCP2515-I/ST is a stand-alone CAN 2.0B controller from Microchip communicating via SPI interface, with 3 transmit buffers and 2 receive buffers, in a TSSOP-20 package, widely used in automotive and industrial CAN bus systems.

Key Features

  • CAN 2.0B compliant
  • SPI interface (10MHz)
  • 3 transmit buffers
  • 2 receive buffers
  • 6 filters + 2 masks
  • Supply voltage: 2.7V-5.5V
  • Maximum clock: 40MHz
Product Introduction: MCP2515-I/ST Product Introduction

The MCP2515-I/ST is a stand-alone CAN (Controller Area Network) controller with SPI interface from Microchip Technology in a 20-pin TSSOP package. It implements CAN specification version 2.0B, supporting standard and extended data and remote frames at data rates up to 1 Mbps. The device features three transmit buffers with prioritization and abort capability, two receive buffers with prioritized message storage, six 29-bit acceptance filters, and two 29-bit acceptance masks for flexible message filtering. The high-speed 10 MHz SPI interface connects to any microcontroller, and the device is AEC-Q100 qualified for automotive applications. Operating from 2.7 V to 5.5 V, it is pin-compatible with the earlier MCP2510 with enhanced features.

Working Principle: MCP2515-I/ST Working Principle

The MCP2515-I/ST contains three main functional blocks: the CAN protocol engine, the message filtering and buffer management logic, and the SPI interface module. The CAN protocol engine handles bit timing, bit stuffing, CRC generation/checking, error management, and frame transmission/reception according to CAN 2.0B specifications. When the host MCU wants to transmit a message, it writes the identifier, data length, and data bytes into one of the three transmit buffers via the SPI interface, then sets the corresponding transmit request bit. The CAN engine selects the highest-priority buffer and transmits the frame on the bus. For reception, incoming messages are checked against the acceptance filters and masks; matching messages are stored in one of the two receive buffers. The first two data bytes can also be filtered, enabling protocol-specific message discrimination. When a valid message is received, the interrupt pin (INT) asserts to notify the host MCU. The one-shot mode ensures a message is only transmitted once per request, useful for time-triggered CAN protocols. The CLKOUT pin provides a programmable clock output derived from the oscillator for system use.

Pin Description: MCP2515-I/ST Pin Definition and Functions
Pin Name Description
1 TXCAN CAN transmit output; connects to CAN bus transceiver TXD input
2 RXCAN CAN receive input; connects to CAN bus transceiver RXD output
3 CLKOUT/SOF Clock output with programmable prescaler / Start-of-frame signal output
4 TX0RTS Transmit buffer 0 request-to-send; active low, can be used as general-purpose input
5 TX1RTS Transmit buffer 1 request-to-send; active low input
6 TX2RTS Transmit buffer 2 request-to-send; active low input
7 OSC2 Oscillator output; connect crystal or ceramic resonator
8 OSC1 Oscillator input; connect crystal or external clock source
9 VSS Ground
10 RX1BF Receive buffer 1 full flag; active low, can be used as general-purpose output
11 RX0BF Receive buffer 0 full flag; active low output
12 INT Interrupt output; active low, alerts MCU to received messages or errors
13 SCK SPI clock input; up to 10 MHz
14 SI SPI data input (MOSI); data from MCU to MCP2515
15 CS SPI chip select; active low, selects device for SPI communication
16 SO SPI data output (MISO); data from MCP2515 to MCU
17 VDD Power supply (2.7 V to 5.5 V)
18-20 NC No connect
Application Scenarios: In which products and applications is MCP2515-I/ST used
  • Automotive CAN Networks: Adding CAN bus capability to microcontrollers without integrated CAN peripherals
  • Industrial Automation: CAN-based sensor and actuator networks in factory floor equipment
  • Electric Vehicle BMS: Battery management system communication over CAN bus between cell monitoring ICs
  • Agricultural Machinery: ISOBUS and proprietary CAN communication in tractors and implements
  • Medical Device Networking: CAN bus data acquisition in hospital and clinical environments
Alternative Models: What chips are recommended as replacements for MCP2515-I/ST
Model Manufacturer Interface CAN Version Rate Package
MCP2515T-I/ST Microchip SPI 2.0B 1 Mbps TSSOP-20
MCP2518FD Microchip SPI CAN FD 8 Mbps TSSOP-20/VQFN-24
SJA1000 NXP Parallel 2.0B 1 Mbps SOIC-28
TJA1050 NXP N/A N/A 1 Mbps SOIC-8
TCAN4550 Texas Instruments SPI CAN FD 5 Mbps WQFN-24

MCP2515-I/ST is a standalone CAN 2.0B controller with SPI interface from Microchip in TSSOP-20. The MCP2515T-I/ST is the tape-and-reel version. MCP25625 integrates the CAN transceiver for a single-chip solution. For newer designs, MCP2517FD supports CAN FD (Flexible Data-rate) up to 8Mbps in the same TSSOP-20. The SJA1000 from NXP is the classic standalone CAN controller alternative in DIP-28 for legacy designs.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1