Opens in a new tab

LM1117MP-3.3

800mA LDO, 3.3V fixed, 1.2V Vdo, ±1% accuracy, SOT-223

25768

Effective Inventory

Image for reference only

Manufacturer Part:

LM1117MP-3.3

Package:

SOT-223 (TO-261-4, 6.5 x 3.5 x 1.8mm, surface mount with thermal tab)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM1117MP-3.3 is an 800mA low-dropout positive linear regulator from Texas Instruments with fixed 3.3V output, 1.2V dropout at full load, and ±1% output accuracy in a SOT-223 surface-mount package.

Key Specifications

Output Voltage 3.3V fixed (±1% accuracy)
Output Current 800mA max
Input Voltage Range 4.5V to 15V
Dropout Voltage 1.2V max @ 800mA load
Line Regulation 0.2% max
Load Regulation 0.4% max
Quiescent Current 5mA typical
PSRR 75dB @ 120Hz
Output Capacitor 10µF minimum (tantalum or low-ESR ceramic)
Protection Over-current and thermal shutdown
Operating Temperature 0°C to +125°C
Package SOT-223 (6.5 x 3.5mm, surface mount)

Features

  • Fixed 3.3V output with ±1% accuracy
  • 800mA output current
  • 1.2V dropout at full load
  • 75dB ripple rejection at 120Hz
  • Over-current and thermal shutdown protection
  • Zener-trimmed bandgap reference for precision
  • Compatible with LM317 pinout (SOT-223 version)
  • Space-saving SOT-223 package with thermal tab

Applications

  • 5V to 3.3V logic level conversion
  • Post-regulator for switching power supplies
  • SCSI-2 active termination (2.85V version)
  • Battery-powered instrumentation
  • Embedded system 3.3V power rails
Product Introduction: LM1117MP-3.3 Product Introduction

The LM1117MP-3.3 from Texas Instruments is an 800mA low-dropout positive linear regulator providing a fixed 3.3V output with ±1% initial accuracy. The device uses a PNP pass transistor to achieve 1.2V maximum dropout voltage at 800mA load, enabling regulation from a 5V supply with 0.5V headroom. The 75dB ripple rejection at 120Hz makes it effective as a post-regulator following a switching supply, cleaning up residual switching ripple. Over-current protection limits the output current to prevent damage during fault conditions, and thermal shutdown disables the output if the junction temperature exceeds approximately 165°C. The SOT-223 package features a large thermal tab (connected to VOUT) that provides a low thermal resistance path to the PCB copper, enabling effective heat dissipation. The MP suffix denotes the SOT-223 package with tape-and-reel packaging. The -3.3 suffix specifies the 3.3V fixed output voltage.

Working Principle: LM1117MP-3.3 Working Principle

The LM1117MP-3.3 uses a PNP pass transistor between VIN and VOUT, controlled by an error amplifier that compares the output voltage against a zener-trimmed bandgap reference. When VOUT drops below 3.3V, the error amplifier drives the PNP base harder, increasing collector current (output current) flowing to the load. When VOUT rises above 3.3V, the error amplifier reduces base drive, limiting output current. The PNP pass transistor is key to the LDO operation: unlike NPN regulators where VOUT = VIN – VBE – VCESAT (minimum dropout ≈ 1.5V), the PNP configuration allows VOUT to approach VIN much more closely, limited only by VCE(sat) of the PNP. At 800mA, the worst-case dropout is 1.2V, meaning VIN must be at least 4.5V to maintain regulation. The 5mA quiescent current is the PNP base drive current that flows to ground rather than to the load; this increases with load current because higher load requires more base drive. The output capacitor (minimum 10µF) provides frequency compensation for the feedback loop; without it, the regulator may oscillate. The capacitor’s ESR must be between 0.3Ω and 22Ω for stability—modern low-ESR ceramics may require a small series resistor to maintain stability.

Pin Description: LM1117MP-3.3 Pin Definition and Functions
Pin Name Type Description
1 GND/ADJ Ground Ground (fixed version) or Adjust (adj. version)
2 VOUT Output Regulated 3.3V output (tab also VOUT)
3 VIN Input Input supply (4.5V to 15V)
4 TAB Output Thermal tab (connected to VOUT, for heat dissipation)

LM1117MP-3.3 uses the SOT-223-4 (MP) surface-mount package with Pin 1 = GND/Adjust, Pin 2 = VOUT (tab), Pin 3 = VIN, Pin 4 = Tab (connected to VOUT). The tab underneath the package must be soldered to a PCB copper pour for both electrical connection to VOUT and thermal dissipation. The MP package designation indicates SOT-223 from TI/National. Output current up to 800mA with 1.1V dropout at full load. A minimum 10µF tantalum output capacitor is required for stability. For fixed 3.3V output, the ADJ pin (Pin 1) is internally connected to a resistive divider — do not connect external components to Pin 1 on the fixed-voltage version.

Application Scenarios: In which products and applications is LM1117MP-3.3 used
  • 5V to 3.3V: VIN=5V, VOUT=3.3V, 1.7V headroom; at 500mA load, Pdiss = (5-3.3)×0.5 = 850mW — needs PCB copper heat area
  • Post-SMPS: 75dB PSRR attenuates 100mV switcher ripple to 18µV; adds clean analog-grade 3.3V
  • 3.3V MCU Rail: 800mA supports MCU + peripherals; thermal tab solders to copper pour for heat dissipation
  • Battery to Logic: 4.2V Li-ion to 3.3V; 0.9V dropout works until battery discharges to ~4.5V
  • Multi-Rail System: LM1117-3.3 + LM1117-5.0 from 12V bus; thermal management critical at high VI-VO
Alternative Models: What chips are recommended as replacements for LM1117MP-3.3
Model Manufacturer Key Difference Package Specs
TLV1117LV33DCYR TI Modern 1A LDO with 300mV dropout and 500µA IQ, stable with ceramic capacitors only SOT-223-3 3.3V/1A/300mV
AMS1117-3.3 Advanced Budget equivalent with 1.1V dropout at 1A, widely available and very low cost SOT-223-3 3.3V/1A/1.1V
MCP1826T-3302E/DC Microchip 1A anyCAP LDO with 210mV dropout, stable with any capacitor type and value SOT-223-3 3.3V/1A/210mV
LD1117DT33CTR ST 800mA LDO with 1V dropout in DPAK for surface-mount 3.3V supply rails DPAK-3 3.3V/800mA
AZ1117IH-3.3TRG1 Diodes Inc 1A LDO with 1.1V dropout, ESD protection, and pin-compatible with AMS1117-3.3 SOT-223-3 3.3V/1A/1.1V

LM1117MP-3.3 is an 800mA low-dropout regulator in SOT-223-4 with 1.1V dropout at 800mA and 3.3V fixed output. The TLV1117LV33DCYR is the modern TI replacement with lower 300mV dropout and ceramic capacitor stability. The AMS1117-3.3 is the most popular budget alternative with identical SOT-223-3 pinout. For anyCAP stability, MCP1826T guarantees stability with any capacitor type.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1