Opens in a new tab

LP2951ACMM-3.3/NOPB

3.3V LDO, 100mA, 30V max, 380mV Vdo, VSSOP-8

2097

Effective Inventory

Image for reference only

Manufacturer Part:

LP2951ACMM-3.3/NOPB

Package:

8-Pin VSSOP / DGK (4.9 x 3.9 x 1.5 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Other recommendations you may be interested in.

Description

Product Overview

The LP2951ACMM-3.3/NOPB is a Texas Instruments 100mA, 30V low-dropout voltage regulator with 3.3V fixed output, 75uA quiescent current, 380mV dropout at 100mA, error flag, and logic-controlled shutdown. Packaged in VSSOP-8, -40C to +125C.

Key Specifications

Input Voltage 2.3 V to 30 V
Output Voltage 3.3 V fixed
Output Current 100 mA
Dropout Voltage 380 mV typ @ 100 mA
Quiescent Current 75 uA typ
Line Regulation 0.05% typ
Load Regulation 0.05% typ
Package VSSOP-8 (DGK)

Features

  • 2.3V to 30V wide input voltage range
  • 3.3V fixed output (0.5% typical accuracy)
  • 100mA guaranteed output current
  • 380mV typical dropout at 100mA
  • 75uA typical quiescent current
  • Error flag output for low output warning
  • Logic-controlled shutdown
  • Stable with low-ESR output capacitors

Applications

  • Battery-powered microcontroller supply
  • CMOS RAM keep-alive power
  • Low-power voltage reference
  • Automotive and industrial supply regulation
Product Introduction: LP2951ACMM-3.3/NOPB Product Introduction

The LP2951ACMM-3.3/NOPB is a Texas Instruments micropower low-dropout (LDO) voltage regulator in a VSSOP-8 (DGK) package. The device provides a fixed 3.3V output at up to 100mA from an input voltage range of 2.3V to 30V, making it suitable for battery-powered systems and high-voltage industrial applications. The 380mV typical dropout voltage at 100mA allows operation with minimal input-to-output voltage differential, extending battery life in portable applications. The 75uA typical quiescent current increases only slightly in dropout, further prolonging battery life. The device features tight output voltage accuracy (0.5% typical), extremely good load and line regulation (0.05% typical each), and a very low output voltage temperature coefficient, making it useful as a low-power voltage reference. The error flag output (active low) warns of a low output voltage condition, typically 5% below nominal, and can be used for power-on reset. The logic-compatible shutdown input enables the regulator to be turned off, reducing supply current to near zero. The device is stable with low-ESR output capacitors including ceramic capacitors.

Working Principle: LP2951ACMM-3.3/NOPB Working Principle

The LP2951ACMM-3.3/NOPB uses a PNP pass transistor in a common-collector (emitter-follower) configuration to achieve low dropout voltage. The error amplifier compares a fraction of the output voltage (from the internal resistor divider for the fixed 3.3V version) with a precision 1.235V bandgap reference. The error amplifier output drives the base of the PNP pass transistor, regulating the output voltage. In dropout, the PNP transistor saturates, and the dropout voltage is simply the VCE(sat) of the pass transistor (380mV at 100mA). The foldback current limit reduces the output current during short-circuit conditions to prevent excessive power dissipation. The thermal shutdown circuit disables the pass transistor when the junction temperature exceeds approximately 165C. The error flag comparator monitors the output voltage and pulls the ERROR pin low when the output drops below approximately 5% of the nominal voltage.

Pin Description: LP2951ACMM-3.3/NOPB Pin Definition and Functions
Pin Mnemonic Description
1 VOUT Regulated 3.3V output
2 SENSE Output voltage sense (for fixed versions)
3 SD Shutdown input (active low)
4 GND Ground
5 ERROR Error flag output (open collector)
6 FB Feedback / tap (internal for fixed)
7 TAP Internal divider tap
8 VIN Input supply (2.3-30V)
Application Scenarios: In which products and applications is LP2951ACMM-3.3/NOPB used
  • Battery-powered MCU 3.3V supply with 75uA IQ extending run time and error flag for low-battery detection
  • CMOS RAM 3.3V keep-alive supply with 40mV dropout at light load for data retention during power cycling
  • Industrial 24V to 3.3V sensor supply with shutdown for power gating and 30V input rating
  • Low-power 3.3V voltage reference with 0.05% line/load regulation for precision ADC bias
Alternative Models: What chips are recommended as replacements for LP2951ACMM-3.3/NOPB
Model Manufacturer Key Difference
LP2951ACMM-5.0/NOPB TI 5.0V fixed output version
LP2951ACMM/NOPB TI Adjustable version (1.24-29V)
TLV70033DDCR TI 3.3V, 300mA, smaller SOT-23-5
TPS7A3300RGTT TI 3.3V, ultra-low noise LDO

Recommend Parts

RK73H1ETTP20R0F

20Ohm +/-1% 0.063W thick film resistor, 0402, +/-100 ppm/C, AEC-Q200

Brand: KOA Speer

Package: 0402 (1005 Metric) 1.0 x 0.5 x 0.35 mm

IN STOCK: 33180pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS77001DBVR

50mA LDO, adjustable 1.2-5.5V out, 35mV dropout, 17µA IQ, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.45 mm)

IN STOCK: 5000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

TPS61021ADSGR

3A synchronous boost converter, 1.8-5.5V, VSSOP-8

Brand: TI

Package: VSSOP-8 (3.0 x 3.0 mm, DSG package)

IN STOCK: 12398pcs

Cargo cycle: 3-7 Days

The minimum order is 1

S1MB-13-F

1A 1000V GPP rectifier, 1.1V VF, 3μs trr, SMB/DO-214AA, -65~150°C

Brand: Diodes Inc

Package: SMB / DO-214AA (4.57 x 3.94 x 2.50mm)

IN STOCK: 3679pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADUM5000ARWZ-RL

500mW isolated DC-DC converter, 3.3/5V, SOIC-16W

Brand: ADI

Package: SOIC-16W (10.3 x 7.5 mm, RW package)

IN STOCK: 6373pcs

Cargo cycle: 3-7 Days

The minimum order is 1

ADS830E/2K5

8-bit 60MSPS high-speed ADC, TSSOP-24

Brand: TI

Package: TSSOP-24 (7.8 x 4.4 mm)

IN STOCK: 9357pcs

Cargo cycle: 3-7 Days

The minimum order is 1