Opens in a new tab

LM7812CT

12V 1A positive linear regulator, TO-220, thermal/short-circuit protection

21000

Effective Inventory

Image for reference only

Manufacturer Part:

LM7812CT

Package:

TO-220-3 (15.6 x 10.6 x 4.6mm, through-hole, tab=GND)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LM7812CT from onsemi is a 3-terminal 1A positive voltage regulator providing a fixed 12V output with internal thermal overload protection, short-circuit protection, and output transistor safe operating area compensation in a TO-220 package.

Key Specifications

Output Voltage 12V fixed (±2% at 25°C for A-grade)
Output Current 1A (up to 1.5A with heatsink)
Input Voltage Range 14.5V to 27V (14.5V min for regulation)
Maximum Input Voltage 35V
Dropout Voltage 2V typical @ 1A
Line Regulation 10mV typical (14.8V to 27V, IO=500mA)
Load Regulation 12mV typical (5mA to 1A)
Quiescent Current 6mA typical
Ripple Rejection 61dB typical @ 120Hz
Output Noise Voltage 75µV typical (10Hz to 100kHz)
Short-Circuit Current 1.5A typical
Peak Output Current 2.4A typical
Thermal Shutdown ~170°C junction
Operating Temperature -40°C to +125°C (junction)
Package TO-220-3 (through-hole, tab=GND)

Features

  • Fixed 12V output with ±2% tolerance
  • 1A continuous output current
  • Internal thermal overload protection
  • Internal short-circuit current limiting
  • Output transistor safe operating area protection
  • High ripple rejection: 61dB at 120Hz
  • Only two external capacitors needed

Applications

  • 12V power supply regulation
  • Analog circuit power rails
  • Relay and solenoid driver supply
  • Post-regulator after switching supply
  • Automotive 12V systems
Product Introduction: LM7812CT Product Introduction

The LM7812CT from onsemi (formerly Fairchild/National Semiconductor) is a 3-terminal positive voltage regulator providing a fixed 12V output at up to 1A load current. It is part of the ubiquitous 78xx series that has been the backbone of linear power supply design for decades. The device requires only two external capacitors (0.33µF input, 0.1µF output) for stable operation. Internal protection includes thermal shutdown (disables output at ~170°C junction), current limiting (short-circuit current limited to ~1.5A), and safe operating area compensation (reduces current limit as input-output differential increases). The 2V dropout voltage means the input must be at least 14V to maintain 12V output at full load. The 61dB ripple rejection at 120Hz makes it effective for cleaning up rectified AC or noisy switching supply outputs. The CT suffix denotes the TO-220 package with commercial/industrial temperature range. Note: DigiKey lists this part as obsolete; the MC7812CTG from onsemi is the current production equivalent.

Working Principle: LM7812CT Working Principle

The LM7812CT uses a series pass transistor (NPN Darlington) between the input and output, controlled by a feedback loop that compares a fraction of the output voltage with an internal bandgap reference. The error amplifier drives the pass transistor to maintain VOUT = 12V. When the output voltage drops below 12V (due to increased load or decreased input), the error amplifier increases the drive to the pass transistor, increasing current flow and raising the output voltage. When the output rises above 12V, the drive is reduced. The thermal protection circuit uses a temperature sensor on the die; when junction temperature exceeds approximately 170°C, the pass transistor is disabled until the device cools to a safe temperature. The current limiting circuit monitors the pass transistor current; when it exceeds approximately 1.5A at low input-output differential, the drive is limited to prevent damage. The safe operating area (SOA) protection further reduces the current limit as the input-output voltage differential increases, keeping the pass transistor within its safe operating region. The 6mA quiescent current flows through the ground pin and provides bias for the internal reference and error amplifier. The 0.33µF input capacitor prevents oscillation when the input source has high impedance, and the 0.1µF output capacitor improves transient response.

Pin Description: LM7812CT Pin Definition and Functions
Pin Name Type Description
1 INPUT Power Input Unregulated input voltage. Must be at least 3.7V (Vout + Vdropout ≈ 3.7V) for proper regulation. Maximum 35V. Bypass with 0.33µF ceramic capacitor to GND if supply is more than 6 inches from the regulator.
2 GND Ground Common ground reference. The TO-220 tab is electrically connected to this pin and serves as the primary heat dissipation path. Use thermal compound and heatsink for currents above 500mA.
3 OUTPUT Power Output Regulated 1.2V DC output at up to 1A continuous current with ±4% tolerance. Bypass with 0.1µF ceramic capacitor to GND to improve transient response and output impedance. Do not apply external voltage higher than 1.2V to prevent reverse bias damage.

