Opens in a new tab

TPS7A4501DCQR

1A LDO, 20V, 35uVrms noise, 63dB PSRR, SOT-89-6

4200

Effective Inventory

Image for reference only

Manufacturer Part:

TPS7A4501DCQR

Package:

6-Pin SOT-89 (4.5 x 2.5 x 1.5 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TPS7A4501DCQR is a Texas Instruments 1A 20V LDO with 35uVrms output noise, 63dB PSRR at 1kHz, and 200mV dropout. Designed for noise-sensitive RF and analog loads. Packaged in 6-pin SOT-89, -40C to +125C.

Key Specifications

Output Current 1 A
Input Range 3.0 V to 20 V
Noise 35 uVrms (10Hz-100kHz)
PSRR 63 dB @ 1kHz
Dropout 200 mV @ 1A
Package SOT-89-6

Features

  • 1A output current
  • 35uVrms ultra-low noise
  • 63dB PSRR at 1kHz
  • 3.0V to 20V input range
  • 200mV dropout at 1A
  • NR pin for noise reduction
  • SOT-89-6 power package

Applications

  • RF and VCO power supply
  • High-speed ADC/DAC supply
  • Post-regulation after DC-DC
  • Test and measurement
Product Introduction: TPS7A4501DCQR Product Introduction

The TPS7A4501DCQR is a Texas Instruments 1A low-noise LDO regulator in a 6-pin SOT-89 power package, designed for noise-sensitive RF, analog, and precision applications. The 35uVrms output noise over 10Hz to 100kHz and 63dB PSRR at 1kHz make it one of the best LDOs for cleaning switching DC-DC converter output noise for RF VCOs, PLLs, and high-resolution data converters. The 3.0V to 20V input range supports post-regulation from common 5V, 12V, and 15V DC-DC outputs. The 200mV dropout at 1A provides good efficiency with moderate headroom. The NR (noise reduction) pin accepts an external capacitor (typically 0.01uF) that filters the internal reference noise, achieving the 35uVrms specification. An EN (enable) pin allows shutdown to reduce supply current. The SOT-89-6 package with exposed thermal pad provides low thermal resistance (34C/W typical) for 1A output at higher input-output differentials. The device is stable with ceramic output capacitors (2.2uF minimum). Packaged in SOT-89-6 rated for -40C to +125C.

Working Principle: TPS7A4501DCQR Working Principle

The TPS7A45 uses an NMOS pass transistor architecture with an internal charge pump to generate the gate voltage above the output. The NMOS architecture provides several advantages: very low output noise (since the noise is not multiplied by the pass element gain), high PSRR (the NMOS source-follower topology inherently rejects input noise), and fast transient response (the low output impedance of the source follower). The internal bandgap reference provides the target voltage, with the NR pin capacitor creating a low-pass filter that attenuates reference noise below the error amplifier bandwidth. The error amplifier drives the NMOS gate to maintain regulation. The charge pump generates the gate voltage from the input supply, requiring VIN at least 1.4V above VOUT for proper charge pump operation. During dropout (VIN-VOUT less than 200mV at 1A), the charge pump cannot fully enhance the NMOS, and the output voltage drops below the target. Current limit and thermal shutdown protect the device during fault conditions.

Pin Description: TPS7A4501DCQR Pin Definition and Functions
Pin Mnemonic Description
1 IN Input supply (3.0-20V)
2 NR Noise reduction (0.01uF cap)
3 EN Enable (active high)
4 GND Ground (exposed pad)
5 OUT Regulated output
6 NC No connect
Application Scenarios: In which products and applications is TPS7A4501DCQR used
  • RF VCO and PLL clean power supply with 35uVrms noise and 63dB PSRR for DC-DC cleanup
  • High-speed 16-bit ADC/DAC analog supply with low-noise post-regulation from 12V DC-DC
  • Post-regulation after switching converter for noise-sensitive test and measurement instruments
  • GPS receiver LNA supply with NR pin capacitor for ultra-low noise floor
Alternative Models: What chips are recommended as replacements for TPS7A4501DCQR
Model Manufacturer Key Difference
TPS7A4700 TI 1A, 4uVrms, even lower noise
TPS7A3501 TI 500mA, similar noise
LT3042 ADI 0.8uVrms, lower noise
ADM7150 ADI 1.6uVrms, 800mA

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1