Opens in a new tab

MP28164GD-Z

4.2A buck-boost, 1.2-5.5V in, 2MHz, 25uA IQ, QFN-11

1391

Effective Inventory

Image for reference only

Manufacturer Part:

MP28164GD-Z

Package:

11-Pin QFN (2.0 x 3.0 x 0.65 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The MP28164GD-Z is a Monolithic Power Systems (MPS) 4.2A single-inductor buck-boost converter with 1.2-5.5V input, 1.5-5V output, 2MHz switching, 25uA IQ, and power-good. Packaged in QFN-11 (2x3mm), -40C to +125C.

Key Specifications

Input Voltage 1.2 V to 5.5 V
Output Voltage 1.5 V to 5 V
Current 4.2 A switch limit
Frequency 2 MHz
IQ 25 uA typical
Package QFN-11 (2x3mm)

Features

  • Single-inductor buck-boost topology
  • 1.2V to 5.5V input range
  • 1.5V to 5V adjustable output
  • 4.2A switch current limit
  • 2MHz fixed switching
  • 25uA quiescent current
  • Power-good output

Applications

  • Li-Ion battery-powered devices
  • Portable electronics
  • USB power delivery
  • IoT and wearable
Product Introduction: MP28164GD-Z Product Introduction

The MP28164GD-Z is a Monolithic Power Systems (MPS) high-efficiency single-inductor buck-boost converter in a compact QFN-11 (2x3mm) package. The single-inductor topology seamlessly transitions between buck, boost, and buck-boost modes, maintaining a regulated output whether the input voltage is above, below, or equal to the output – ideal for Li-Ion battery-powered systems where the battery voltage ranges from 2.7V to 4.2V. The 1.2V to 5.5V input range supports operation from deeply discharged batteries and 5V USB sources. The 1.5V to 5V output range covers common system rails (1.8V, 2.5V, 3.3V, 5V). The 4.2A switch current limit provides 2A output current at 3.3V from a 2.5V to 5.5V input. The 2MHz fixed switching frequency minimizes inductor and capacitor size for compact portable designs. The 25uA quiescent current maximizes battery life during light-load operation. Selectable PFM/PWM mode trades off light-load efficiency (PFM) vs. low ripple (PWM). The power-good output indicates output regulation status. Hiccup-mode short-circuit protection and thermal shutdown handle fault conditions. The -Z suffix indicates tape-and-reel packaging. Packaged in QFN-11 rated for -40C to +125C.

Working Principle: MP28164GD-Z Working Principle

The MP28164 uses a single-inductor four-switch (S4) buck-boost topology with four integrated MOSFET switches (SWA, SWB, SWC, SWD) and one external inductor. In buck mode (VIN > VOUT), SWA/SWB PWM switch while SWD remains on and SWC off, operating as a synchronous buck converter. In boost mode (VIN < VOUT), SWC/SWD PWM switch while SWA remains on and SWB off, operating as a synchronous boost converter. In buck-boost mode (VIN approximately equal to VOUT), all four switches operate in each cycle to transfer energy. The control loop uses a current-mode PWM with a fixed 2MHz clock. An internal voltage reference and error amplifier maintain output regulation across all three operating modes with seamless transitions. The mode transitions include hysteresis to prevent chattering at the boundary. In PFM mode at light loads, the converter skips pulses to reduce effective switching frequency and switching losses. The internal soft-start ramps the reference voltage over 4ms, limiting inrush current. The PG comparator asserts when the output reaches 90% of the target voltage.

Pin Description: MP28164GD-Z Pin Definition and Functions
Pin Mnemonic Description
1 VIN Input supply (1.2-5.5V)
2 VCC Internal supply bypass
3 EN Enable (active high)
4 FB Feedback (sets VOUT)
5 MODE/SYNC PFM/PWM mode or ext sync
6 PG Power-good (open-drain)
7 SW2 Switch node 2
8 SW1 Switch node 1
9-11 GND/NC Ground / No connect
Application Scenarios: In which products and applications is MP28164GD-Z used
  • Li-Ion battery 3.7V to 3.3V system supply with seamless buck-boost across full battery range
  • Portable electronics USB or battery dual-source with 2A output at 3.3V
  • Wearable device 1.8V rail from single-cell Li-Ion with 25uA IQ standby
  • IoT sensor node 5V output from 3.3V USB with boost capability
Alternative Models: What chips are recommended as replacements for MP28164GD-Z
Model Manufacturer Key Difference
MP28164GD-P MPS Same, different reel size
TPS63020 TI Similar buck-boost
LTC3534 ADI Similar buck-boost
BQ25570 TI Nano-power boost

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1