Opens in a new tab

BTS5090-1EJA

Single-channel smart high-side power switch, 90mΩ, 3A, 5-28V, DSO-8 EP, Infineon PROFET+ 12V, analog sense, AEC-Q100

12400

Effective Inventory

Image for reference only

Manufacturer Part:

BTS5090-1EJA

Package:

PG-DSO-8-43-EP (8-pin dual small outline package, 3.9mm width, exposed thermal pad, 1.27mm pitch)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The BTS5090-1EJA is a single-channel smart high-side power switch from Infineon Technologies, part of the PROFET™+ 12V family of intelligent power devices. Fabricated in Infineon’s Smart6 technology, this device integrates a 90 mΩ N-channel vertical power MOSFET with comprehensive protection, diagnostic, and control circuitry on a single monolithic chip.

Designed specifically for automotive 12V systems, the BTS5090-1EJA operates from a supply voltage of 5 V to 28 V and can handle nominal load currents up to 3 A. The device provides an accurate proportional current sense output (IS pin) with a typical sense ratio kILIS of 1500, enabling the system controller to monitor the load current for diagnostic and control purposes.

Housed in a PG-DSO-8-43-EP package with an exposed thermal pad, the BTS5090-1EJA offers a rich set of protection features including overcurrent limitation (20 A min), thermal shutdown with dynamic temperature limitation, overvoltage protection, undervoltage shutdown, loss of ground protection, and reverse polarity protection capability with an external resistor. The device is AEC-Q100 qualified and designed to drive lamps up to P21W, LEDs, and other loads in harsh automotive environments.

Key Specifications

Parameter Value
Number of Channels 1 (single high-side)
RDS(on) @ 25°C 90 mΩ typical
RDS(on) @ 150°C 180 mΩ maximum
Nominal Load Current 3 A
Short-Circuit Current Limit (ILIM) 20 A minimum
Operating Supply Voltage (VS) 5 V to 28 V
Load Dump Voltage (max) 41 V
Logic Input Compatibility 3.3 V / 5 V CMOS
Current Sense Ratio (kILIS) 1500 typical
Diagnostic Type Analog proportional sense (IS pin)
Open Load Detection ON-state and OFF-state
Turn-ON Time (ton) 230 µs max
Turn-OFF Time (toff) 230 µs max
Standby Current 0.5 µA typical (OFF state)
Operating Junction Temperature –40°C to +150°C
Package PG-DSO-8-43 EP (exposed pad)
Qualification AEC-Q100, Automotive Grade

Features

  • Single-channel smart high-side power switch, 90 mΩ RDS(on)
  • PROFET™+ 12V family with Smart6 technology
  • Nominal load current: 3 A
  • Wide operating voltage: 5 V to 28 V (41 V load dump)
  • Proportional current sense output (kILIS ≈ 1500)
  • Overcurrent protection with dynamic limitation
  • Thermal shutdown with dynamic temperature limitation
  • Open load detection in ON and OFF states
  • Short-circuit to ground and battery protection
  • Undervoltage shutdown with hysteresis
  • Overvoltage protection
  • Loss of ground protection
  • Reverse polarity protection (with external resistor)
  • 3.3 V / 5 V CMOS compatible logic input
  • ESD protection (2 kV HBM)
  • Very low standby current (0.5 µA)
  • PG-DSO-8-43-EP package with exposed thermal pad
  • AEC-Q100 qualified, automotive grade
  • RoHS compliant and green product

Applications

  • Automotive body electronics and lighting control
  • Interior and exterior lighting (P21W lamps, LED modules)
  • Door module and seat actuator drivers
  • HVAC blower and flap motor control
  • Relay and solenoid drivers
  • Industrial 12V/24V power distribution
  • Replaces mechanical relays and fuses
  • DC motor drivers for low-current applications
Product Introduction: BTS5090-1EJA Product Introduction

The BTS5090-1EJA is a single-channel intelligent high-side power switch from Infineon Technologies’ PROFET™+ 12V product family. Fabricated using Infineon’s Smart6 power technology, this device integrates an N-channel vertical power MOSFET with charge pump, control logic, protection circuitry, and diagnostic functions all on a single monolithic chip.

