Opens in a new tab

Home » Integrated Circuits ICs, Sensors » INA219BIDCNR

INA219BIDCNR

Zero-drift bidirectional current/power monitor with I2C, 0-26V common-mode, +/-0.1% accuracy, 12/16-bit ADC in VSSOP-8

4859

Effective Inventory

Image for reference only

Manufacturer Part:

INA219BIDCNR

Package:

VSSOP-8 (3.00 x 3.00 mm)

Brand:

Product Categories:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The INA219BIDCNR from Texas Instruments is a zero-drift, bidirectional current/power monitor with an I2C interface in a compact VSSOP-8 (3x3mm) package. It measures shunt voltage, bus voltage, current, and power with 12-bit resolution (configurable to 16-bit) across a 0V to 26V common-mode range, achieving plus or minus 0.1% gain accuracy.

Key Specifications

Common-Mode Voltage Range 0V ~ 26V
Resolution 12-bit (configurable 16-bit)
Measurement Parameters Shunt voltage, bus voltage, current, power
Interface I2C (16 address options)
Supply Voltage 3.0V ~ 5.5V
Gain Accuracy +/-0.1%
Quiescent Current 1mA (Typical)
Shutdown Current 6.5uA (Typical)
Package VSSOP-8 (3.00 x 3.00mm)
Operating Temperature -40°C ~ +125°C

Features

  • Zero-drift architecture for ultra-stable measurements over time and temperature
  • Bidirectional current measurement capability
  • Programmable calibration register for flexible shunt resistor values
  • 16 programmable I2C addresses for multi-device bus configurations
  • Configurable ADC resolution and conversion time
  • Power calculation performed internally
  • Built-in alert function with programmable over-limit threshold

Applications

  • Battery charging and discharging monitoring
  • Power supply load monitoring
  • Solar panel output measurement
  • Motor drive current sensing
  • Server rack power monitoring
Product Introduction: INA219BIDCNR Product Introduction

The INA219B is a high-side, bidirectional current shunt and power monitor from Texas Instruments with an I2C interface. It features a zero-drift architecture that provides excellent measurement stability over time and temperature. The device can sense drops across shunt resistors at common-mode voltages from 0V to 26V, independent of the supply voltage. The INA219B reports current, bus voltage, shunt voltage, and power. A programmable calibration register, combined with an internal multiplier, directly computes current in amperes and power in watts. The high-accuracy 12-bit ADC can be reconfigured to 16-bit oversampling for improved resolution. Sixteen programmable I2C addresses allow multiple devices on a single bus.

Working Principle: INA219BIDCNR Working Principle

The INA219B operates through three key subsystems: (1) A precision differential amplifier measures the voltage across an external shunt resistor with zero-drift architecture that auto-calibrates offset periodically. The amplified shunt voltage is digitized by the ADC. (2) A separate ADC channel measures the bus voltage at the IN- pin relative to ground, with an input range of 0V to 26V. (3) A digital computation engine applies the calibration value stored in the Calibration register to the digitized shunt voltage to compute the actual current value. The power value is then computed by multiplying the current and bus voltage values internally, relieving the host processor of this calculation. All results are stored in separate readable registers accessible via the I2C interface.

Pin Description: INA219BIDCNR Pin Definition and Functions
Pin Name Function
1 IN+ Positive shunt voltage input (load side)
2 IN- Negative shunt voltage input (bus side)
3 GND Ground
4 SDA I2C data (open-drain)
5 SCL I2C clock (open-drain)
6 A0 I2C address select bit 0
7 A1 I2C address select bit 1
8 VS Supply voltage (3.0V-5.5V)
Application Scenarios: In which products and applications is INA219BIDCNR used
  • Battery Management System: Monitors charge/discharge current and battery voltage with +/-0.1% accuracy for state-of-charge estimation
  • Server Rack Power Metering: 16 I2C addresses enable monitoring of multiple power rails on a single bus
  • Solar Panel MPPT Controller: Measures panel output current and voltage with zero-drift stability for maximum power point tracking
  • Motor Drive Protection: Bidirectional current sensing detects stall and overload conditions with programmable alert threshold
Alternative Models: What chips are recommended as replacements for INA219BIDCNR
Model Manufacturer Key Difference
INA226 TI 36V common-mode, 16-bit, alert pin
INA260 TI 36V, 16-bit, integrated 2mOhm shunt
PAC1710-1-AIA Microchip 0-32V, 11-bit, power monitor
MAX34417 ADI 12-channel power accumulator
LTC2945 ADI 0-80V, 12-bit, I2C power monitor

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1