Opens in a new tab

Home » Integrated Circuits ICs, Interface ICs » CP2102N-A01-GQFN28

CP2102N-A01-GQFN28

USB-UART bridge, 3Mbaud, OTP, 4 GPIO, QFN-28

4800

Effective Inventory

Image for reference only

Manufacturer Part:

CP2102N-A01-GQFN28

Package:

28-Pin QFN (5.0 x 5.0 x 0.65 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The CP2102N-A01-GQFN28 is a Silicon Labs USB 2.0 full-speed to UART bridge controller with integrated transceiver, clock, and 1KB OTP for custom VID/PID. Supports up to 3Mbaud with 4 GPIO. Packaged in QFN-28, -40C to +85C.

Key Specifications

USB 2.0 Full-speed (12Mbps)
UART Baud Up to 3 Mbps
GPIO 4 configurable
OTP 1 KB
Supply 3.0V to 3.6V
Package QFN-28

Features

  • USB to UART bridge, no firmware
  • 3Mbaud data rate
  • Integrated 48MHz oscillator
  • 1KB OTP for custom VID/PID
  • 4 configurable GPIO pins
  • USB battery charger detection
  • Royalty-free VCP drivers

Applications

  • USB debug/programming port
  • IoT module interface
  • Industrial USB-to-serial
  • Consumer electronics
Product Introduction: CP2102N-A01-GQFN28 Product Introduction

The CP2102N-A01-GQFN28 is a Silicon Labs USB-to-UART bridge controller in a 28-pin QFN package, providing a complete USB 2.0 full-speed to RS-232/UART conversion solution without firmware development. The integrated USB transceiver eliminates external pull-up resistors, and the on-chip 48MHz oscillator eliminates the external crystal required by the original CP2102. The 1KB one-time programmable (OTP) memory allows customization of USB Vendor ID (VID), Product ID (PID), product description strings, and serial number for OEM branding and device identification. The UART supports baud rates from 300bps to 3Mbps with +/-1% accuracy across the range. Four configurable GPIO pins provide flexible control signals such as RTS, CTS, DTR, DSR, or custom handshaking. USB Battery Charger Detection (BCS 1.2) enables charging current negotiation when connected to USB host or charger ports. Remote wakeup capability allows the device to wake a suspended USB host. The 9.5mA operating current and sub-1uA USB suspend current support battery-powered applications. Royalty-free virtual COM port (VCP) drivers are available for Windows, macOS, Linux, and Android. Packaged in QFN-28 rated for -40C to +85C.

Working Principle: CP2102N-A01-GQFN28 Working Principle

The CP2102N integrates a USB 2.0 full-speed device controller, UART interface, and bridge logic in a single chip. The USB controller handles all USB protocol layers including device enumeration, endpoint management, and data transfer according to the Communication Device Class (CDC) Abstract Control Model (ACM) specification. The host operating system VCP driver creates a virtual COM port that applications access using standard serial API calls. The bridge logic transfers data between the USB bulk endpoints and the UART FIFOs, handling data format conversion (USB packet to UART frame) and flow control (RTS/CTS, DTR/DSR). The integrated 48MHz oscillator uses a precision RC oscillator calibrated at the factory, meeting USB full-speed clock tolerance requirements without an external crystal. The OTP memory stores USB descriptors (VID, PID, strings) that are read during USB enumeration. The GPIO pins are configured through OTP or runtime register access, mapping to UART modem control lines or general-purpose I/O. The voltage regulator accepts 5V VBUS and generates the internal 3.3V supply, with the VREGIN pin accepting 3.0-3.6V external supply.

Pin Description: CP2102N-A01-GQFN28 Pin Definition and Functions

28-pin QFN with key signals: D+/D- (USB data), VBUS (USB bus detect), VREGIN (3.0-3.6V supply), GND, TXD/RXD (UART data), RTS/CTS/DTR/DSR (modem control), GPIO0-GPIO3 (configurable), RST (reset), SUSPEND/SUSPEND-BAR (USB suspend indicators), NC (no connect). Refer to datasheet for complete 28-pin QFN ball map.

Application Scenarios: In which products and applications is CP2102N-A01-GQFN28 used
  • MCU debug and programming UART interface with custom VID/PID for OEM branding
  • IoT Wi-Fi/Bluetooth module USB programming port with 3Mbaud data transfer
  • Industrial USB-to-RS232/RS485 adapter with GPIO handshaking signals
  • Consumer electronics USB serial port with battery charger detection
Alternative Models: What chips are recommended as replacements for CP2102N-A01-GQFN28
Model Manufacturer Key Difference
CP2102-GM Silicon Labs Original, QFN-28, ext crystal
CP2104 Silicon Labs Single GPIO, smaller
FT232RL FTDI Similar USB-UART
CH340G WCH Lower cost alternative

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1