Opens in a new tab

NTB0104BQ-Q100X

AEC-Q100 4-bit auto-direction level translator, 1.2-3.6V/1.65-5.5V, 100MHz, DHVQFN-14

3487

Effective Inventory

Image for reference only

Manufacturer Part:

NTB0104BQ-Q100X

Package:

DHVQFN-14 (2.5 x 3 x 0.85 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The NTB0104BQ-Q100X is an NXP AEC-Q100 qualified 4-bit dual-supply voltage level translator with auto-direction sensing and 3-state outputs. It enables bidirectional voltage level translation between any low-voltage nodes (1.2V to 5.0V) with up to 100MHz bandwidth, making it ideal for automotive SPI and I2C bus voltage bridging.

Key Specifications

Number of Channels 4-bit bidirectional
VCC(A) Supply Range 1.2V to 3.6V
VCC(B) Supply Range 1.65V to 5.5V
Propagation Delay 5.9ns typ. @ 1.2V/1.8V
Bandwidth Up to 100MHz
Output Type 3-State, Push-Pull
Supply Current 3.5μA typ.
ESD Protection HBM >2.5kV (A port), >15kV (B port)
Operating Temperature -40°C to +125°C
Qualification AEC-Q100

Features

  • AEC-Q100 qualified for automotive applications
  • Auto-direction sensing (no direction control pin needed)
  • Bidirectional voltage translation between any low-voltage nodes
  • Wide supply ranges: VCC(A) 1.2-3.6V, VCC(B) 1.65-5.5V
  • I_OFF circuitry for partial power-down operation
  • Inputs accept voltages up to 5.5V
  • High ESD protection: HBM >15kV on B port
  • 3-state output enable (OE) for bus isolation
  • Low quiescent current: 3.5μA typical
  • Available in DHVQFN-14 (2.5 x 3 x 0.85 mm)

Applications

  • Automotive SPI bus level shifting (3.3V MCU to 5V peripheral)
  • I2C voltage bridging between domains
  • Push-pull signal level translation
  • Automotive infotainment system bus interfacing
  • ADAS sensor interface voltage adaptation
Product Introduction: NTB0104BQ-Q100X Product Introduction

The NTB0104BQ-Q100X is an NXP AEC-Q100 qualified 4-bit dual-supply voltage level translator with auto-direction sensing and 3-state outputs. It enables bidirectional translation between any low-voltage nodes from 1.2V to 5.0V (VCC(A): 1.2-3.6V, VCC(B): 1.65-5.5V) at up to 100MHz bandwidth. The auto-direction sensing eliminates the need for a direction control pin, simplifying PCB layout. Features include I_OFF partial power-down support, 15kV HBM ESD on the B port, 3.5μA quiescent current, and OE pin for bus isolation. Available in DHVQFN-14 (2.5x3mm) package.

Working Principle: NTB0104BQ-Q100X Working Principle

The NTB0104BQ-Q100X uses a one-shot enhanced auto-direction sensing architecture. Each channel monitors both the A and B ports for transitions. When a low-to-high or high-to-low transition is detected on one side, the device activates the corresponding driver on the opposite side and fires a one-shot pulse to accelerate the edge. After the transition, the device returns to a high-impedance monitoring state, ready for the next edge from either direction. This auto-direction sensing eliminates the need for a direction control signal, making the device transparent to the bus protocol. The OE pin, when asserted low, places all outputs in a high-impedance 3-state condition, allowing bus isolation during system power-up or diagnostics. The I_OFF circuitry ensures that when either supply is removed, the outputs are disabled and no damaging backflow current flows through the device.

Pin Description: NTB0104BQ-Q100X Pin Definition and Functions
Pin Mnemonic Description
1 OE Output enable (active high; low = high-Z)
2 A1 Channel 1 port A I/O
3 GND Ground
4 A2 Channel 2 port A I/O
5 A3 Channel 3 port A I/O
6 A4 Channel 4 port A I/O
7 VCC(A) Port A supply (1.2-3.6V)
8 B1 Channel 1 port B I/O
9 B2 Channel 2 port B I/O
10 B3 Channel 3 port B I/O
11 B4 Channel 4 port B I/O
12 VCC(B) Port B supply (1.65-5.5V)
13 GND Ground
14 NC Not connected (thermal pad)
Application Scenarios: In which products and applications is NTB0104BQ-Q100X used
  • Automotive SPI bus level shifting from 3.3V MCU to 5V peripheral with auto-direction
  • I2C voltage bridging between 1.8V sensor and 3.3V MCU domains
  • ADAS sensor interface adaptation from 1.8V camera to 3.3V processor
  • Automotive infotainment system UART/SPI bus between 3.3V SoC and 5V CAN controller
  • General push-pull signal level translation with OE for bus isolation during flash programming
Alternative Models: What chips are recommended as replacements for NTB0104BQ-Q100X
Model Manufacturer Key Difference
NTB0104BQ,115 NXP Non-AEC-Q100 version (commercial grade)
NXB0104BQ-Q100X Nexperia Pin-compatible AEC-Q100 alternative
TXB0104PWR TI 4-bit auto-direction, non-automotive
PCA9306 NXP 2-bit I2C level shifter, open-drain
SN74LVC1T45 TI 1-bit direction-controlled translator

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1