Opens in a new tab

LT1534IS-1#TRPBF

Low-noise isolated push-pull DC-DC controller, 2.7-30V, slew-rate EMI control, 16-SSOP, for medical/industrial

2196

Effective Inventory

Image for reference only

Manufacturer Part:

LT1534IS-1#TRPBF

Package:

16-SSOP (6.2 x 5.3 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The LT1534IS-1#TRPBF is an Analog Devices (Linear Technology) low-noise isolated DC-DC converter controller that uses proprietary edge-slowing techniques to dramatically reduce conducted and radiated EMI. With push-pull isolated output capability and adjustable slew rate control, it enables compact isolated power supplies that meet stringent EMI requirements without filtering.

Key Specifications

Input Voltage 2.7V to 30V
Switching Frequency 20 kHz to 250 kHz (adjustable)
Topology Push-pull isolated
Gate Drive External MOSFETs (push-pull)
Output Isolation Transformer-isolated output
EMI Control Adjustable voltage/current slew rate
Output Voltage Isolated, set by transformer turns ratio
Operating Temperature -40°C to +85°C (I-grade)
Package 16-SSOP (0.154″ width)

Features

  • Proprietary edge-slowing technology reduces high-frequency harmonic content by 20-40 dB
  • Independent voltage and current slew rate control pins for EMI optimization
  • Push-pull topology provides isolation and high efficiency in compact transformers
  • Adjustable switching frequency from 20 kHz to 250 kHz for design flexibility
  • Cycle-by-cycle current limiting for overload protection
  • Soft-start capability limits inrush current during power-up

Applications

  • Medical equipment isolated power supply with low EMI
  • Industrial process control isolated sensor power
  • Isolated RS-485/CAN transceiver power supply
  • Automotive isolated gate driver bias supply
  • Aerospace low-EMI isolated converter
Product Introduction: LT1534IS-1#TRPBF Product Introduction

The LT1534IS-1#TRPBF is an Analog Devices (Linear Technology) low-noise isolated DC-DC converter controller that uses patented edge-slowing technology to reduce switching transition dv/dt and di/dt, dramatically lowering conducted and radiated EMI without additional filtering. Operating from 2.7V to 30V input with adjustable 20-250 kHz switching frequency, the push-pull topology drives an isolation transformer to create a fully isolated output. The independent VSLEW and ISLEW pins allow designers to optimize the voltage and current slew rates for minimum EMI while maintaining efficiency, making it ideal for medical, industrial, and aerospace isolated power supplies.

Working Principle: LT1534IS-1#TRPBF Working Principle

The LT1534 controls external MOSFET switches in a push-pull configuration to drive the primary winding of an isolation transformer. The key innovation is the edge-slowing circuit: the VSLEW pin sets the maximum dv/dt rate of the switch node voltage, and the ISLEW pin sets the maximum di/dt rate of the switch current. By limiting these slew rates, the harmonic content of the switching waveforms is dramatically reduced — harmonics above the slew-rate-determined corner frequency are attenuated by 20-40 dB compared to hard-switched converters. This allows the converter to pass EMI compliance tests without common-mode chokes or shielded transformers, reducing BOM cost and solution size.

Pin Description: LT1534IS-1#TRPBF Pin Definition and Functions
Pin Function
VIN Input power supply (2.7-30V)
CSET Switching frequency set capacitor
VSLEW Voltage slew rate set resistor (dv/dt control)
ISLEW Current slew rate set resistor (di/dt control)
A1 / A2 Push-pull gate drive outputs for external MOSFETs
FB Feedback input from isolated output (via optocoupler)
COMP Loop compensation pin
SENSE Current sense input for overcurrent protection
GND Ground
Application Scenarios: In which products and applications is LT1534IS-1#TRPBF used
  • Medical patient monitoring equipment 5W isolated power supply with IEC 60601 EMI compliance
  • Industrial 4-20mA loop isolated sensor power (3.3V/5V output)
  • RS-485/CAN bus isolated transceiver bias supply in noisy environments
  • IGBT/SiC gate driver isolated bias supply for motor drives
  • Aerospace avionics low-EMI isolated converter for sensitive RF systems
Alternative Models: What chips are recommended as replacements for LT1534IS-1#TRPBF
Model Manufacturer Key Difference
LT1533IS ADI Higher current dual-output variant
LT3999 ADI Higher voltage push-pull transformer driver
LM5022 Texas Instruments Push-pull controller without EMI control
MAX253 ADI Simpler isolated RS-485 supply driver
DCH010505S Murata Complete 1W isolated DC-DC module

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1