Opens in a new tab

NCP5500DT33RKG

onsemi 150mA 3.3V LDO, 3.5uA Iq, 40V max input, DPAK, enable pin

6012

Effective Inventory

Image for reference only

Manufacturer Part:

NCP5500DT33RKG

Package:

DPAK (DT suffix, Tab=VOUT)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The NCP5500DT33RKG from onsemi is a 150mA ultra-low quiescent current LDO regulator with a fixed 3.3V output. Featuring an exceptionally low 3.5uA ground current and wide 3.5V to 40V input range, it is specifically designed for always-on battery-powered and automotive applications where minimal standby power consumption is critical.

Key Specifications

Output Voltage 3.3V fixed (plus/minus 2% accuracy)
Max Output Current 150mA
Input Voltage Range 3.5V ~ 40V
Dropout Voltage 300mV (typical, 150mA load)
Quiescent Current 3.5uA (typical, no load)
Output Noise 60uVrms (10Hz~100kHz)
PSRR 75dB @ 1kHz
Enable Pin Active-high EN
Operating Temperature -40C ~ +125C

Features

  • Ultra-low 3.5uA quiescent current for long battery life
  • Wide 40V maximum input voltage for automotive transients
  • 75dB PSRR for clean output in noisy environments
  • Enable pin for power sequencing and standby control
  • Thermal shutdown and short-circuit current limiting
  • 60uVrms output noise suitable for RF and precision analog

Applications

  • Automotive body electronics and ECU standby power
  • Battery-powered IoT sensor nodes
  • Low-power microcontroller supply rails
  • Always-on power management in portable devices
  • Industrial 4-20mA loop-powered instruments
Product Introduction: NCP5500DT33RKG Product Introduction

The NCP5500DT33RKG from onsemi is a 150mA low-dropout linear regulator with a fixed 3.3V output, housed in a DPAK surface-mount package. The device stands out for its ultra-low quiescent current of 3.5uA typical, making it one of the most power-efficient LDOs in its class for always-on applications. The wide input voltage range of 3.5V to 40V accommodates automotive battery rails with full load-dump transient headroom. With a dropout voltage of only 300mV at 150mA, the NCP5500 can maintain regulation from a single Li-Ion cell or a 5V rail. The active-high enable pin allows external power sequencing or microcontroller-controlled shutdown, reducing system standby current to near-zero levels. The device also provides 75dB PSRR at 1kHz and only 60uVrms output noise, ensuring a clean supply for noise-sensitive RF and precision analog circuits.

Working Principle: NCP5500DT33RKG Working Principle

The NCP5500DT33RKG uses a P-channel MOSFET pass transistor controlled by an error amplifier that compares a fraction of the output voltage to an internal 1.23V bandgap reference. The feedback divider is internal for the fixed 3.3V output version. The enable (EN) pin controls the gate bias of the pass transistor; when EN is driven high (above 1.5V), the pass transistor is enabled and regulation begins. When EN is low (below 0.5V), the pass transistor is cut off, reducing the device current to sub-microamp levels. The thermal shutdown circuit disables the output when the junction temperature exceeds approximately 150C, while the short-circuit current limiter clamps the output current to approximately 200mA during fault conditions. The internal compensation network ensures stability with a 10uF output capacitor.

Pin Description: NCP5500DT33RKG Pin Definition and Functions
Pin Name Function
1 VIN Input Supply (3.5V ~ 40V)
2 GND Ground
3 EN Enable Input (active high)
Tab VOUT 3.3V Output / Thermal Pad
Application Scenarios: In which products and applications is NCP5500DT33RKG used
  • Automotive standby power: Maintain 3.3V MCU supply from the 12V battery bus with only 3.5uA drain during sleep mode
  • IoT sensor nodes: Power BLE or LoRa modules from a single Li-SOCl2 cell with minimal quiescent loss
  • Low-power MCU rails: Supply always-on microcontrollers in smart meters and building automation controllers
  • Portable medical devices: Regulate battery voltage for precision ADC reference rails with 60uVrms noise
  • 4-20mA loop instruments: Derive a clean 3.3V rail from the loop supply without loading the current loop
Alternative Models: What chips are recommended as replacements for NCP5500DT33RKG
Model Brand Iout Iq Vin Max
NCV5500DT33RKG onsemi 150mA 3.5uA 40V
TPS70933DBVR TI 150mA 1uA 30V
HT7133-1 Holtek 30mA 3uA 24V
ME6211A33M3G Microne 250mA 2.5uA 18V
XC6206P332MR Torex 200mA 1uA 6V

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1