With an on-state resistance of typically 90mΩ (180mΩ max at 150°C junction temperature), the BTS5090-1EJA can drive continuous load currents up to 3A in a compact PG-DSO-8 package with exposed pad. It is specifically designed for automotive 12V systems, with an operating voltage range from 5V to 28V and the ability to withstand load dump transients up to 41V.

A key feature is the proportional current sense output (IS pin), which provides an accurate scaled-down representation of the load current with a typical sense ratio kILIS of 1500:1. This enables precise load current monitoring for system diagnostics, bulb outage detection, and overload protection without the need for external current sense resistors.

The device offers comprehensive protection including active overcurrent limitation, dynamic thermal shutdown with temperature limitation, undervoltage lockout, overvoltage protection, open load detection in both ON and OFF states, and loss of ground protection. Reverse battery protection can be implemented with a single external resistor.

Qualified to AEC-Q100 automotive standards and specified over the full junction temperature range of -40°C to +150°C, the BTS5090-1EJA is ideal for automotive body electronics applications including lighting control, door modules, seat electronics, and HVAC systems. Infineon guarantees long-term supply availability, with production planned through at least 2034.

Working Principle: BTS5090-1EJA Working Principle

The BTS5090-1EJA operates as an intelligent high-side power switch that controls and protects power delivery to a load connected between the output pin and ground. Here are the key functional blocks:

1. Power Stage: The main switching element is an N-channel vertical power MOSFET with 90mΩ on-resistance. Since it is a high-side configuration (the MOSFET sits between supply and load), an internal charge pump generates a voltage above VS to properly turn on the N-channel MOSFET gate. The charge pump is integrated on-chip and requires no external components.

2. Input Logic: The IN pin accepts CMOS/TTL logic levels compatible with both 3.3V and 5V microcontrollers. A logic high turns the channel on; a logic low turns it off. The input includes hysteresis for noise immunity in electrically noisy environments. An ESD protection structure on the input pin ensures robustness against electrostatic discharge events.

3. Current Sense Circuitry: A small fraction of the load current (typically 1/1500th) is mirrored to the IS (sense) output pin. This proportional current sense signal allows the external microcontroller to monitor the actual load current by measuring the voltage across a sense resistor connected from IS to ground. The sense ratio kILIS is tightly controlled for accurate current measurement.

4. Overcurrent Protection: In the event of a short circuit or severe overload, the active current limiting circuit clamps the output current at approximately 20A minimum. This prevents damage to both the device and the load during fault conditions, while the thermal protection takes over for sustained faults.

5. Thermal Protection: The device monitors its own junction temperature. If the temperature exceeds the thermal shutdown threshold, the power switch is turned off. Dynamic temperature limitation provides controlled restart behavior, cycling the output on and off to maintain safe junction temperature during sustained overload conditions, rather than latching off completely.

6. Open Load Detection: The device can detect open-load conditions (load disconnected or burned out) both when the output is ON and when it is OFF. In the OFF state, a small sense current flows to detect whether the load is present. This is particularly useful for detecting burned-out bulbs in automotive lighting applications.

7. Undervoltage and Overvoltage Protection: If the supply voltage drops below the undervoltage threshold (approximately 5V), the device shuts down to prevent undefined operation. Similarly, overvoltage protection activates during load dump conditions, clamping the output to safe levels.

8. Loss of Ground Protection: If the ground pin becomes disconnected, the device’s internal circuitry ensures that the output turns off safely and does not present a hazard, with the output voltage limited to a safe level determined by the input voltage.

