Opens in a new tab

KS24C04

4Kbit I2C EEPROM, 512×8, 400kHz, 1M cycles, SOIC-8, write protect, non-volatile

6271

Effective Inventory

Image for reference only

Manufacturer Part:

KS24C04

Package:

SOIC-8 (4.90 x 3.90 x 1.37 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The KS24C04 from Samsung is a 4Kbit (512×8) I2C serial EEPROM in a SOIC-8 package. With 1 million erase/write cycles and 100-year data retention, it provides reliable non-volatile storage for configuration data, calibration, and user settings.

Key Specifications

Memory Size 4 Kbit (512 x 8 bit)
Interface I2C (2-wire serial)
Clock Frequency 400 kHz (max)
Write Cycle Time 5 ms (max, byte/page)
Endurance 1,000,000 cycles
Data Retention 100 years
Operating Temperature -40C to +85C

Features

  • 4Kbit (512 bytes) non-volatile EEPROM storage
  • I2C bus interface at up to 400kHz (fast mode)
  • 16-byte page write mode for efficient data storage
  • 1 million erase/write cycle endurance
  • 100-year data retention for long-term reliability
  • Hardware write protect pin for accidental write prevention

Applications

  • Device configuration and calibration storage
  • User preference and setting retention in consumer electronics
  • Industrial parameter storage in control systems
  • Asset tracking and identification data storage
Product Introduction: KS24C04 Product Introduction

The KS24C04 from Samsung is a 4Kbit (512 x 8 bit) electrically erasable programmable read-only memory (EEPROM) with I2C serial interface in a SOIC-8 package. The device uses a standard 2-wire I2C bus for communication, supporting clock frequencies up to 400kHz (fast mode). The memory is organized as 512 bytes of 8 bits each, with a 16-byte page write capability that allows up to 16 bytes to be written in a single write cycle. The write cycle time is 5ms maximum for both byte and page writes. The device supports 1 million erase/write cycles with 100-year data retention, providing long-term reliability for configuration and calibration data. A hardware write protect (WP) pin prevents accidental write operations when tied to VCC. The I2C device address is partially configurable through the A0-A2 address pins, allowing up to 8 devices on the same I2C bus. The device operates from 1.8V to 5.5V supply and is rated for -40C to +85C.

Working Principle: KS24C04 Working Principle

The KS24C04 uses floating-gate NMOS memory cells for non-volatile storage. (1) Memory Cell: Each bit is stored as charge on a floating gate electrode isolated by oxide layers. A charged floating gate shifts the transistor threshold voltage high (logic 0), while an uncharged gate leaves the transistor in the low-threshold state (logic 1). (2) Read: During a read operation, the memory cell transistor is biased at a voltage between the two threshold levels. If the cell is programmed (charged gate), the transistor does not conduct. If the cell is erased (uncharged gate), the transistor conducts. A sense amplifier detects the current difference and outputs the corresponding logic level. (3) Write: Programming uses Fowler-Nordheim tunneling – a high voltage (approximately 15V) applied across the thin oxide causes electrons to tunnel onto the floating gate. Erasing reverses the voltage to remove electrons. (4) I2C Protocol: The host initiates communication with a start condition, followed by the 7-bit device address and R/W bit. The addressed KS24C04 acknowledges and then receives or transmits data according to the R/W bit. (5) Page Write: Up to 16 bytes can be written sequentially. The lower 4 address bits auto-increment, while the upper bits remain constant. The write operation begins after the stop condition.

Pin Description: KS24C04 Pin Definition and Functions
Pin Name Type Function
1 A0 Input Address input 0
2 A1 Input Address input 1
3 A2 Input Address input 2
4 VSS Ground Ground
5 SDA I/O Serial data (open-drain, bidirectional)
6 SCL Input Serial clock
7 WP Input Write protect (HIGH = protect upper quadrant)
8 VCC Power Supply (1.8V to 5.5V)
Application Scenarios: In which products and applications is KS24C04 used
  • Device configuration and calibration storage with 100-year retention
  • User preference and setting retention in consumer electronics
  • Industrial parameter storage in control systems with 1M write cycles
  • Asset tracking and identification data storage with I2C interface
Alternative Models: What chips are recommended as replacements for KS24C04
Manufacturer Part Number Package Notes
Microchip AT24C04C-SSHL-T SOIC-8 Direct equivalent, popular
ST M24C04-WMN6TP SOIC-8 Direct equivalent
onsemi CAT24C04WI-GT3 SOIC-8 Direct equivalent
Microchip AT24C08B-SSHL-T SOIC-8 8Kbit version, same family

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1