Opens in a new tab

TPS62175DQCR

28V 500mA buck, DCS-Control, 1MHz, 4.8uA sleep, WSON-10

7200

Effective Inventory

Image for reference only

Manufacturer Part:

TPS62175DQCR

Package:

10-Pin WSON (3.0 x 2.0 x 0.7 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The TPS62175DQCR is a Texas Instruments 28V 500mA synchronous buck converter with DCS-Control, 1MHz switching, 4.8uA sleep-mode IQ, power-good, and 100% duty cycle mode. Packaged in 10-pin WSON (3x2mm), -40C to +85C.

Key Specifications

Input Voltage 4.75 V to 28 V
Output Current 500 mA
Frequency 1 MHz
IQ (sleep) 4.8 uA
IQ (normal) 22 uA
Package WSON-10 (3x2mm)

Features

  • 4.75V to 28V input range
  • 500mA output current
  • DCS-Control topology
  • 1MHz fixed switching
  • 4.8uA sleep-mode IQ
  • 100% duty cycle mode
  • Power-good output

Applications

  • 12V/24V bus POL
  • Always-on housekeeping
  • Industrial sensor supply
  • Battery-powered systems
Product Introduction: TPS62175DQCR Product Introduction

The TPS62175DQCR is a Texas Instruments 28V 500mA synchronous step-down converter in a 10-pin WSON (3x2mm) package, using DCS-Control (Direct Control with Seamless transition) topology. The 4.75V to 28V input range supports 12V and 24V industrial bus rails and multi-cell Li-Ion battery packs. The DCS-Control topology provides fast transient response with no external compensation, using a constant on-time with adaptive off-time algorithm that seamlessly transitions between PWM and power-save modes. The 4.8uA quiescent current in sleep mode is among the lowest for 28V buck converters, making the TPS62175 ideal for always-on housekeeping supplies that must minimize standby power. The 100% duty cycle mode allows the output to follow the input when VIN drops near VOUT, maximizing dropout performance. The power-good output provides a reset signal for microcontroller power sequencing. Active output discharge pulls the output down when the converter is disabled, ensuring controlled shutdown. The 1MHz switching frequency enables small inductor and capacitor values for compact solution size. Packaged in 10-pin WSON rated for -40C to +85C.

Working Principle: TPS62175DQCR Working Principle

The TPS62175 uses DCS-Control topology, a TI proprietary constant on-time control scheme with a virtual inductor current emulator. The on-time is inversely proportional to VIN to maintain approximately constant switching frequency (1MHz). When the output voltage drops below the regulation threshold, the high-side MOSFET turns on for a fixed on-time, ramping up the inductor current. The off-time is adaptively controlled by the error amplifier output, which emulates the inductor current ripple. This emulated ripple provides the PWM ramp without requiring output voltage ripple, allowing the use of very low-ESR ceramic output capacitors. At light loads, the device enters power-save mode (PSM) where switching pulses are issued only when needed, reducing effective switching frequency and minimizing switching losses. In sleep mode (very light load), the IQ drops to 4.8uA by shutting down most internal bias circuits. The 100% duty cycle mode turns the high-side MOSFET on continuously when VIN approaches VOUT, eliminating switching losses and dropout. The power-good comparator monitors the FB pin and pulls PG low when the output is below 90% of the target.

Pin Description: TPS62175DQCR Pin Definition and Functions
Pin Mnemonic Description
1 VIN Input supply (4.75-28V)
2 EN Enable (active high)
3 PG Power-good (open-drain)
4 FB Feedback (0.8V reference)
5-8 GND Ground (exposed pad)
9 SW Switch node
10 BOOT Bootstrap capacitor
Application Scenarios: In which products and applications is TPS62175DQCR used
  • Industrial 24V bus to 3.3V POL with 4.8uA sleep-mode standby for always-on systems
  • 12V distributed power to 5V with power-good for MCU reset sequencing
  • Battery-powered instrument 12V to 3.3V with 100% duty cycle dropout operation
  • Industrial sensor supply from 24V rail with DCS-Control fast transient response
Alternative Models: What chips are recommended as replacements for TPS62175DQCR
Model Manufacturer Key Difference
TPS62170DQCR TI Lower IQ, 300mA
TPS62173DQCR TI Fixed 3.3V output
LMR16006 TI Similar 28V, 600mA
MP2359 MPS Similar 24V buck

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1