Opens in a new tab

DS9503P+T&R

1-Wire ESD protection diode with 2×5Ω isolation resistors, snapback Zener, >27kV, TSOC-6 T&R

14269

Effective Inventory

Image for reference only

Manufacturer Part:

DS9503P+T&R

Package:

TSOC-6 (Surface Mount)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The DS9503P+T&R from Analog Devices (formerly Maxim Integrated) is an ESD protection diode with integrated 5 Ω isolation resistors designed specifically for 1-Wire interface protection. Featuring a snapback (fast-recovery) Zener characteristic that clamps ESD events to safe voltage levels, it raises ESD protection to over 27 kV (IEC 801-2) when used with circuits that already have basic ESD protection. The device is housed in a TSOC-6 surface-mount package and is tape-and-reel packaged for automated assembly.

Key Specifications

Protection Target 1-Wire interface
ESD Protection Level >27 kV (IEC 801-2, with existing protection)
Isolation Resistors 2 x 5 Ω (integrated)
Trigger Voltage ~9 V (snapback Zener)
Holding Voltage ~6 V (fast-recovery mode)
Leakage Current Low (normal operation)
Capacitance Low (minimizes signal degradation)
Failure Mode Short circuit (fail-safe)
Operating Temperature Industrial range
Package TSOC-6 (Tape & Reel)
Compatible Logic All 5 V logic families

Features

  • Snapback (fast-recovery) Zener characteristic for effective ESD clamping
  • Two integrated 5 Ω isolation resistors for additional circuit protection
  • Compatible with all 5 V logic families
  • Fail-safe short-circuit failure mode protects downstream circuitry
  • Low capacitance avoids 1-Wire signal degradation

Applications

  • 1-Wire iButton reader ESD protection
  • iButton smart key and access control systems
  • Temperature sensor (DS18B20) 1-Wire bus protection
  • Industrial 1-Wire network surge protection
  • Medical device 1-Wire interface ESD protection
Product Introduction: DS9503P+T&R Product Introduction

The DS9503P+T&R from Analog Devices is an ESD protection diode designed specifically for 1-Wire interface applications. Compared to the DS9502, the DS9503 integrates two 5 Ω isolation resistors that provide additional circuit protection during ESD events. During normal operation, the 5 Ω resistors are negligible for 1-Wire communication. However, during an ESD strike, the resistors present a relatively high impedance compared to the conducting snapback diode, forcing the ESD energy through the diode and isolating the protected circuit on the other side. The snapback (fast-recovery) Zener characteristic means that once the trigger voltage is exceeded, the device enters a low-voltage holding state, effectively clamping the transient. If an extreme ESD event exceeds the device’s maximum rating, the DS9503 fails short, providing fail-safe protection.

Working Principle: DS9503P+T&R Working Principle

The DS9503P+T&R operates through a snapback Zener mechanism: (1) Normal Operation — the device presents a high impedance with low leakage current and low capacitance, not affecting 1-Wire communication through the 5 Ω series resistors; (2) ESD Trigger — when a voltage transient exceeds the trigger voltage (~9 V), the internal Zener junction avalanches and the device enters snapback mode, where the voltage drops to the holding voltage (~6 V) while conducting high current; (3) Energy Absorption — the ESD energy is dissipated in the Zener junction while the 5 Ω resistors isolate the protected circuit side from the ESD event on the 1-Wire line side; (4) Recovery — when the transient current drops below the holding current, the device exits snapback and returns to high-impedance state; (5) Fail-Safe — if the ESD energy exceeds the device’s absorption capability, the junction fuses into a permanent short circuit, ensuring the protected circuit is not exposed to dangerous voltages.

Pin Description: DS9503P+T&R Pin Definition and Functions
Pin Function
1 (1-Wire side) 1-Wire data line connection with 5 Ω series resistor
2 (GND) Ground connection
3 (1-Wire side) 1-Wire data line return with 5 Ω series resistor
4 (Protected side) Protected circuit connection (downstream of 5 Ω resistor)
5 (GND) Ground connection
6 (Protected side) Protected circuit return (downstream of 5 Ω resistor)
Application Scenarios: In which products and applications is DS9503P+T&R used
  • iButton access control reader protecting the 1-Wire probe from >27 kV ESD discharge events
  • DS18B20 temperature sensor network with DS9503 at each node protecting against cable discharge
  • Industrial 1-Wire bus protecting the master transceiver from ESD on long cable runs
  • Electronic lock system with iButton key reader ESD protection for reliable operation
  • Medical patient monitoring device 1-Wire sensor interface with fail-safe ESD protection
Alternative Models: What chips are recommended as replacements for DS9503P+T&R
Model Manufacturer Key Difference
DS9502P+T&R Analog Devices ESD protection without isolation resistors
DS9503P+ Analog Devices Same device, cut-tape packaging
TVS0500DMVR TI General-purpose ESD protection, 5 V working voltage
PESD5V0S1BA Nexperia Generic 5 V ESD protection diode
TPD4E05U06 TI Quad-channel ESD protection for multi-line interfaces

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1