Opens in a new tab

LM7805CT

5V 1A positive linear regulator, TO-220, thermal/SCP protection

30000

Effective Inventory

Image for reference only

Manufacturer Part:

LM7805CT

Package:

TO-220-3 (15.6 x 10.6 x 4.6mm, through-hole, tab=GND)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM7805CT from onsemi/TI is a 3-terminal 1A positive voltage regulator providing a fixed 5V output with internal thermal shutdown and short-circuit protection in a TO-220 package — the most widely used 5V regulator in electronics.

Key Specifications

Output Voltage 5V fixed (±2% at 25°C for A-grade)
Output Current 1A continuous (1.5A peak)
Input Voltage Range 7.5V to 20V (7.5V min for regulation)
Maximum Input Voltage 35V
Dropout Voltage 2V typical @ 1A
Line Regulation 5mV typical (7.5V to 20V)
Load Regulation 10mV typical (5mA to 1A)
Quiescent Current 5mA typical
Ripple Rejection 68dB typical @ 120Hz
Thermal Shutdown ~170°C junction
Short-Circuit Current 2.1A typical
Operating Temperature -40°C to +125°C (junction)
Package TO-220-3 (through-hole, tab=GND)

Features

  • Fixed 5V output — the standard logic supply voltage
  • 1A continuous output current
  • Internal thermal overload protection
  • Internal short-circuit current limiting
  • Output transistor safe operating area protection
  • 68dB ripple rejection at 120Hz
  • Only two external capacitors needed

Applications

  • 5V logic power supply
  • Microcontroller voltage regulation
  • Post-regulator after switching supply
  • Bench power supply
  • USB 5V power source
Product Introduction: LM7805CT Product Introduction

The LM7805CT from onsemi/Texas Instruments is the most ubiquitous voltage regulator in electronics, providing a fixed 5V output at up to 1A from an input of 7.5V or higher. It is the backbone of virtually every 5V logic power supply, from Arduino boards to industrial controllers. The device requires only two external capacitors (0.33µF input, 0.1µF output) for stable operation. The 2V dropout voltage means the input must be at least 7V to maintain 5V output at full load. The 68dB ripple rejection effectively attenuates AC mains ripple by a factor of 2500, making the output clean enough for sensitive analog circuits. Internal protection includes thermal shutdown (disables output at ~170°C junction), current limiting (short-circuit current limited to ~2.1A), and safe operating area compensation. The CT suffix denotes the TO-220 package. For lower dropout alternatives, the LM2940 (0.5V dropout at 1A) is preferred when input voltage is close to 5V.

Working Principle: LM7805CT Working Principle

The LM7805CT uses a series pass transistor (NPN Darlington) between the input and output, controlled by a feedback loop that compares a fraction of the output voltage with an internal bandgap reference. When the output voltage drops below 5V, the error amplifier increases the drive to the pass transistor, increasing current flow. When the output rises above 5V, the drive is reduced. The thermal protection circuit monitors the junction temperature; at ~170°C, the pass transistor is disabled until the device cools. The current limiting circuit limits the pass transistor current to approximately 2.1A during a short circuit. The safe operating area (SOA) protection further reduces the current limit as the input-output voltage differential increases. The 5mA quiescent current flows through the ground pin and biases the internal reference and error amplifier. The 0.33µF input capacitor prevents oscillation when the source impedance is high, and the 0.1µF output capacitor improves transient response.

Pin Description: LM7805CT Pin Definition and Functions
Pin Name Type Description
1 INPUT Power Input Unregulated input voltage. Must be at least 3.0V (Vout + Vdropout ≈ 3.0V) for proper regulation. Maximum 35V. Bypass with 0.33µF ceramic capacitor to GND if supply is more than 6 inches from the regulator.
2 GND Ground Common ground reference. The TO-220 tab is electrically connected to this pin and serves as the primary heat dissipation path. Use thermal compound and heatsink for currents above 500mA.
3 OUTPUT Power Output Regulated 0.5V DC output at up to 1A continuous current with ±4% tolerance. Bypass with 0.1µF ceramic capacitor to GND to improve transient response and output impedance. Do not apply external voltage higher than 0.5V to prevent reverse bias damage.

Pin assignment follows standard TO-220-3 layout: Pin 1 (left) = Input, Pin 2 (center) = Ground/Tab, Pin 3 (right) = Output, when viewed from the front with pins pointing down. The metal tab on the back is electrically connected to Pin 2 (GND) and must be insulated from the heatsink when the heatsink is not at ground potential. Output capacitance of 0.1µF is required for stability; input capacitance of 0.33µF is recommended when the input supply is remote.

Application Scenarios: In which products and applications is LM7805CT used
  • 5V MCU Supply: 9V battery or wall adapter → LM7805CT → 5V for MCU, TTL logic, sensors; 0.33µF + 0.1µF caps
  • Arduino Power: 12V DC jack → LM7805CT → 5V rail; Pdiss = (12-5)×0.5A = 3.5W; small heatsink needed
  • Post-SMPS: 7.5V switching supply → LM7805CT → clean 5V; 68dB ripple rejection eliminates switcher noise
  • USB Power: 9V battery → LM7805CT → 5V USB output; charges phone or powers USB device
  • Split Supply: LM7805CT (+5V) + LM7905CT (-5V) from center-tapped transformer; ±5V for op-amp circuits
Alternative Models: What chips are recommended as replacements for LM7805CT
Model Manufacturer Key Difference Package Specs
LM7805ACT onsemi Tighter output tolerance: ±2% vs ±4% for precision power supply applications TO-220-3 0.5V/1A
L7805CV STMicroelectronics Direct equivalent with 1.5A output current, internal thermal shutdown and current limiting TO-220-3 0.5V/1.5A
MC7805CTG onsemi Current production replacement with identical electrical specifications and RoHS compliance TO-220-3 0.5V/1A
KA7805 onsemi/Fairchild Budget-friendly version with ±4% tolerance and standard 1A output current rating TO-220-3 0.5V/1A
MC7805ABD2TG onsemi Surface-mount DPAK version with ±2% A-grade tolerance for compact PCB layouts DPAK-3 0.5V/1A
LM2940CT-0.5 TI Low-dropout version with 0.5V max dropout at 1A for battery-powered and automotive systems TO-220-3 0.5V/1A LDO

LM7805CT is a 0.5V fixed positive voltage regulator in TO-220-3 with 1A output and ±4% tolerance. The ACT suffix offers ±2% precision. For surface-mount designs, use MC7805ABD2TG (DPAK). For battery-powered systems, the LM2940CT-0.5 LDO version reduces dropout to 0.5V. All 7805 variants are pin-compatible (IN-GND-OUT) and require only input/output capacitors.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1