Opens in a new tab

Home » Integrated Circuits ICs, Interface ICs » TPS1H100AQPWPRQ1

TPS1H100AQPWPRQ1

40V 100mohm auto high-side, adj Ilim, sense, HTSSOP-14

5500

Effective Inventory

Image for reference only

Manufacturer Part:

TPS1H100AQPWPRQ1

Package:

14-Pin HTSSOP (5.0 x 4.4 x 1.05 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TPS1H100AQPWPRQ1 is a Texas Instruments AEC-Q100 automotive 40V 100mohm single-channel smart high-side switch with adjustable current limit, accurate current sense, and full diagnostics. Version A with open-drain status. Packaged in HTSSOP-14, -40C to +125C.

Key Specifications

VDS 40 V
RDS(on) 100 mohm
Current Limit Adjustable via resistor
Current Sense +/-30mA @ 1A
AEC-Q100 Grade 1
Package HTSSOP-14

Features

  • 40V, 100mohm N-channel switch
  • AEC-Q100 Grade 1 qualified
  • Adjustable current limit
  • Accurate current sense (+/-30mA)
  • Full diagnostics (open/short)
  • Reverse battery protection
  • ISO 7637-2 transient immunity

Applications

  • Automotive load switching
  • Motor and solenoid control
  • Lighting and heater drive
  • Body control module
Product Introduction: TPS1H100AQPWPRQ1 Product Introduction

The TPS1H100AQPWPRQ1 is a Texas Instruments AEC-Q100 Grade 1 qualified single-channel smart high-side power switch in a 14-pin HTSSOP package, designed for automotive 12V/24V load driving applications. The 40V operating voltage and 100mohm RDS(on) handle typical automotive bus conditions including cold-crank and load-dump transients. The integrated NMOS power FET with charge-pump gate drive requires no external gate driver components. The adjustable current limit, set by an external resistor on the ILIM pin, protects loads and wiring with +/-20% accuracy. Version A provides an open-drain status output (STS) that reports fault conditions including overload, short-to-ground, open-load, and thermal shutdown. The accurate current sense output ( +-30mA at 1A) enables real-time load current monitoring for predictive diagnostics and smart power management. Full diagnostic coverage includes on-state and off-state open-load and short-to-battery detection, tested to AEC-Q100-12 Grade A with 1 million short-to-ground cycles. ISO 7637-2 and ISO 16750-2 electrical transient immunity is certified. Packaged in HTSSOP-14 with exposed thermal pad rated for -40C to +125C ambient, -40C to +150C junction.

Working Principle: TPS1H100AQPWPRQ1 Working Principle

The TPS1H100A uses an integrated N-channel MOSFET as the high-side switch element. An internal charge pump generates the gate voltage above the source (output) to fully enhance the NMOS, achieving the 100mohm RDS(on). The current sense circuit uses a sense FET technique that mirrors a small fraction of the load current to the SENSE pin, where an external resistor converts it to a proportional voltage. The current limit comparator monitors the load current and reduces the gate drive when the limit (set by the ILIM resistor) is exceeded, operating in constant-current mode. Thermal swing protection gradually reduces the current limit as junction temperature rises, preventing thermal runaway while maintaining partial operation. The diagnostic logic monitors the output voltage and current in both on and off states to detect open-load, short-to-battery, and short-to-ground conditions. The STS open-drain output pulls low when a fault is detected. An internal clamp protects against inductive load negative voltage spikes at turn-off. The EN pin control input is compatible with 3.3V and 5V microcontroller logic.

Pin Description: TPS1H100AQPWPRQ1 Pin Definition and Functions
Pin Mnemonic Description
1 VIN Input supply (3.5-40V)
2 EN Enable input
3 DIA_EN Diagnostic enable
4 ILIM Current limit resistor
5 GND Ground
6 STS Status output (open-drain)
7 SENSE Current sense output
8-10 VOUT Switch output to load
11-14 VIN Input supply (parallel)
Application Scenarios: In which products and applications is TPS1H100AQPWPRQ1 used
  • Automotive body control module load switching with full diagnostics and AEC-Q100 Grade 1
  • Motor and solenoid drive with adjustable current limit and inductive load clamp
  • LED lighting and heater control with accurate current sense for load monitoring
  • Automotive 12V/24V power distribution with ISO 7637-2 transient immunity
Alternative Models: What chips are recommended as replacements for TPS1H100AQPWPRQ1
Model Manufacturer Key Difference
TPS1H100BQPWPRQ1 TI Version B, analog current sense
TPS2H100 TI Dual channel version
INFINEON BTS50010 Infineon Similar auto high-side
NCR40500 onsemi Similar smart switch

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1