Opens in a new tab

AP7365-33WG-7

3.3V Fixed LDO, 600mA, 35uA Iq, 65dB PSRR, SOT-25

13688

Effective Inventory

Image for reference only

Manufacturer Part:

AP7365-33WG-7

Package:

SOT-25 / SC-74A / SOT-753 (2.9 x 1.6 x 1.1 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The AP7365-33WG-7 from Diodes Incorporated is a 600 mA, 3.3 V fixed-output low-dropout linear regulator with 35 uA quiescent current, 65 dB PSRR, and enable control in a SOT-25 package.

Key Specifications

Type Fixed 3.3V LDO Linear Voltage Regulator
Output Voltage 3.3 V (fixed)
Output Current 600 mA
Input Voltage Range 2.0 V to 6.0 V
Dropout Voltage 300 mV (typical) @ 600mA
Quiescent Current (Iq) 35 uA (typical)
PSRR 65 dB @ 1kHz
Load Regulation 1%
Enable Control Yes (active HIGH)
Protection Over-current, short-circuit, thermal shutdown
Package SOT-25 (SC-74A, SOT-753)
Operating Temperature -40C to +85C
Output Capacitor 1 uF ceramic (min)
Start-up Time 200 us (typical)

Features

  • Ultra-low 35 uA quiescent current
  • 65 dB PSRR at 1 kHz for noise-sensitive applications
  • 200 us fast start-up time
  • Stable with 1 uF ceramic output capacitor
  • Current limit at approximately 1.4 A
  • Short-circuit protection clamps to 240 mA
  • Thermal shutdown at 145C with 130C hysteresis
  • Green molding compound, RoHS compliant

Applications

  • Notebook and server power rails
  • FPGA and DSP I/O power
  • Battery-powered portable devices
  • Consumer electronics 3.3V regulation
Product Introduction: AP7365-33WG-7 Product Introduction

The AP7365-33WG-7 from Diodes Incorporated is a 600 mA low-dropout linear regulator providing a fixed 3.3 V output with only 35 uA typical quiescent current. The device features 65 dB PSRR at 1 kHz, effectively rejecting input ripple from switching pre-regulators. The 300 mV typical dropout voltage at full load allows operation from a 3.6 V Li-ion battery down to end-of-discharge. An enable pin allows logic-controlled on/off switching for power sequencing. Internal protection includes current limiting (1.4 A typical), short-circuit protection (240 mA clamp), and thermal shutdown (145C with 15C hysteresis). The fast 200 us start-up time enables rapid power cycling for battery conservation. Stability is maintained with just a 1 uF ceramic output capacitor, minimizing BOM cost and PCB area.

Working Principle: AP7365-33WG-7 Working Principle

The AP7365-33WG-7 uses a P-channel MOSFET pass element in a common-source configuration. The error amplifier compares a fraction of the output voltage with an internal 0.8 V bandgap reference (in the adjustable version) or an internal resistor divider (in the fixed 3.3 V version). The amplifier drives the P-MOSFET gate to maintain regulation. The low 35 uA quiescent current is achieved by biasing the error amplifier and reference at minimal current while maintaining adequate gain-bandwidth for stability. The enable pin controls an internal switch that disconnects the bias circuitry when LOW, reducing supply current to sub-microamp levels. The 65 dB PSRR at 1 kHz is achieved through high loop gain at audio frequencies. Current limiting uses a sense resistor in the pass element path; when the voltage drop exceeds the threshold, the error amplifier limits gate drive. Thermal shutdown uses a temperature sensor near the pass transistor that disables the output when junction temperature exceeds 145C.

Pin Description: AP7365-33WG-7 Pin Definition and Functions
Pin Name Type Function
1 VIN Input Unregulated input (2.0-6.0V)
2 GND Ground Ground
3 EN Input Enable (HIGH=on, LOW=off)
4 NC – No connect
5 VOUT Output Regulated 3.3V output
Application Scenarios: In which products and applications is AP7365-33WG-7 used
  • 3.3V MCU I/O rail from 5V USB supply with 65dB ripple rejection
  • Portable medical device 3.3V rail from Li-ion battery with 35uA Iq
  • WiFi module 3.3V power with enable control for sleep mode
  • FPGA configuration rail requiring fast 200us power-up sequencing
Alternative Models: What chips are recommended as replacements for AP7365-33WG-7
Manufacturer Part Number Package Notes
Diodes Inc AP7365-18WG-7 SOT-25 1.8V fixed version
TI TLV70033DDCR SOT-23-5 300mA, 35uA Iq, similar
onsemi NCP511SN33T1G SOT-23-5 3.3V, 80mA, very low Iq
Richtek RT9193-33GB SOT-23-5 3.3V, 300mA, similar
Microchip MIC5219-3.3YM5 SOT-23-5 3.3V, 500mA, similar class

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1