Opens in a new tab

LPS22HHTR

260-1260hPa pressure sensor, 0.28Pa noise, I2C/SPI, HLGA-4

7800

Effective Inventory

Image for reference only

Manufacturer Part:

LPS22HHTR

Package:

HLGA-4 (2.5 x 2.5 x 0.68 mm)

Brand:

Quality Commitment

Shipping & Payment

Service & Packaging

Product Manual

Description

Product Overview

The LPS22HHTR is a STMicroelectronics ultra-low-noise 260-1260hPa absolute pressure sensor with 40Hz ODR, I2C/SPI output, and embedded temperature compensation. Packaged in HLGA-4 (2.5×2.5mm), -40C to +85C.

Key Specifications

Range 260 to 1260 hPa
Resolution 24-bit
ODR 1 to 40 Hz
Interface I2C / SPI
Noise 0.28 Pa RMS
Accuracy +/-0.5 hPa

Features

  • 260-1260hPa pressure range
  • 24-bit resolution
  • 0.28Pa RMS noise
  • +/-0.5hPa accuracy
  • I2C and SPI interface
  • Embedded FIFO (128 samples)
  • 2.5×2.5mm HLGA-4 package

Applications

  • Weather station and altimeter
  • Indoor navigation
  • Drone altitude hold
  • Healthcare respiratory
Product Introduction: LPS22HHTR Product Introduction

The LPS22HHTR is a STMicroelectronics ultra-low-noise piezoresistive absolute pressure sensor in a 2.5×2.5mm HLGA-4 package. The 260 to 1260hPa measurement range covers all Earth surface altitudes and weather conditions. The 0.28Pa RMS noise is among the lowest for MEMS pressure sensors, enabling high-resolution altitude measurement (approximately 2.3cm altitude resolution). The +/-0.5hPa absolute accuracy over the full temperature range provides reliable weather forecasting and altimetry. The sensor outputs 24-bit pressure and 16-bit temperature data through I2C (up to 400kHz) or SPI (up to 10MHz) interfaces. The embedded 128-sample FIFO stores pressure and temperature readings, reducing host processor read frequency and power consumption. The output data rate is programmable from 1Hz to 40Hz. The embedded temperature compensation algorithm runs automatically, applying factory-calibrated coefficients stored in on-chip OTP memory. The -HH suffix indicates the high-accuracy version. The TR suffix indicates tape-and-reel packaging. Packaged in HLGA-4 rated for -40C to +85C.

Working Principle: LPS22HHTR Working Principle

The LPS22HH uses a silicon MEMS piezoresistive pressure sensor die. A flexible silicon membrane with embedded piezoresistors deflects under applied pressure, changing the resistor values. A Wheatstone bridge circuit converts the resistance change to a differential voltage proportional to pressure. An internal 24-bit ADC digitizes the bridge output. A second temperature sensor die provides the temperature reading used for compensation. Factory calibration stores individual sensor offset, sensitivity, and temperature coefficient parameters in on-chip OTP memory. During operation, the compensation engine applies these coefficients to correct the raw pressure reading for temperature effects, producing the compensated output value. The FIFO accumulates samples at the configured ODR, with watermark, overwrite, and full interrupts. The device can be configured for one-shot mode (triggered conversion) or continuous mode for regular measurement streams. Power consumption is approximately 12uA in low-power mode at 1Hz ODR.

Pin Description: LPS22HHTR Pin Definition and Functions
Pin Mnemonic Description
1 VDD_IO I/O supply (1.71-3.6V)
2 VDD Analog supply (1.71-3.6V)
3 GND Ground
4 SDA/SDI I2C data / SPI data in
5 CS SPI chip select (I2C: pull high)
6 SCL/SPC I2C clock / SPI clock
7 SDO SPI data out / I2C addr
8 INT_DRDY Data ready interrupt
Application Scenarios: In which products and applications is LPS22HHTR used
  • Weather station barometric pressure measurement with 0.28Pa noise for accurate forecasting
  • Indoor floor-level navigation with 2.3cm altitude resolution from differential pressure
  • Drone altitude hold and barometric compensation with 40Hz ODR
  • Healthcare respiratory monitoring and spirometry with high-resolution pressure sensing
Alternative Models: What chips are recommended as replacements for LPS22HHTR
Model Manufacturer Key Difference
LPS22HB ST Lower accuracy version
LPS33HW ST Waterproof version
BMP390 Bosch Similar high-precision
DPS310 Infineon Similar low-noise

Recommend Parts

TMP275AIDR

0.5C I2C temp sensor, 12-bit, 2.7-5.5V, alert output, 8-SOIC

Brand: TI

Package: 8-SOIC (4.90 x 3.91 x 1.50 mm)

IN STOCK: 3681pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IL485E

NVE IL485E IsoLoop isolated RS-485 transceiver, 2.5kVrms isolation, 35Mbps, 16-SOIC WB

Brand: nve

Package: SOIC-16 WB

IN STOCK: 5280pcs

Cargo cycle: 3-7 Days

The minimum order is 1

IRFS4227TRLPBF

IRFS4227TRLPBF – 200V N-Channel HEXFET PDP Switch Power MOSFET, 26 mΩ RDS(on), D2PAK (TO-263)

Brand: infineon

Package: D2PAK (TO-263)

IN STOCK: 4334pcs

Cargo cycle: 3-7 Days

The minimum order is 1

CD4070BM96

Quad 2-input XOR gate, 3-18V CMOS, 65ns at 10V, SOIC-14

Brand: TI

Package: SOIC-14 (8.75 x 3.9 x 1.5mm)

IN STOCK: 4245pcs

Cargo cycle: 3-7 Days

The minimum order is 1

AB1526

Bluetooth 5.0 Dual Mode Audio SoC, TWS, AAC, Dual-mic ENC, Integrated Charger, BGA

Brand: airoha

Package: BGA

IN STOCK: 25000pcs

Cargo cycle: 3-7 Days

The minimum order is 1

LP2980IM5-5.0

50mA micropower ultra-low-dropout regulator, 5V, SOT-23-5

Brand: TI

Package: SOT-23-5 (2.9 x 1.6 x 1.1 mm)

IN STOCK: 2557pcs

Cargo cycle: 3-7 Days

The minimum order is 1