Opens in a new tab

LM324N

Quad general-purpose op-amp, 1MHz, 3-32V single supply, GND-referenced, PDIP-14

15000

Effective Inventory

Image for reference only

Manufacturer Part:

LM324N

Package:

PDIP-14 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM324N from Texas Instruments is the industry-standard quad general-purpose operational amplifier with single-supply operation (3V-32V), input common-mode range including ground, and 1MHz gain-bandwidth product — four op-amps in a single 14-pin PDIP package.

Key Specifications

Number of Channels 4 (quad, independent)
Supply Voltage Range 3V to 32V (single) or ±1.5V to ±16V (dual)
Gain-Bandwidth Product 1MHz (1.2MHz typical)
Slew Rate 0.5V/µs typical
Open-Loop Voltage Gain 100dB typical (100V/mV)
Input Offset Voltage 2mV typical, 7mV max
Input Bias Current 45nA typical, 250nA max
Input Offset Current 5nA typical, 50nA max
Input Common-Mode Range 0V to V+−1.5V (includes GND)
Output Voltage Swing 0V to V+−1.5V (single supply)
Output Current 20mA typical (source/sink)
Supply Current (all 4 amps) 700µA typical (independent of supply)
CMRR 85dB typical
Operating Temperature 0°C to +70°C
Package PDIP-14 (19.3 x 6.35mm)

Features

  • Four internally compensated op-amps in one package
  • Single-supply operation: 3V to 32V
  • Input common-mode range includes ground (GND)
  • Output swings to GND (no negative supply needed)
  • 700µA total supply current — battery friendly
  • Internally frequency compensated for unity gain

Applications

  • Single-supply signal conditioning
  • Transducer amplifier interfaces
  • DC gain blocks
  • Active filters
  • Comparators
  • Oscillators
Product Introduction: LM324N Product Introduction

The LM324N from Texas Instruments is the most widely used quad operational amplifier, containing four independent high-gain internally frequency-compensated op-amps in a single 14-pin DIP package. Its defining advantage over the LM741 and LM358 is the combination of four channels AND single-supply operation. The input common-mode voltage range includes ground (0V), meaning the non-inverting input can be connected directly to GND without a negative supply — critical for single-supply designs where the signal is referenced to ground. The output can also swing to within a few millivolts of ground (when sinking current), and up to V+−1.5V when sourcing. The 1MHz GBW and 0.5V/µs slew rate limit it to low-frequency applications (full-power bandwidth ≈ 8kHz at ±10V output). The total supply current of only 700µA for all four amplifiers makes it suitable for battery operation. At $0.316/1ku, the LM324 is the most cost-effective way to get four op-amps. The N suffix denotes the PDIP-14 through-hole package.

Working Principle: LM324N Working Principle

Each of the four op-amps in the LM324N is a voltage-feedback amplifier with internal compensation. The PNP input stage allows the common-mode range to include ground (the PNP emitters are biased at ~0.6V above the inputs, so the inputs can go to 0V). The class AB output stage can both source and sink current, with the output swinging to within ~5mV of ground when sinking small currents and to V+−1.5V when sourcing. In single-supply operation, the signal must remain within 0V to V+−1.5V at both input and output. For AC-coupled applications, a bias voltage (typically V+/2) establishes the operating point. For DC applications with ground-referenced signals (like sensor outputs that vary from 0V upward), no bias is needed — the input can go to 0V and the output can swing to near 0V. The internal 30pF compensation capacitor creates a dominant pole at ~10Hz, rolling off the gain at 20dB/decade to cross unity gain at 1MHz. Closed-loop bandwidth = GBW/noise_gain; at gain=100, BW ≈ 10kHz. The 700µA total quiescent current is essentially independent of supply voltage (3V to 32V), thanks to a constant-current bias network.

Pin Description: LM324N Pin Definition and Functions
Pin Name Type Description
1 1OUT Output Op-amp 1 output
2 1IN− Input Op-amp 1 inverting input
3 1IN+ Input Op-amp 1 non-inverting input
4 VCC Power Positive supply (3V to 32V)
5 2IN+ Input Op-amp 2 non-inverting input
6 2IN− Input Op-amp 2 inverting input
7 2OUT Output Op-amp 2 output
8 3OUT Output Op-amp 3 output
9 3IN− Input Op-amp 3 inverting input
10 3IN+ Input Op-amp 3 non-inverting input
11 GND / V− Power Ground or negative supply
12 4IN+ Input Op-amp 4 non-inverting input
13 4IN− Input Op-amp 4 inverting input
14 4OUT Output Op-amp 4 output
Application Scenarios: In which products and applications is LM324N used
  • Single-Supply Non-Inverting Amp: Sensor (0-1V) → 1IN+; Rf/Rg = 4; 1OUT = 0-5V; VCC = 5V single supply; GND = pin 11
  • Comparator: Sensor → 1IN+; threshold voltage → 1IN−; 1OUT drives LED; no feedback resistor; open-loop comparison
  • 4-Channel Signal Conditioner: 4 sensors → 4 op-amps; each configured for appropriate gain; single VCC supply; one IC handles all 4 channels
  • Active Filter: Sallen-Key low-pass: 2 resistors + 2 capacitors per op-amp; cutoff at desired frequency; remaining 2 op-amps for gain stages
  • AC-Coupled Amp: VCC=12V; two 10kΩ resistors create V+/2 = 6V bias at 1IN+; AC signal through coupling cap + Rin → 1IN−; Rf feedback; output centered at 6V
Alternative Models: What chips are recommended as replacements for LM324N
Model Manufacturer Key Difference Package Specs
LM324AN TI Improved version with lower 2mV max input offset voltage for precision measurement circuits DIP-14 1.1MHz/4-ch
LM324B TI Modern upgrade: 36V supply, 1.2MHz GBW, 3mV offset, rail-to-rail output swing capability DIP-14 1.2MHz/36V
LM358N TI Dual op-amp version (2 channels) in DIP-8 for simpler single/dual signal chain designs DIP-8 1.1MHz/2-ch
TL074CN TI Quad JFET-input op-amp with 65pA input bias current and 3MHz GBW for low-noise applications DIP-14 3MHz/JFET
LM2902N TI Automotive-grade -40 to +125C version for under-hood and industrial environments DIP-14 1.1MHz/-40-125C
MCP6004-I/P Microchip Low-voltage 1.8-6V quad R-R op-amp with 1MHz GBW for battery-powered instrumentation DIP-14 1MHz/1.8-6V

LM324N is the industry-standard quad general-purpose op-amp in DIP-14 with 1.1MHz GBW and 3-32V single-supply operation. All four channels share the same power rails. LM324B offers modern 36V rail-to-rail output. For JFET-input low-noise applications, TL074 provides 3MHz GBW and 65pA bias current. For low-voltage designs, MCP6004 operates down to 1.8V.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1