Opens in a new tab

LM2576S-5.0

3A step-down switching regulator, 5.0V fixed, TO-263-5

4534

Effective Inventory

Image for reference only

Manufacturer Part:

LM2576S-5.0

Package:

TO-263-5 (10.0 x 8.7 x 4.6 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

LM2576S-5.0 Overview

The LM2576S-5.0 is a fixed 5.0V output step-down DC-DC converter from Texas Instruments, with maximum input voltage of 40V, output current of 3A, in a TO-263-5 package. It integrates frequency compensation, requiring only a few external components.

Key Features

  • Input voltage range: 4.5V-40V
  • Fixed output voltage: 5.0V
  • Maximum output current: 3A
  • Switching frequency: 52kHz
  • Standby current: 50uA
  • Efficiency up to 88%
Product Introduction: LM2576S-5.0 Product Introduction

The LM2576S-5.0 is a 3 A, 40 V step-down switching voltage regulator from Texas Instruments in a TO-263-5 (D2PAK) surface-mount package, providing a fixed 5.0 V output. It requires only four external components (input capacitor, output capacitor, catch diode, and inductor) and operates at a fixed 52 kHz switching frequency. Features include 77 percent efficiency, TTL-level shutdown with 50 uA standby current, cycle-by-cycle current limiting, and thermal shutdown with full protection under fault conditions. The output voltage tolerance is plus or minus 4 percent over line and load conditions.

Working Principle: LM2576S-5.0 Working Principle

The LM2576S-5.0 uses a fixed-frequency pulse-width modulation (PWM) buck converter topology operating at 52 kHz. The internal power switch (a Darlington NPN transistor) connects the input voltage to the output inductor during the on-time, causing inductor current to ramp up linearly. When the switch turns off, the inductor current freewheels through the external catch diode (a Schottky diode is recommended for efficiency), delivering energy to the output capacitor and load. The output voltage is divided down by an internal resistor network and compared with an internal 1.23 V reference by the error amplifier. The error amplifier output controls the PWM comparator, which adjusts the switch duty cycle to maintain the output at 5.0 V. The cycle-by-cycle current limit monitors the switch current and terminates the on-time if it exceeds approximately 4.5 A, protecting the device from overload. The ON/OFF pin allows TTL-level shutdown; when pulled below 1.4 V, the device enters a low-power standby mode drawing only 50 uA typical. The thermal shutdown disables the output switch when the die temperature exceeds approximately 170 C.

Pin Description: LM2576S-5.0 Pin Definition and Functions
Pin Name Description
1 VIN Input supply (4 V to 40 V); connect 100 uF electrolytic capacitor to GND
2 OUTPUT Switch output; connect to inductor and catch diode cathode
3 GND Ground; connect to PCB ground plane for thermal management
4 FEEDBACK Output voltage feedback; connect directly to output for fixed 5.0 V version
5 ON/OFF Shutdown control; pull below 1.4 V to disable, leave open or pull above 2.4 V for normal operation
Tab GND Thermal tab; solder to PCB copper pour for heat dissipation
Application Scenarios: In which products and applications is LM2576S-5.0 used
  • Automotive 12 V to 5 V: Converting vehicle battery voltage to 5 V logic supply for microcontrollers and peripherals
  • Industrial Power Supplies: Efficient 24 V to 5 V step-down for PLC I/O modules and sensor interfaces
  • Battery-Powered Devices: Stepping down multi-cell battery packs to 5 V with minimal heat generation
  • Embedded Systems: Main 5 V rail generation from unregulated 8 V to 30 V DC input
  • Telecom Power: 48 V nominal to 5 V conversion in communication equipment using the HV version
Alternative Models: What chips are recommended as replacements for LM2576S-5.0
Model Manufacturer Iout Vin Frequency Package
LM2576HV-5.0 Texas Instruments 3 A 4-60 V 52 kHz TO-263
LM2596S-5.0 Texas Instruments 3 A 4-40 V 150 kHz TO-263
LMR33630 Texas Instruments 3 A 3.8-36 V 400 kHz QFN/HTSSOP
AP1509-5.0 BCD Semiconductor 2 A 4.5-40 V 150 kHz SOIC-8
XL1509-5.0 XLSEMI 2 A 4.5-40 V 60 kHz SOP-8

LM2576S-5.0 is a 3A/40V step-down regulator from TI in TO-263 (D2PAK). The LM2576SX-5.0/NOPB is the active replacement in the same package. The LM2596S-5.0 provides 3A with 150kHz switching for smaller inductors. The LMR51430 from TI offers modern 500kHz/1.1MHz switching in smaller VQFN. The TLVM13630 from TI is a 3A power module requiring no external inductor selection. The AP1509-5.0 from BCR provides a lower-cost 2A/150kHz alternative. The LM2676S-5.0 offers 260kHz switching for smaller passive components.

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1