Opens in a new tab

BTS5120-2EKA

AEC-qualified dual 120mΩ smart high-side switch, 2.5A/ch, kILIS=550, PROFET+ 12V, DSO-14-40 EP

0

Effective Inventory

Image for reference only

Manufacturer Part:

BTS5120-2EKA

Package:

PG-DSO-14-40 EP (8.65 x 3.9 x 1.47 mm, exposed pad)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The BTS5120-2EKA is an Infineon PROFET™+ 12V dual-channel smart high-side power switch in a PG-DSO-14-40 EP (exposed pad) package. Each channel features 120mΩ typical on-resistance, 2.5A nominal load current (2A with both channels), proportional load current sensing (kILIS=550), and comprehensive protection. AEC qualified and built on Smart6 technology, designed for automotive lamp driving up to 1x10W and LEDs.

Key Specifications

Channels 2 (dual high-side switch)
On-Resistance (RDS(on)) Typ 120mΩ @ 25°C; 240mΩ max @ 150°C
Nominal Load Current (1 ch active) 2.5A @ TA=85°C
Nominal Load Current (2 ch active) 2A @ TA=85°C
Operating Voltage Range 5V to 28V
Maximum Supply Voltage 41V
Current Sense Ratio (kILIS) 550 (typical)
Minimum Current Limitation 9A (short circuit)
Standby Current (IS(OFF)) 500nA max @ 25°C
Operating Temperature -40°C to +150°C
Qualification AEC qualified

Features

  • PROFET™+ 12V family member, Smart6 technology
  • Dual-channel high-side switch with 120mΩ typ. on-resistance
  • Proportional load current sense output (kILIS=550)
  • Open load detection in ON and OFF state
  • Short circuit to ground and battery detection
  • Over-temperature protection with restart
  • Over-current protection with intelligent restart
  • Overvoltage protection with external components
  • Undervoltage shutdown
  • Reverse polarity protection with external components
  • 3.3V and 5V compatible logic inputs
  • Diagnostic enable (DEN) and channel select (DSEL)
  • Stable diagnostic signal during short circuit
  • Enhanced kILIS dependency with temperature and load current

Applications

  • Automotive lamp drivers (up to 1 x 10W + LEDs)
  • Body electronics power distribution
  • Solenoid and valve drivers
  • Relay and fuse replacement
  • Automotive HVAC and seat heaters
Product Introduction: BTS5120-2EKA Product Introduction

The BTS5120-2EKA is an Infineon PROFET™+ 12V dual-channel smart high-side power switch in a PG-DSO-14-40 EP package. Each channel features 120mΩ typical on-resistance, 2.5A nominal load current at 85°C, and proportional current sensing with kILIS=550. Built on Smart6 technology, it provides over-temperature protection with controlled restart, over-current protection with intelligent restart, open/short load detection with stable diagnostic signal during short circuit, undervoltage shutdown, and reverse polarity protection. AEC qualified for automotive lamp driving (up to 1x10W bulbs and LEDs), solenoid control, and body electronics.

Working Principle: BTS5120-2EKA Working Principle

The BTS5120-2EKA operates as a dual-channel smart high-side power switch. Each channel contains a power DMOS transistor, charge pump, and protection/diagnostic circuitry. The INx pins control channel on/off. The charge pump generates a gate voltage above the supply rail to drive the N-channel DMOS. The IS pin provides a proportional current sense output: the sense current equals the load current divided by kILIS (550), allowing MCU current monitoring. The DEN and DSEL pins control diagnostic output. Over-temperature protection activates at 170°C typ. with 20°C hysteresis for controlled restart. Over-current protection trips at 9A min (12A typ.) with intelligent restart that limits RMS current during persistent faults to 2A. The enhanced kILIS dependency feature provides more accurate current sensing across temperature and load current ranges. The voltage-dependent current limitation reduces fault current at higher supply voltages for enhanced safety.

Pin Description: BTS5120-2EKA Pin Definition and Functions
Pin Mnemonic Description
1 GND Ground
2 IN0 Input channel 0 (active high)
3 DEN Diagnostic enable (active high)
4 IS Current sense output (analog)
5 DSEL Diagnosis channel select
6 IN1 Input channel 1 (active high)
7 N.C. Not connected
8-10 OUT0 Output channel 0
11 N.C. Not connected
12-14 OUT1 Output channel 1
EP VS Exposed pad (battery supply)
Application Scenarios: In which products and applications is BTS5120-2EKA used
  • Automotive 10W lamp driver with dual-channel switching and proportional current monitoring
  • Body control module power distribution with 120mΩ and enhanced kILIS accuracy
  • Solenoid and valve driver with over-current protection at 9A min and stable short-circuit diagnostics
  • Automotive seat heater switch with 2.5A per channel and intelligent restart control
  • Relay replacement with voltage-dependent current limitation for enhanced safety margin
Alternative Models: What chips are recommended as replacements for BTS5120-2EKA
Model Manufacturer Key Difference
BTS5180-2EKA Infineon 180mΩ, 2A, same family lower power
BTS5020-2EKA Infineon 33mΩ, 7A, higher power
BTS70402EPAXUMA1 Infineon PROFET+2, 19mΩ, ISO 26262
TPS1H200AQPWPRQ1 TI Single ch, 200mΩ, SPI
NCV8406 onsemi Single ch, 200mΩ, self-limiting

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1