Pin assignment follows standard TO-220-3 layout: Pin 1 (left) = Input, Pin 2 (center) = Ground/Tab, Pin 3 (right) = Output, when viewed from the front with pins pointing down. The metal tab on the back is electrically connected to Pin 2 (GND) and must be insulated from the heatsink when the heatsink is not at ground potential. Output capacitance of 0.1µF is required for stability; input capacitance of 0.33µF is recommended when the input supply is remote.

Application Scenarios: In which products and applications is LM7812CT used
  • 12V Bench Supply: 18V AC transformer → bridge rectifier → 2200µF filter → LM7812CT; 12V regulated output at up to 1A
  • Post-SMPS Regulator: 15V switching supply → LM7812CT; 61dB ripple rejection cleans switcher noise; Pdiss = (15-12)×1A = 3W
  • Automotive 12V: 14.4V car battery → LM7812CT; stable 12V for analog circuits despite battery voltage variation
  • Split Supply: LM7812CT (+12V) + LM7912CT (-12V) from center-tapped transformer; ±12V for op-amp circuits
  • Adjustable Output: LM7812CT with external op-amp and resistor divider to set output above 12V (e.g., 13.8V for battery charging)
Alternative Models: What chips are recommended as replacements for LM7812CT
Model Manufacturer Key Difference Package Specs
LM7812ACT onsemi Tighter output tolerance: ±2% vs ±4% for precision power supply applications TO-220-3 1.2V/1A
L7812CV STMicroelectronics Direct equivalent with 1.5A output current, internal thermal shutdown and current limiting TO-220-3 1.2V/1.5A
MC7812CTG onsemi Current production replacement with identical electrical specifications and RoHS compliance TO-220-3 1.2V/1A
KA7812 onsemi/Fairchild Budget-friendly version with ±4% tolerance and standard 1A output current rating TO-220-3 1.2V/1A
MC7812ABD2TG onsemi Surface-mount DPAK version with ±2% A-grade tolerance for compact PCB layouts DPAK-3 1.2V/1A
LM2940CT-1.2 TI Low-dropout version with 0.5V max dropout at 1A for battery-powered and automotive systems TO-220-3 1.2V/1A LDO

LM7812CT is a 1.2V fixed positive voltage regulator in TO-220-3 with 1A output and ±4% tolerance. The ACT suffix offers ±2% precision. For surface-mount designs, use MC7812ABD2TG (DPAK). For battery-powered systems, the LM2940CT-1.2 LDO version reduces dropout to 0.5V. All 7812 variants are pin-compatible (IN-GND-OUT) and require only input/output capacitors.

Recommend Parts

IRFS4310ZTRLPBF

IRFS4310ZTRLPBF – 100V N-Channel HEXFET Power MOSFET, 7 mΩ RDS(on), D2PAK (TO-263AB)

Brand: infineon

Package: D2PAK (TO-263AB)

IN STOCK: 11137pcs

Cargo cycle: 3-7 Days

The minimum order is 1

MSASJ105BB5475MFNA01

4.7uF 6.3V X5R MLCC, 0402, Taiyo Yuden

Brand: gigadevice

Package: 0402 (1005 Metric, 1.0 x 0.5 x 0.5 mm)

IN STOCK: 9701pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRF3415PBF

150V N-channel power MOSFET, 43A, 41mΩ RDS(on), TO-220AB package

Brand: infineon

Package: TO-220AB

IN STOCK: 2940pcs

Cargo cycle: 3-7 Days

The minimum order is 1

105017-1001

USB Type-C receptacle connector, 24-pin, SMD

Brand: Amphenol

Package: SMD (8.9 x 7.3 x 3.2 mm, right angle)

IN STOCK: 5335pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRLB3034PBF

IRLB3034PBF – 40V N-Channel StrongIRFET Power MOSFET (Logic Level), 1.7 mΩ (max) @ 10V; 2.0 mΩ @ 4.5V RDS(on), TO-220AB

Brand: infineon

Package: TO-220AB

IN STOCK: 9724pcs

Cargo cycle: 3-7 Days

The minimum order is 1

XC6SLX75-2FGG484I

Spartan-6 LX75 FPGA, 74637 logic cells, 132 DSP, 3096KB BRAM, 408 I/O, FBGA-484 23x23mm, -2 speed, industrial -40~100C, AMD Xilinx

Brand: xilinx

Package: FGG484 (484-ball fine-pitch BGA, 23x23mm body, 1.0mm ball pitch, 22×22 ball array, 6 I/O banks, lead-free)

IN STOCK: 890pcs

Cargo cycle: 3-7 Days

The minimum order is 1