Pin Description: BTS5090-1EJA Pin Definition and Functions
Pin No. Pin Name Type Function
1 IN Input Logic input for channel control. High = ON, Low = OFF. 3.3V/5V CMOS compatible with hysteresis. Connect to microcontroller GPIO.
2 GND Ground Logic ground. Connect to system ground plane. Note: Logic ground is separate from power ground internally for improved accuracy.
3 IS Output Analog current sense output. Provides a proportional current mirror of the load current (kILIS ≈ 1500:1). Connect to ground through a sense resistor for current monitoring. Also indicates fault conditions (open load, over-temperature, etc.).
4 OUT Power Output High-side switch output. Connect to the load. Load other side connects to ground. Rated up to 3A continuous.
5 OUT Power Output Additional output pin, internally parallel to pin 4. Both pins must be connected together to the load for proper current handling and thermal performance.
6 VS / VBB Power Supply voltage input (5V to 28V operating, 41V max load dump). Connect to battery/12V rail. Bypass with 100nF ceramic capacitor to GND, placed close to pin.
7 VS / VBB Power Additional supply pin, internally parallel to pin 6. Both pins must be connected together to the supply voltage for proper operation.
8 VS / VBB Power Additional supply pin, internally parallel to pin 6 and 7. All three VS pins must be connected together.
Pad Exposed Pad Thermal/Power Exposed thermal pad on the bottom of the package. Must be soldered to PCB copper area for heat dissipation. Internally connected to VS (supply voltage).

Package: PG-DSO-8-43-EP (Plastic Dual Small Outline package, 8 leads, 3.9mm body width, 4.9mm body length, 1.27mm lead pitch, exposed pad on bottom). The exposed pad is internally connected to the VS (supply) potential.

Application Scenarios: In which products and applications is BTS5090-1EJA used
  • Automotive Lighting Control: Driving exterior and interior lighting including P21W bulbs, W5W indicator lamps, and LED modules in body control modules (BCMs), headlight units, and lighting control units, with open-load detection for bulb-out monitoring and diagnostic reporting to the vehicle CAN bus.
  • Door Modules and Seat Electronics: Controlling door lock actuators, window lift motors, mirror adjusters, seat adjustment motors, and heating elements in automotive door modules and seat control units, where the integrated protection features enhance reliability in harsh automotive environments.
  • HVAC Blower and Flap Control: Driving HVAC blower motors, air flap actuators, and recirculation motors in climate control systems, with current sensing enabling stall detection and motor health monitoring for predictive maintenance.
  • Relay and Solenoid Replacement: Replacing electromechanical relays and fuses in automotive and industrial power distribution systems, providing superior reliability (no mechanical wear), faster response, diagnostic capabilities, and reduced PCB space requirements.
  • Industrial 12V/24V Power Distribution: Intelligent load switching in factory automation equipment, PLC output modules, industrial sensors, and 24V control systems, where overcurrent and thermal protection protect both the equipment and wiring from damage.
  • Automotive Auxiliary Power Outlets: Controlling 12V power outlets (cigarette lighter sockets), USB charging ports, and accessory power rails in passenger vehicles and trucks, with built-in overcurrent protection eliminating the need for external fuses.
  • Small DC Motor Drivers: Driving low-current DC motors and gear motors in applications such as small pump controls, valve actuators, and positioning mechanisms, where the current sense output can be used for stall detection and torque monitoring.
  • Truck and Commercial Vehicle Electronics: Power distribution and load control in 24V commercial vehicle systems (within 28V max rating), including dashboard controls, lighting modules, and auxiliary equipment control in trucks, buses, and agricultural machinery.
Alternative Models: What chips are recommended as replacements for BTS5090-1EJA
Manufacturer Part Number Channels RDS(on) Iout Package Notes
Infineon BTS5090-1EJB 1 90 mΩ 3 A DSO-8 EP Same device, different ordering code
Infineon BTS5200-1EJA 1 200 mΩ 1.5 A DSO-8 EP Lower current, lower cost option
Infineon BTS7200-2EPA 2 66 mΩ/ch 1.2 A/ch TSDSO-14 Dual channel, PROFET+2 generation
Infineon BTS5210L 2 140 mΩ/ch 2.4 A/ch DSO-12 Dual channel, 24V classic PROFET
STMicro VN920 1 100 mΩ 3 A TO-252-5 Single channel, through-hole/DDPAK
TI TPS1H000A 1 80 mΩ 2.7 A SOIC-8 TI smart high-side switch

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1