Opens in a new tab

LM741CN

General-purpose op-amp, 1MHz GBW, 0.5V/µs, ±22V, PDIP-8

12000

Effective Inventory

Image for reference only

Manufacturer Part:

LM741CN

Package:

PDIP-8 (9.81 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM741CN from Texas Instruments is the classic general-purpose operational amplifier with internal frequency compensation, 1MHz gain-bandwidth product, and ±22V supply range in an 8-pin PDIP package — the most widely taught and referenced op-amp in electronics.

Key Specifications

Type General-purpose operational amplifier
Supply Voltage Range ±5V to ±22V (dual supply)
Input Offset Voltage 2mV typical, 6mV max
Input Bias Current 80nA typical, 500nA max
Input Offset Current 20nA typical, 200nA max
Input Resistance 0.3MΩ minimum (2MΩ typical)
Open-Loop Voltage Gain 200V/mV typical (200,000 V/V)
Gain-Bandwidth Product 1MHz typical
Slew Rate 0.5V/µs typical
Output Voltage Swing ±12V typical @ RL=2kΩ, ±15V supply
Common-Mode Rejection Ratio 90dB typical
Supply Current 1.7mA typical, 2.8mA max
Operating Temperature 0°C to +70°C
Package PDIP-8 (9.81 x 6.35mm)

Features

  • Internal frequency compensation — no external capacitor needed
  • Short-circuit protection on output
  • Offset null adjustment via pins 1 and 5
  • Wide supply voltage range: ±5V to ±22V
  • No latch-up

Applications

  • Non-inverting and inverting amplifiers
  • Integrator and differentiator circuits
  • Voltage follower (buffer)
  • Summing amplifier
  • Active filters
  • Comparator (open-loop)
Product Introduction: LM741CN Product Introduction

The LM741CN from Texas Instruments is the most iconic general-purpose operational amplifier, originally designed by Fairchild Semiconductor in the late 1960s and still in production today. It features internal frequency compensation (a dominant pole at ~10Hz) that ensures unconditional stability in voltage-follower configuration without any external components — unlike earlier op-amps like the LM709 that required external compensation capacitors. The 1MHz gain-bandwidth product and 0.5V/µs slew rate limit it to low-frequency applications: the full-power bandwidth at ±10V output is only ~8kHz (BW = SR / (2π × Vpeak)). For audio and DC signal conditioning, the 741 remains perfectly adequate. The 2mV typical input offset voltage can be trimmed to zero using a 10kΩ potentiometer between pins 1 and 5 (offset null). The 80nA input bias current means that at 100kΩ source resistance, the offset from bias current alone is 8mV — significant for precision applications. The 741 requires a dual supply (±15V typical) and cannot swing its output closer than about 2-3V to either rail. The CN suffix denotes the commercial-temperature PDIP-8 package.

Working Principle: LM741CN Working Principle

The LM741CN is a voltage-feedback operational amplifier with three stages: (1) Differential input stage: two matched NPN transistors form a differential pair that converts the differential input voltage (V+ − V−) into a differential current. The input bias current (80nA typical) is the base current of these transistors. (2) Voltage gain stage: a common-emitter amplifier provides most of the open-loop gain (200,000 typical). An internal 30pF compensation capacitor creates a single dominant pole at ~10Hz, rolling off the gain at 20dB/decade. At 1MHz, the gain has dropped to 1 (0dB) — this is the gain-bandwidth product. (3) Output stage: a class-AB push-pull amplifier provides low output impedance and can drive loads down to 2kΩ. The output can source and sink ~25mA with short-circuit protection. The op-amp exploits negative feedback: when configured with a feedback network from output to inverting input, the high open-loop gain forces the differential input voltage to nearly zero (virtual short). For a non-inverting amplifier: Vout = (1 + Rf/Rg) × Vin. For an inverting amplifier: Vout = -(Rf/Rg) × Vin. The closed-loop bandwidth is GBW / noise_gain; at gain=10, BW = 100kHz.

Pin Description: LM741CN Pin Definition and Functions
Pin Name Type Description
1 Offset Null Adjust Offset null adjustment (connect to pot wiper)
2 V− (Inverting) Input Inverting input
3 V+ (Non-inverting) Input Non-inverting input
4 V− Power Negative supply (−15V typical)
5 Offset Null Adjust Offset null adjustment (connect to pot wiper)
6 Output Output Amplifier output
7 V+ Power Positive supply (+15V typical)
8 NC — No connect (internal compensation capacitor)

LM741CN uses the PDIP-8 package with classic 741 op-amp pinout: Pin 1 = Offset Null 1, Pin 2 = Inverting Input (-), Pin 3 = Non-inverting Input (+), Pin 4 = VEE (-V), Pin 5 = Offset Null 2, Pin 6 = Output, Pin 7 = VCC (+V), Pin 8 = NC. The offset null pins (1 and 5) allow external trimming of input offset voltage to zero using a 10kΩ potentiometer wiper to VEE. The 741 requires dual supplies (±5V to ±18V) and cannot operate single-supply — inputs cannot approach ground. For single-supply replacement, use LM358 (dual) or LM321 (single). The NC pin 8 must be left floating.

Application Scenarios: In which products and applications is LM741CN used
  • Non-Inverting Amp: Vin→pin 3; Rf from pin 6 to pin 2; Rg from pin 2 to GND; Gain = 1 + Rf/Rg; ±15V supply
  • Inverting Amp: Vin→Rin→pin 2; Rf from pin 6 to pin 2; pin 3 to GND; Gain = −Rf/Rin
  • Voltage Follower: Pin 6 connected directly to pin 2; Vin→pin 3; Gain = 1; high-Z input, low-Z output buffer
  • Summing Amp: Multiple inputs through resistors to pin 2; Rf feedback; Vout = −(Rf·V1/R1 + Rf·V2/R2 + …); inverting summing
  • Offset Trim: 10kΩ pot between pins 1 and 5; wiper to V− (pin 4); adjust for zero output with grounded inputs
Alternative Models: What chips are recommended as replacements for LM741CN
Model Manufacturer Key Difference Package Specs
LM358N TI Dual op-amp with single 3-32V supply operation and ground-referenced inputs for modern designs DIP-8 1.1MHz/2-ch
NE5532P TI Dual low-noise audio op-amp with 10MHz GBW for audio preamplifier and equalizer circuits DIP-8 10MHz/9V/µs
TL072CP TI Dual JFET-input op-amp with 3MHz GBW and 65pA bias current for low-drift applications DIP-8 3MHz/JFET
OP07CP TI Ultra-low offset 75µV precision op-amp for instrumentation and measurement bridge circuits DIP-8 600kHz/75µV
MCP6002-I/P Microchip Dual 1.8-6V rail-to-rail CMOS op-amp with 1MHz GBW for low-voltage modern systems DIP-8 1MHz/1.8-6V

LM741CN is the classic single general-purpose op-amp in DIP-8 with ±15V dual supply and 1MHz GBW. While historically dominant, modern alternatives like LM358 (single-supply), TL072 (JFET-input), and MCP6002 (1.8V R-R) offer significant improvements in power, speed, and supply range. For precision applications, OP07 provides 75µV offset voltage.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1